2007 FORD FIESTA coolant reservoir

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 44 Duratec-I 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-1 44
INSTALLATION
61. Using the special tool, connect the coolant
hose to the coolant distribution housing. 64. Attach the coolant expansion tank to the
bracket.
/
62. Attach the brake booster vacuum line to 65. Using the special tool, connect the degas
the intake manifold.
hose to the cylinder head.
63. Connect the low pressure evaporate 66. Attach the power steering fluid reservoir to
emission (EVAP) hose to the EVAP valve.
the bracket.
2006.0 Fiesta 12/2006 G380459en
procarmanuals.com

303-01 B-5 Engine - 2.OL Duratec-HE (M14) 303-01 B-5
SPECIFICATIONS
Torque Specifications - --- -- - -- -
Description Nm l b-ft Ib-in
Air cleaner retaining bracket
Air cleaner resonator support bracket retaining bolts Battery cable to generator electrical connector
I Cylinder head retaining bolts I a) I - I - I
Battery tray support bracket retaining bolts
I
--
I Camshaft bearing caps retaining bolts a) IT
15
15
I Camshaft sprocket retaining bolts I 72 I 53 I - I
25
I Camshaft position (CMP) sensor retaining bolt I 6 1 - I 53 I
11
I1
-
-
18
I Engine front cover lower blanking plug I 12 I 9 I - I
-
Engine front cover retaining bolts
Engine front cover upper blanking plug
I Engine support insulator retaining bolts I 48 I 35 I - I
Engine wiring harness bracket to valve cover
retaining nut
a)
10
I Generator upper retaining bolt I 25 I 18 I - I
-
-
I Coolant plugs (4) to cylinder head I 75 I 55 I - I
-
89
Hood latch lever retaining bolts
Crankshaft pulley retaining bolts
Coolant expansion tank retaining nut
Coolant plug to cylinder block
I Power steering pump retaining bolt I 23 I 17 I - I
15
a)
8
43
I
--
I Power steering bracket retaining nut 15 IT
Power steering reservoir retaining bolts
Power steering pipe to the power steering
Power steering supply line to intake manifold
retaining bolt
11
-
-
32
Power steering high-pressure line retaining bracket
retaining bolt
-
-
71
-
9
65
I Power steering return line support bracket retaining I 15 I 11 I - I
1 nut
-
48 80 -
Exhaust
manifold bracket retaining bolts
2006.0 Fiesta 1212006 G451278en
Exhaust manifold upper heat shield retaining bolts
Exhaust manifold lower heat shield retaining bolts
Exhaust manifold to the cylinder head retaining nuts
Exhaust manifold studs to cylinder head
25
10
10
55
17 18
-
-
-
41
13 89
89 -
-
procarmanuals.com

303-01 B-I17 Engine - 2.OL Duratec-HE (M14) 303-01 B-117
INSTALLATION
37. Using the special tool, connect the steering
Connect the clutch slave cylinder supply
gear to power steering fluid reservoir return
line.
I I line to the power steering fluid reservoir. Install the spring clip.
38.
Attach the steering gear to power steering 41. Connect the reversing lamp switch
fluid reservoir return line support bracket
electrical connector.
to the generator.
42. Lower the vehicle.
39. Connect the A/C low pressure switch
connector. 43. Install the coolant expansion tank.
40a &AUTION:I~ brake fluid is spilt on the
paintwork, the affected area must be
immediately washed down with cold water.
N0TE:Make sure the spring clip is correctly seated.
2006.0 Fiesta 1212006 ~451291 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-7 Duratec-HE (M14) 303-04B-7
DIAGNOSIS AND TESTING
I
The block heater can be connected to an external Throttle body
power supply, which will pre-heat the engine
i coolant contained within the cylinder block. The
' heated coolant will radiate heat to the fuel rail,
which will warm the contained fuel. Sufficient
warmed fuel is stored in the fuel rail to allow the
engine to start and continue running correctly, until
the engine combustion generates sufficient heat
to maintain correct operating conditions.
Fuel rail
The throttle body on Ethanol E85 vehicles is the
same as non Ethanol E85 variants. This is a fully
electronic controlled and monitored component.
The PCM adapts to the wear characteristics of the
throttle plate. If a new throttle body is installed, it
is necessary to teach the values of the new throttle
body to the PCM. If installing a new throttle body,
follow the initialization procedure.
REFER to: Throttle Body
(303-04C, Removal and
Installation).
The fuel rail on Ethanol E85 vehicles is the same
' as non Ethanol E85 variants. The fuel rail function
is to supply a reservoir of fuel at equal pressure
for all four fuel injectors.
2006.0 Fiesta i212006 GI 65371 en
procarmanuals.com