2007 FIAT PANDA ECU

62
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
To restore the use of the rear seat: lift the
seat back and push it backwards until you
hear the locking click and make sure the
seat belts are at the front of the seat back.
The car can be fitted, as optional, with sep-
arate rear seats.
The boot extension possibilities offered
by the split seat are many and they should
be chosen according to the number of
passengers and the amount of luggage to
be carried:
❒total extension with right and left side
of the seat tilted as described above;
❒partial extension with left or right side
of the seat tilted and place only for No.
1 rear passenger.
IMPORTANT If in the boot there is a
rather heavy load and you are travelling at
night, check and adjust aiming of the main
beam headlights (see “Headlights” in this
section).EXTENDING THE BOOT
(versions with rear sliding seat)
fig. 79 and 80
Partial extension
Use lever A(in the passenger’s compart-
ment) or the central tab Din the boot to
move the seat forward.
Total extension
Remove the rear parcel shelf as previous-
ly described (see versions with rear fixed
seat).
Use lever Aor central tab Din the boot
to move the seat to the required position
(e.g.: fully forward for total boot exten-
sion);
Lift lever Bor Cor pull side tabs Eor F
in the boot to release the seat back rest
section to tilt; both if you want to tilt the
whole back rest. EXTENDING THE BOOT
(versions with rear fixed seat)
fig. 78
Proceed as follows:
1) Remove the rear parcel shelf and fit it
behind the back rests. To remove the rear
parcel shelf, release catches A(one per
side) and pull the rear parcel shelf out-
wards.
2) Operate the levers on the seat back
outer side and tilt the seat back forwards
putting aside the seat belts.
For central seat belts with three anchor
point see paragraph “Use of the central
seat belt” in section “Safety devices”.
fig. 78F0G0131mfig. 79F0G0257m
A heavy load that has not
been secured may cause se-
rious harm.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 62

64
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Before opening the bonnet,
check that windscreen wiper
arms are not lifted from the wind-
screen.
WARNING
fig. 83
C
B
F0G0075m
To close the bonnet fig. 83
Hold the bonnet up with one hand and,
with the other, remove rod Bfrom recess
Dand replace it in its clip C;
Lower the bonnet until it is about 20 cm
above the engine compartment, then let it
fall and make sure it is properly locked and
not just secured in safety position. In this
case do not press the bonnet but raise it
again and repeat the operation.
For safety reasons the bon-
net must be closed properly
to avoid its opening while the car is
travelling. Therefore, always check it
is properly closed and the catch en-
gaged. Should you notice that the
catch is not perfectly engaged when
travelling, stop the car immediately
and close the bonnet.
WARNING
If checks are needed in the
engine compartment, when
it is still hot, proceed with the utmost
care to avoid burns. Do not approach
the fan: it might start working also
with the ignition key removed. Wait
for the engine cool down.
WARNING
Scarves, ties and other loose
articles of clothing could
easily get caught up in moving parts.
This can be extremely dangerous.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 64

65
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
HEADLIGHTS
ADJUSTING THE HEADLIGHT
BEAM
The correct positioning of the headlight
beams is very important for the comfort
and safety not only of the person driving
the car but also all other road users. This
also covered by a specific law.
To ensure you and other drivers have the
best visibility conditions when travelling
with the headlights on, the headlights must
be set properly.
Have the headlight positioning checked at
a Fiat Dealership and adjusted if necessary.
Check the positioning of the headlight
beams whenever the weight or the load
position is changed.
ROOF RACK/
SKI RACK
FASTENERS fig. 84
The roof rack fastener seats Aare shown
in the figure.
To secure the roof rack, remove plugs B
(two per side).
A roof rack/ski rack especially designed for
Fiat Panda is available from Lineaccessori
Fiat.
On some versions, bars carrying all ob-
jects can be provided as an optional.
fig. 84F0G00203m
After travelling a few kilo-
metres, check that the at-
tachment fastening screws are tight.
WARNING
Never exceed the permitted
weight (see section “Techni-
cal specifications”.
060-080 Panda New GB 21-06-2007 13:48 Pagina 65

84
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
Boot extension: unfasten the belt through
button Mand guide the belt to prevent
it from twisting; overlap tongues Iand G,
on the catch Hin the reel compartment.
IMPORTANT After repositioning the
seats, restore proper seat belts conditions
for prompt use.PRETENSIONERS
To increase the efficiency of the front and
rear (where provided) seat belts, the Fiat
Panda is fitted with pretensioners. These
devices “feel”, through a sensor, that a vi-
olent crash is in progress and rewind the
seat belts a few centimetres. In this way
they ensure that the seat belt adheres per-
fectly to the wearer before the restrain-
ing action begins.
The seat belt locks to indicate that the de-
vice has intervened; the seat belt cannot
be drawn back up even when guiding it
manually.
IMPORTANT To obtain the highest de-
gree of protection from the action of the
pretensioning device, wear the seat belt
keeping it firmly close to the chest and
pelvis.
A small amount of smoke may be pro-
duced. This smoke is in no way toxic and
presents no fire hazard.
The pretensioner does not require any
maintenance or greasing. Anything that
modifies its original conditions invalidates
its efficiency. If due to unusual natural
events (floods, sea storms, etc.) the device
has been affected by water and mud, it
must necessarily be replaced. Seat belt with three anchor points
(for versions/markets where
applicable) fig. 5
The seat belt has two webbings and a dou-
ble buckle.
To use the seat belts, take the tongues out
of the reel compartment and pull the belt,
guide the belt to prevent it from twisting
then secure tongue Ginto buckle Lfitted
with the black button M.
To fasten the belt, run the belt and secure
tongue Iinto the corresponding buckle N.
To fasten the belt: press button Oand guide
the belt to prevent it from twisting.
fig. 5F0G0241m
Remember that in the case
of a violent collision, back
seat passengers not wearing seat belts
also represent a serious danger to the
passengers in the front.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 84

INSTALLING THE TOW HOOK
The towing device should be fastened to
the body by specialised personnel accord-
ing to any additional and/or integrative in-
formation supplied by the Manufacturer of
the device.
The towing device must meet current reg-
ulations with reference to 94/20/CEE Di-
rective and subsequent amendments.
For any version the towing device used
must match the towable weight of the car
on which it is to be installed.
For the electric connection a unified con-
nector should be used which is generally
placed on a special bracket normally fas-
tened to the towing device, and a special
ECU for external trailer light control shall
be installed on the car.
For the electric connection, a 7 pin
12VDC connection is to be used (CU-
NA/UNI and ISO/DIN Standards). Follow
the instructions provided by the car man-
ufacturer and/or the tow hitch manufac-
turer.An electric brake should be supplied di-
rectly by the battery through a cable with
a cross section of no less than 2.5 mm
2.
IMPORTANT Electric brake or other de-
vice shall be used with running engine.
In addition to the electrical branches, the
car electric system can only be connect-
ed to the supply cable for an electric brake
and to the cable for an internal light,
though not above 15W.
For connections use a preset control unit
with battery cable no less than 2.5 mm
2. Do not exceed the speed limits of the
country you are driving in. In any case do
not exceed 100 km/h.
108
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
The ABS system with which
the car may be fitted does
not control the trailer braking system.
Therefore be cautious on slippery
roads.
WARNING
Under no circumstances
should the car brake system
be altered to control the trailer brake.
The trailer braking system must be
fully independent of the car’s hy-
draulic system.
WARNING
101-112 Panda New GB 21-06-2007 13:50 Pagina 108

❒loosen the bolts on the wheel to be re-
placed with the tool E-fig. 4provided;
❒turn handle to partially open the jack;
❒loosen the clamping device B-
fig. 3;
❒take out the tool container Cand take
it near the wheel to be changed;
❒take the space saver spare wheel D;
❒to remove the wheel cap secured by
spring, use the screwdriver provided
levering on the three notches present
on the outer circumference;
fig. 4F0G0695m
128
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCYfig. 3F0G0078m
To change a wheel proceed as follows:
❒Stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequately
firm;
❒ turn the engine off and pull up the hand-
brake;
❒ engage first gear or reverse;
❒lift the luggage compartment mat A-
fig. 2;
fig. 2F0G0171m
123-154 Panda New GB 21-06-2007 13:51 Pagina 128

IMPORTANT Do not use inner tubes
with tubeless tyres. Check the inflation
pressure of the tyres and the spare wheel
regularly.
IMPORTANT You will need to change the
set of bolts if you want to change the type
of wheels fitted (alloy rims instead of steel
rims, and vice versa). You will have to
change the entire set of fastening bolts
with another set of suitably sized bolts and
adopt a specific spare wheel having differ-
ent building characteristics.
You should keep the bolts and spare
wheel in case you decide to use the orig-
inal type of wheel later on. ❒fasten the three other bolts with the
wrench provided;
❒lower the car and remove the jack;
❒fasten bolts completely, working in a
criss-cross fashion as shown in fig. 10.
fig. 10F0G0696m
131
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
When you have finished
❒arrange the space-saver spare wheel D-
fig. 3in the specific compartment in the
boot;
❒insert the partially open jack into the
container Cand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒ put the tools back into their places in
the container;
❒stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device B;
❒correctly reposition the boot stiff cov-
er.
123-154 Panda New GB 21-06-2007 13:51 Pagina 131