
63
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
BONNET
To open the bonnet fig. 81-82-83
Pull the red lever (under the dashboard)
as shown in the figure.
Lift leverA.
Open the bonnet and at the same time re-
lease the rodBfrom its clip C.
Insert the end of rod in its recess Don
the bonnet and leave it in safety position.
Restoring the seat position
To restore the use of the rear seat: lift the
seat back and push it backwards until you
hear the locking click and make sure the
seat belts are at the front of the seat back.
fig. 80F0G0258mfig. 81F0G0202m
Once you have released the
lever, check that the seat is
firmly locked in the runners by trying
to move it back and forth. Failure to
lock the seat in place could result in
the seat moving suddenly and the dri-
ver losing control of the car.
WARNING
The bonnet might fall vio-
lently if the support rod is
not positioned properly. This should
only be done when the car is station-
ary.
WARNING
fig. 82F0G0690m
060-080 Panda New GB 21-06-2007 13:48 Pagina 63

64
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Before opening the bonnet,
check that windscreen wiper
arms are not lifted from the wind-
screen.
WARNING
fig. 83
C
B
F0G0075m
To close the bonnet fig. 83
Hold the bonnet up with one hand and,
with the other, remove rod Bfrom recess
Dand replace it in its clip C;
Lower the bonnet until it is about 20 cm
above the engine compartment, then let it
fall and make sure it is properly locked and
not just secured in safety position. In this
case do not press the bonnet but raise it
again and repeat the operation.
For safety reasons the bon-
net must be closed properly
to avoid its opening while the car is
travelling. Therefore, always check it
is properly closed and the catch en-
gaged. Should you notice that the
catch is not perfectly engaged when
travelling, stop the car immediately
and close the bonnet.
WARNING
If checks are needed in the
engine compartment, when
it is still hot, proceed with the utmost
care to avoid burns. Do not approach
the fan: it might start working also
with the ignition key removed. Wait
for the engine cool down.
WARNING
Scarves, ties and other loose
articles of clothing could
easily get caught up in moving parts.
This can be extremely dangerous.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 64

67
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
This is done using non-transparent stick-
er tape as shown in the figure. The figure
refers to passing from left-hand drive to
right-hand drive.
ABS SYSTEM
(where provided)
The car is fitted with an ABS braking sys-
tem, which prevents the wheels from lock-
ing when braking, makes the most of road
grip and gives the best control when emer-
gency braking under difficulty road condi-
tions.
System is completed by EBD (Electronic
Braking Force Distribution), which dis-
tributes the braking action between front
and rear wheels.
IMPORTANT To have the maximum ef-
ficiency of the braking system, it is neces-
sary a setting period of about 500 km: dur-
ing this period, it is better to avoid sharp,
repeated and prolonged brakes. HEADLIGHT BEAM
ADJUSTMENT ABROAD fig. 87
Headlights are orientated as to drive in-
side the country of origin before selling
the car. When travelling in countries with
opposite driving direction, you need to
cover the headlight areas according to the
Road Code of the country you are trav-
elling in.
fig. 87F0G0691m
060-080 Panda New GB 21-06-2007 13:48 Pagina 67

68
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
FAILURE WARNINGS
ABS failure fig. 88
If warning light >lights up on the instru-
ment panel, together with the message on
the reconfigurable multifunction display
(where provided), see section “Warning
lights and messages”.
In this case the braking system will still be
effective, although without the anti-lock
device. Drive carefully to the nearest Fiat
Dealership to have the system checked.EBD failure fig. 89
It is indicated by the turning on of warn-
ing lights >and xon the instrument
panel, together with the message on the
reconfigurable multifunction display
(where provided), see section “Warning
lights and messages”.
In this case with sharp braking the rear
wheels might lock too early, with the pos-
sibility of skidding . Drive extremely care-
fully to the nearest Fiat Dealership to have
the system checked. ABS INTERVENTION
When the ABS cuts in, you will feel the
brake pedal pulsating slightly and the sys-
tem get noisier: it means that the speed
should be altered to fit the type of road sur-
face.
fig. 88F0G0158mfig. 89F0G0159mWhen the ABS cuts in, and
you feel the brake pedal pul-
sating, do not remove your foot, but
keep it pressed; in doing so you will
stop in the shortest amount of space
possible under the current road con-
ditions.
WARNING
If the ABS system cuts in, it
is a sign that the grip be-
tween the tyre and the road surface
has reached the limit: you must slow
down to match the speed to the road
grip available.
WARNING
The ABS exploits the road
hold available as much as
possible but cannot increase it. You
should always drive carefully on slip-
pery surfaces and avoid any unnec-
essary risks.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 68

74
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
PARKING SENSORS
(where provided)
Parking sensors are located in the rear
bumper fig. 95and their function is to in-
form the driver, through an intermittent
buzzer, about the presence of obstacles
behind the car.
ACTIVATION
The sensors are automatically activated
when the reverse gear is engaged.
The sound produced by the acoustic alarm
becomes louder when the distance be-
tween the car and the obstacle decreases.
BUZZER WARNINGS
When the reverse gear is engaged an in-
termittent acoustic signal is automatically
activated (short beep indicating that sen-
sors are active).
The acoustic signal:
❒ becomes louder as the reduction of dis-
tance between the car and the obsta-
cle decreases;
❒ becomes continuous when the distance
between the car and the obstacle is less
that 30 cm and stops if the distance rais-
es;
❒is constant if the distance is unvaried.Direction distances
Central action radius 120 cm
Side action radius 60 cm
If several obstacles are detected, the con-
trol unit indicates the nearest one. We suggest to stop immediately the car,
turn off the engine for about 20 seconds
and then re-start the car. If the warning
light
gstays on together with the mes-
sage on the reconfigurable multifunction
display (where provided), contact Fiat
Dealership.
IMPORTANT The steering may become
slightly stiff following parking manoeuvres
including a great deal of steering. This is
normal and caused by a system to prevent
motor overheating. No servicing is re-
quired. The electric power steering sys-
tem will return to normal operation the
next time the car is used.
fig. 95F0G0692m
Always switch the engine off,
remove the key from the
starting device and actuate the steer-
ing lock before carrying out any main-
tenance operation, especially when
the wheels are raised from the
ground. In case this is not possible
(e.g. when the key must be in MAR
position or the engine running); re-
move the electric power steering
main fuse before carrying out any
maintenance operation.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 74

82
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
When the car is parked on a steep slope
the reel mechanism may block; this is nor-
mal. The reel mechanism prevents the
webbing coming out when it is jerked or
if the car brakes sharply, in a collision or
when cornering at high speeds.
The rear seat is fitted with inertial seat
belts with three anchor points and reel.
As an optional, (only for homologated 5-
seat cars) also the centre seat can be fit-
ted with three anchor points and reel or
with lap belt with two anchor points for
versions/markets where applicable.
IMPORTANT Remember that in the
event of a violent collision, back seat pas-
sengers not wearing seat belts also rep-
resent a serious danger for front seat pas-
sengers.SEAT BELT HEIGHT
ADJUSTMENT (where provided)
Four different adjustments in height are
provided.
To adjust, press button A-fig. 2and low-
er or raise the grip B.
Always adjust the height of the seat belt
to fit the person wearing it: this precau-
tion could greatly reduce the risk of injury
in case of collision.
Correct adjustment is obtained when the
belt passes half way between the end of
the shoulder and the neck.
See texts and figures given in paragraph
“General instructions for using the seat
belts” in this section.
SEAT BELTS
USING THE SEAT BELTS fig. 1
The belt should be worn keeping the chest
straight and rested against the seat back.
To fasten the seat belts, take hold the
tongue Aand insert it into the buckle B,
until hearing the locking click. At removal,
if it jams, let it rewind for a short stretch,
then pull it out again without jerking.
To unfasten the seat belts, press button
C. Guide the seat belt with your hand
while it is rewinding, to prevent it from
twisting. Through the reel, the belt auto-
matically adapts to the body of the pas-
senger wearing it, allowing freedom of
movement.
fig. 1F0G0053mfig. 2F0G0054m
Never press button C when
travelling.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 82

83
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
For certain versions, the front seat belts
have just one fixed anchoring point C-
fig. 3on the door post.USING THE CENTRAL SEAT
BELT
Static lap belt with 2 anchor points
(for versions/markets where
applicable) fig. 4
To fasten the seat belt: fit the tongue A
into the buckle Buntil hearing the locking
click.
To unfasten the seat belt: press button C.
To adjust the belt: run the tape in the
buckle D, pulling the end E) to tighten and
section Fto loosen.
fig. 3F0G0195mfig. 4F0G0224m
Make height adjustment
when the car is stationary.
WARNING
After adjustment, always
check that the slider is an-
chored in one of the positions pro-
vided. To do this, with the button A
released, exert a further pressure to
allow the anchor device to catch if re-
lease did not take place at one of the
preset positions.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 83

84
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
Boot extension: unfasten the belt through
button Mand guide the belt to prevent
it from twisting; overlap tongues Iand G,
on the catch Hin the reel compartment.
IMPORTANT After repositioning the
seats, restore proper seat belts conditions
for prompt use.PRETENSIONERS
To increase the efficiency of the front and
rear (where provided) seat belts, the Fiat
Panda is fitted with pretensioners. These
devices “feel”, through a sensor, that a vi-
olent crash is in progress and rewind the
seat belts a few centimetres. In this way
they ensure that the seat belt adheres per-
fectly to the wearer before the restrain-
ing action begins.
The seat belt locks to indicate that the de-
vice has intervened; the seat belt cannot
be drawn back up even when guiding it
manually.
IMPORTANT To obtain the highest de-
gree of protection from the action of the
pretensioning device, wear the seat belt
keeping it firmly close to the chest and
pelvis.
A small amount of smoke may be pro-
duced. This smoke is in no way toxic and
presents no fire hazard.
The pretensioner does not require any
maintenance or greasing. Anything that
modifies its original conditions invalidates
its efficiency. If due to unusual natural
events (floods, sea storms, etc.) the device
has been affected by water and mud, it
must necessarily be replaced. Seat belt with three anchor points
(for versions/markets where
applicable) fig. 5
The seat belt has two webbings and a dou-
ble buckle.
To use the seat belts, take the tongues out
of the reel compartment and pull the belt,
guide the belt to prevent it from twisting
then secure tongue Ginto buckle Lfitted
with the black button M.
To fasten the belt, run the belt and secure
tongue Iinto the corresponding buckle N.
To fasten the belt: press button Oand guide
the belt to prevent it from twisting.
fig. 5F0G0241m
Remember that in the case
of a violent collision, back
seat passengers not wearing seat belts
also represent a serious danger to the
passengers in the front.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 84