2007 FIAT PANDA back light

63
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
BONNET
To open the bonnet fig. 81-82-83
Pull the red lever (under the dashboard)
as shown in the figure.
Lift leverA.
Open the bonnet and at the same time re-
lease the rodBfrom its clip C.
Insert the end of rod in its recess Don
the bonnet and leave it in safety position.
Restoring the seat position
To restore the use of the rear seat: lift the
seat back and push it backwards until you
hear the locking click and make sure the
seat belts are at the front of the seat back.
fig. 80F0G0258mfig. 81F0G0202m
Once you have released the
lever, check that the seat is
firmly locked in the runners by trying
to move it back and forth. Failure to
lock the seat in place could result in
the seat moving suddenly and the dri-
ver losing control of the car.
WARNING
The bonnet might fall vio-
lently if the support rod is
not positioned properly. This should
only be done when the car is station-
ary.
WARNING
fig. 82F0G0690m
060-080 Panda New GB 21-06-2007 13:48 Pagina 63

66
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SLANT COMPENSATION fig. 85
The car is fitted with an electrical device
for correcting the headlight slant. The de-
vice can be operated with the ignition key
at MARand the dipped beam headlights
are on.
When the car is loaded, it slopes back-
wards. This means the headlight beam ris-
es.
In this case, it is necessary to return it to
the correct position using buttons +and
–.
The display shows the positions during the
adjustment.ADJUSTING THE FRONT
FOGLIGHTS (where provided)
fig. 86
Have the headlight positioning checked at
a Fiat Dealership and adjusted if necessary.
fig. 85F0G0141mfig. 86F0G0076m
Correct positions according
to the load
Position 0- one or two passengers on
front seats.
Position 1- four passengers.
Position 2- four passengers + load in the
boot.
Position 3- driver + maximum admitted
load in the boot.
060-080 Panda New GB 21-06-2007 13:48 Pagina 66

77
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INSTALLATION OF ELECTRIC/
ELECTRONIC DEVICES
Electric/electronic devices installed after
buying the vehicle or in aftermarket shall
bear the and marking:
Fiat Auto S.p.A. authorizes the installation
of transceivers provided that installation
is carried out at a specialized shop, work-
manlike performed and in compliance with
manufacturer's specifications.
IMPORTANT Installation of devices re-
sulting in modifications of vehicle charac-
teristics may cause driving license seizing
by traffic agents and also the lapse of the
warranty as concerns defects due to the
abovementioned modification or traceable
back to it directly or indirectly.
Fiat Auto S.p.A. declines all responsibility
for damages caused by the installation of
non-genuine accessories or not recom-
mended by Fiat Auto S.p.A. and installed
not in compliance with the specified re-
quirements.RADIO TRANSMITTERS
AND CELLULAR TELEPHONES
Radio transceiver equipment (e.g.: HAM
radio systems and the like) shall not be
used inside the vehicle unless a separate
aerial is mounted on the roof.
IMPORTANT The use of similar devices
inside the passenger compartment (with-
out separated aerial) produces radio-fre-
quency electromagnetic fields which, am-
plified by the resonance effects inside the
passenger compartment, may cause elec-
trical systems equipping the vehicle to mal-
function. This could compromise safety in
addition to constituting a potential hazard
for the passengers.
In addition, transmission and reception of
these devices may be affected by the
shielding effect of the vehicle body.
As concerns EC-approved mobile phones
(GSM, GPRS, UMTS), strictly comply with
the instructions for use provided by the
mobile phone’s manufacturer. ACCESSORIES PURCHASED
BY THE OWNER
If after buying the car, you decide to install
electrical accessories that require a per-
manent electric supply (alarm, satellite an-
titheft system, etc.) or accessories that in
any case burden the electric supply, con-
tact Fiat Dealership, whose qualified per-
sonnel, besides suggesting the most suit-
able devices belonging to Lineaccessori Fi-
at, will also evaluate the overall electric ab-
sorption, checking whether the car’s elec-
tric system is able to withstand the load
required, or whether it needs to be inte-
grated with a more powerful battery.
fig. 97F0G0073m
060-080 Panda New GB 21-06-2007 13:48 Pagina 77

82
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
When the car is parked on a steep slope
the reel mechanism may block; this is nor-
mal. The reel mechanism prevents the
webbing coming out when it is jerked or
if the car brakes sharply, in a collision or
when cornering at high speeds.
The rear seat is fitted with inertial seat
belts with three anchor points and reel.
As an optional, (only for homologated 5-
seat cars) also the centre seat can be fit-
ted with three anchor points and reel or
with lap belt with two anchor points for
versions/markets where applicable.
IMPORTANT Remember that in the
event of a violent collision, back seat pas-
sengers not wearing seat belts also rep-
resent a serious danger for front seat pas-
sengers.SEAT BELT HEIGHT
ADJUSTMENT (where provided)
Four different adjustments in height are
provided.
To adjust, press button A-fig. 2and low-
er or raise the grip B.
Always adjust the height of the seat belt
to fit the person wearing it: this precau-
tion could greatly reduce the risk of injury
in case of collision.
Correct adjustment is obtained when the
belt passes half way between the end of
the shoulder and the neck.
See texts and figures given in paragraph
“General instructions for using the seat
belts” in this section.
SEAT BELTS
USING THE SEAT BELTS fig. 1
The belt should be worn keeping the chest
straight and rested against the seat back.
To fasten the seat belts, take hold the
tongue Aand insert it into the buckle B,
until hearing the locking click. At removal,
if it jams, let it rewind for a short stretch,
then pull it out again without jerking.
To unfasten the seat belts, press button
C. Guide the seat belt with your hand
while it is rewinding, to prevent it from
twisting. Through the reel, the belt auto-
matically adapts to the body of the pas-
senger wearing it, allowing freedom of
movement.
fig. 1F0G0053mfig. 2F0G0054m
Never press button C when
travelling.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 82

84
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
Boot extension: unfasten the belt through
button Mand guide the belt to prevent
it from twisting; overlap tongues Iand G,
on the catch Hin the reel compartment.
IMPORTANT After repositioning the
seats, restore proper seat belts conditions
for prompt use.PRETENSIONERS
To increase the efficiency of the front and
rear (where provided) seat belts, the Fiat
Panda is fitted with pretensioners. These
devices “feel”, through a sensor, that a vi-
olent crash is in progress and rewind the
seat belts a few centimetres. In this way
they ensure that the seat belt adheres per-
fectly to the wearer before the restrain-
ing action begins.
The seat belt locks to indicate that the de-
vice has intervened; the seat belt cannot
be drawn back up even when guiding it
manually.
IMPORTANT To obtain the highest de-
gree of protection from the action of the
pretensioning device, wear the seat belt
keeping it firmly close to the chest and
pelvis.
A small amount of smoke may be pro-
duced. This smoke is in no way toxic and
presents no fire hazard.
The pretensioner does not require any
maintenance or greasing. Anything that
modifies its original conditions invalidates
its efficiency. If due to unusual natural
events (floods, sea storms, etc.) the device
has been affected by water and mud, it
must necessarily be replaced. Seat belt with three anchor points
(for versions/markets where
applicable) fig. 5
The seat belt has two webbings and a dou-
ble buckle.
To use the seat belts, take the tongues out
of the reel compartment and pull the belt,
guide the belt to prevent it from twisting
then secure tongue Ginto buckle Lfitted
with the black button M.
To fasten the belt, run the belt and secure
tongue Iinto the corresponding buckle N.
To fasten the belt: press button Oand guide
the belt to prevent it from twisting.
fig. 5F0G0241m
Remember that in the case
of a violent collision, back
seat passengers not wearing seat belts
also represent a serious danger to the
passengers in the front.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 84

85
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
LOAD LIMITERS
To increase passenger’s safety, the front
and rear (where provided) seat belt reels
contain a load limiter which allows con-
trolled sag in such a way as to dose the
force acting on the shoulders during the
belt restraining action in case of front
crash.
GENERAL INSTRUCTIONS FOR
USING THE SEAT BELTS
The driver must comply with (and have
the car occupants follow) all the local law
regulations concerning the use of seat
belts. Always fasten the seat belts before
starting.
Seat belts are also to be worn by expec-
tant mothers: the risk of injury in the case
of accident is greatly reduced for them and
the unborn child if they are wearing a seat
belt. Of course they must position the
lower part of the belt very low down so
that it passes under the abdomen (as il-
lustrated in fig. 6).
fig. 6F0G0046m
The pretensioner can only
be used once. After a colli-
sion that has triggered it, have it re-
placed at a Fiat Dealership. Preten-
sioner validity is written on the label
set on the door contour sheet metal.
Pretensioners should be replaced at
Fiat Dealership as this date ap-
proaches.
WARNING
Operations which lead to
knocks, vibrations or localised
heating (over 100°C for a
maximum of 6 hours) in the
area around the pretensioners may
cause damage or trigger them. These
devices are not affected by vibrations
caused by irregularities of the road sur-
face or low obstacles such as kerbs, etc.
Contact a Fiat Dealership for any as-
sistance.For maximum safety, keep
the back of your seat up-
right, lean back into it and make sure
the seat belt fits closely across your
chest and hips. Make sure that the
seat belts of the front and rear pas-
sengers are fastened at all times! You
increase the risk of serious injury or
death in a collision if you travel with
the belts unfastened.
WARNING
Under no circumstances
should the components of
the seat belts and pretensioners be
tampered with or removed. Any op-
eration should be carried out by qual-
ified and authorised personnel. Al-
ways contact a Fiat Dealership.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 85

87
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
All restraint devices must bear the certi-
fication data, together with the control
brand, on a solidly fixed label which must
absolutely never be removed.
Over 1.50 m in height, from the point of
view of restraint systems, children are
considered as adults and wear the seat
belts normally.
Lineaccessori Fiat offers seats for each
weight group, which are the recommend-
ed choice, as they have been designed and
experimented specifically for Fiat cars.CARRYING CHILDREN
SAFELY
For optimal protection in the event of a
crash, all passengers must be seated and
wearing adequate restraint systems.
This is even more important for children.
This prescription is compulsory in all EC
countries according to EC Directive
2003/20/EC.
Compared with adults, their head is pro-
portionally larger and heavier than the rest
of the body, while the muscles and bone
structure are not completely developed.
Therefore, correct restraint systems are
necessary, other then adult seat belts.
The results of research on the best child
restraint systems are contained in the Eu-
ropean Standard ECE- R44. This Standard
enforces the use of restraint systems clas-
sified in five groups:
Group 0 0-10 kg in weight
Group 0+ 0-13 kg in weight
Group 1 9-18 kg in weight
Group 2 15-25 kg in weight
Group 3 weight 22 - 36 kg
SERIOUS DANGER: Never
place cradle child’s seats on
the front passenger seat of
cars fitted with passenger’s
air bag. The air bag activa-
tion could cause serious in-
juries, even mortal. You are advised
to carry children always on the rear
seats, as this is the most protected po-
sition in the case of a crash. In any
case, children’s seats must absolutely
not be fitted on the front seat of cars
with passenger’s air bag, which dur-
ing inflation could cause serious in-
jury, even mortal, regardless of the se-
riousness of the crash that triggered
it. Children may be placed on the
front seat of cars fitted with passen-
ger’s air bag deactivation. In this case,
it is absolutely necessary to check the
warning light
Fon the cluster to
make sure that deactivation has ac-
tually taken place (see paragraph
“Passenger’s front air bag” at item
“Front air bags”). The front passen-
ger’s seat shall be adjusted in the
most backward position to prevent
any contact between child’s seat and
dashboard.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 87

88
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
GROUP 2
Starting from 15 to 25 kg in weight, chil-
dren may be restrained directly by the car
belts fig 11.
The only function of the seat is to position
the child correctly in relation to the belts,
so that the diagonal part adheres to the
chest and not to the neck and that the
horizontal part clings to the child’s pelvis
and not the abdomen.
fig. 11F0G0049m
GROUP 1
Starting from 9 to 18 kg in weight, children
may be carried facing forwards, with seats
fitted with front cushion, through which
the car seat belt restrains both child and
seat fig. 10. GROUP 0 and 0+
Babies up to 13 kg must be carried facing
backwards on a cradle seat which, sup-
porting the head, does not induce stress
on the neck in the event of sharp decel-
eration.
The cradle is restrained by the car seat
belts, as shown in fig. 9and in turn it must
restrain the child with its own belts.
fig. 9F0G0047mfig. 10F0G0048m
The figure is only an example for mounting. Attain to the instructions
for fastening which must be enclosed with the specific child restrain-
ing system you are using.
WARNING
Seats exist which are suitable for covering weight groups 0 and 1 with a
rear connection to the car belts and their own belts to restrain the child.
Due to their size, they can be dangerous if installed incorrectly fastened to the car
belts with a cushion. Carefully follow the instructions for installation provided with
the seat.
WARNING
The figure is only an exam-
ple for mounting. Attain to
the instructions for fastening which
must be enclosed with the specific
child restraining system you are using.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 88