2007 FIAT PANDA pressure

SIDE/TAILLIGHTS
AND LOW BEAMS
(green)
FOLLOW ME HOME
(green)
Side/taillights and low beams
The warning light turns on when side/tail-
lights or low beams are turned on.
Follow me home
The warning light will turn when this de-
vice is active (see “Follow me home” in
section “Dashboard and controls”).
The display will show the dedicated mes-
sage.
3
120
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
ESP SYSTEM FAILURE
(amber)
Turning the ignition key to
MARthe warning light comes on but shall
go off after few seconds.
If the warning light does not go off or stays
on when travelling together with the but-
ton led ASR OFF, contact Fiat Dealer-
ship.
On certain versions the dedicated mes-
sage is displayed.
NoteWarning light flashing when driving
indicates that the ESP system is active.
á
HILL HOLDER FAILURE
(amber)
Turning the ignition key to
MARthe warning light comes on but shall
go off after few seconds.
The warning light will turn on when the
Hill Holder system is faulty. Contact Fiat
Dealership as soon as possible .
On certain versions the dedicated mes-
sage is displayed.
*
GENERIC FAILURE
INDICATION
(amber)
The warning light turns on in the follow-
ing circumstances.
Engine oil pressure
sensor failure
The warning light comes on when the en-
gine oil pressure sensor is faulty. Contact
Fiat Dealership as soon as possible.
Water in diesel fuel filter
See what described for warning light c.
Inertial fuel cut-off switch
intervened
The warning light comes on when the in-
ertial fuel cut-off switch is triggered.
The display will show the dedicated mes-
sage.
è
113-122 Panda New GB 26-06-2007 11:04 Pagina 120

127
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Alert other drivers that the
car is stationary in compli-
ance with local regulations: hazard
warning lights, warning triangle, etc.
Any passengers on board should leave
the car, especially if it is heavily laden.
Passengers should stay away from on-
coming traffic while the wheel is be-
ing changed. If parked on a slope or
rough surface, chock the wheels with
wedges or other suitable devices.
WARNING
When driving with a space-
saver spare wheel fitted, the
driving performance of the car
changes. Avoid accelerating or brak-
ing sharply, abrupt turns of fast cor-
nerings. The life of a spare wheel is
approx. 3000 km, after this distance
it should be replaced with another of
the same type. Never attempt to fit
a conventional tyre on a rim designed
for use as a space-saver spare wheel.
Have the punctured wheel repaired
and refitted as soon as possible. Two
or more space-saver spare wheels
should never be used together. Do not
grease the threads of bolts before in-
stalling them: they might slip out.
WARNING
The jack shall only be used
for changing wheels on the
car with which it is provided or on
cars of the same model. It must not
be used for other purposes such as for
instance raising cars of other models.
In no case should it be used for repairs
under the car. Incorrect positioning
of the jack may cause the jacked car
to fall. Do not use the jack for high-
er capacities than stated on its label.
Snow chains cannot be fitted to the
space-saver spare wheel. So, if a front
(drive) wheel is punctured and chains
are needed, a rear wheel should be
fitted to the front of the car and the
spare wheel should be fitted to the
rear. This way with two normal dri-
ve wheels, snow chains can be fitted
to them to solve an emergency.
WARNING
Fasten the wheel cap cor-
rectly to prevent the wheel
from coming free in motion. Never
tamper with the inflation valve. Nev-
er place tools between the rim and
tyre. Check and restore, if required,
the pressure of tyres and spare wheel
to the values given in section “Tech-
nical specifications”.
WARNING
Please note:
❒ the jack weight is 1,76 kg;
❒the jack requires no adjustment;
❒the jack cannot be repaired and in the
event of a fault it must be replaced by
another original one;
❒no tool other than its cranking device
may be fitted on the jack.
123-154 Panda New GB 21-06-2007 13:51 Pagina 127

IMPORTANT Do not use inner tubes
with tubeless tyres. Check the inflation
pressure of the tyres and the spare wheel
regularly.
IMPORTANT You will need to change the
set of bolts if you want to change the type
of wheels fitted (alloy rims instead of steel
rims, and vice versa). You will have to
change the entire set of fastening bolts
with another set of suitably sized bolts and
adopt a specific spare wheel having differ-
ent building characteristics.
You should keep the bolts and spare
wheel in case you decide to use the orig-
inal type of wheel later on. ❒fasten the three other bolts with the
wrench provided;
❒lower the car and remove the jack;
❒fasten bolts completely, working in a
criss-cross fashion as shown in fig. 10.
fig. 10F0G0696m
131
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
When you have finished
❒arrange the space-saver spare wheel D-
fig. 3in the specific compartment in the
boot;
❒insert the partially open jack into the
container Cand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒ put the tools back into their places in
the container;
❒stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device B;
❒correctly reposition the boot stiff cov-
er.
123-154 Panda New GB 21-06-2007 13:51 Pagina 131

134
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
fig. 4F0G0672mfig. 6F0G0698m
fig. 5F0G0673m
❒check that the compressor switch D-
fig. 4is set at 0 (off), start the engine,
fit plug E-fig. 5into the 12V outlet lo-
cated on the central console and then
turn the compressor on setting the
switch D-fig. 4in position I(on). Inflate
the tyre at the pressure value specified
in paragraph “Inflation pressure” in sec-
tion “Technical Specifications” Check tyre pressure on gauge F-
fig. 4with compressor off to obtain
precise reading;
❒if after 5 minutes it is still impossible
to reach at least 1.5 bar, disengage com-
pressor from valve and current outlet,
then move the car forth for approx. ten
metres in order to distribute the seal-
ing fluid inside the tyre evenly, then re-
peat the inflation operation;
❒If after this operation it is still impossi-
ble after 5 minutes to reach at least 1.8
bar, do not start driving since the tyre
is excessively damaged and the quick
tyre repair kit cannot guarantee suit-
able sealing, contact Fiat Dealership;
❒if reaching the tyre pressure specified
in paragraph “Inflation pressure” in sec-
tion “Technical Specifications”, start
driving immediately;
❒after driving for about 10 minutes stop
and check again the tyre pressure; pull
up the handbrake;
Apply the sticker in a visible
position for the driver to in-
dicate that the tyre has been treat-
ed with the quick tyre repair kit. Dri-
ve carefully especially when corner-
ing. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNING
If the pressure falls below 1.8
bars, do not drive any fur-
ther: the quick tyre repair kit Fix & Go
automatic cannot guarantee proper
hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
123-154 Panda New GB 21-06-2007 13:51 Pagina 134

135
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒if at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the near-
est Fiat Dealership.
It is of vital importance to
communicate that the tyre
has been repaired using the quick tyre
repair kit. Hand the instruction
brochure to the personnel charged
with treating the tyre repaired with
the kit.
WARNINGfig. 7F0G0699mfig. 8F0G0676m
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor can be also used just for
restoring pressure. Release cylinder con-
nection A-fig. 8and connect it directly to
the tyre valve fig. 7; in this way the cylin-
der is not connected to compressor and
the sealing fluid will not flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection A-fig. 8;
❒turn counter-clockwise the cylinder to
replace and raise it;
❒fit the new cylinder and turn it clock-
wise;
❒connect connection Ato the cylinder
and fit the transparent tube Binto the
proper space.
123-154 Panda New GB 21-06-2007 13:51 Pagina 135

139
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
To change the direction indicator bulb,
proceed as follows:
❒release clip A-fig. 21and remove cap
B;
❒turn the bulb-holder D-fig. 22and re-
move it (it is pressure-fitted);
IF AN EXTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
fig. 21F0G0089mfig. 22F0G0090m
fig. 23F0G0091m
FRONT LIGHT UNITS
To change the bulb, proceed as follows:
❒release clip A-fig. 21 and remove cap
B;
❒turn the bulb-holder C-fig. 22and re-
move it (it is pressure-fitted);
❒remove the burnt bulb E-fig. 23 and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
123-154 Panda New GB 21-06-2007 13:51 Pagina 139

SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒push the transparent cover A-fig. 27
towards car running direction (it is
pressure-fitted);
❒remove connector G-fig. 25;
❒release the bulb holder catch H;
❒remove the burnt bulb I-fig. 26and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
fig. 25F0G0093mfig. 27F0G0095m
fig. 26F0G0094m
140
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the burnt bulb F-fig. 24and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
To replace the main/dipped beam light
bulb, proceed as follows:
❒release clip A-fig. 21and remove cap
B;
fig. 24F0G0092m
123-154 Panda New GB 21-06-2007 13:51 Pagina 140

141
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the transparent cover A-fig.
28from bulb holder (it is pressure-fit-
ted);
❒remove the bulb Band replace it;
❒ refit the lens.
❒loosen cover C-fig. 30and remove the
connector D;
❒release clip E-fig. 31and remove the
bulb F;
❒refit by reversing the above mentioned
operations. FRONT FOG LIGHTS
(where provided)
To change the halogen bulb, proceed as
follows:
❒slacken the two fog light fastening
screws A-fig. 29on the bumper;
❒slacken the two fog light fastening
screws Bunder the bumper;
❒remove the protection including the fog
light and remove the connector;
fig. 29F0G0227mfig. 28F0G0604mfig. 30
TOPOFFON
F0G0228m
fig. 31F0G0229m
123-154 Panda New GB 21-06-2007 13:51 Pagina 141