2007 FIAT PANDA heating

46
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
lows heating of the passenger
compartment in the shortest
time, also giving a prompt feeling
of warmth.
w+μSplitting of the air flow between
the vents to the lower part of the
passenger compartment
(warmest air) and the dashboard
centre and side outlets (coolest
air).
¥+μSplitting of the air flow between
the windscreen and side window
demisting/defrosting vents and
the lower part of the passenger
compartment. This type of air dis-
tribution allows satisfactory heat-
ing of the passenger compart-
ment while preventing possible
misting of the windows.
The type of air distribution selected is
shown by lighting up of the relevant led on
the selected button.
To restore automatic air distribution con-
trol after a manual selection, press button
AUTO.
During automatic operation, under par-
ticular climate conditions, the system can
send air to the windscreen although the
relevant led does not turn on.Button -- L
Fast front windows
demisting/defrosting
Press button - the climate control system
will automatically switch on all the func-
tions required for fast windscreen and
front side window demisting/defrosting,
that is:
❒switches on climate control compres-
sor when climatic conditions are suit-
able;
❒air recirculation off;
❒maximum air temperature (HI);
❒activates proper fan speed according to
engine coolant temperature;
❒directs air flow to windscreen and front
side windows vents;
❒turns heated rear window on.
IMPORTANT Fast demisting/defrosting
function stays on for about 3 minutes,
since engine coolant temperature exceeds
50 °C (petrol versions) or 35 °C (Diesel
versions).
When the demisting/defrosting function is
on, the button led -and the heated rear
window button led (are on, whereas
the AUTObutton led will turn off; when
this function is on, the only operations
possible are fan speed adjustment and
heated rear window switching off.
To turn the function off, press again but-
ton - or press button AUTO. Buttons ÕÔ- F
Fan speed adjustment
Press buttons Õor Ôto increase or to
decrease the fan speed; the fan speed is
shown by the lit bars on the display.
The fan can be cut off only if the climate
control compressor has been switched off
(button B).
To restore automatic fan speed control,
press buttonAUTO.
Buttons ¥wμ- G H I
Air distribution
manual selection
Pressing these buttons it is possible to
choose manually one of the five possible air
distributions:¥Air flow to the windscreen and
front side window vents to
demist or defrost them.
wAir flow to central and side dash-
board vents to ventilate the chest
and the face during the hot sea-
son.
μAir flow towards the front and
rear lower parts of the passenger
compartment. Due to the natur-
al tendency of heat to spread up-
wards, this type of distribution al-
032-059 Panda New GB 21-06-2007 13:48 Pagina 46

74
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
PARKING SENSORS
(where provided)
Parking sensors are located in the rear
bumper fig. 95and their function is to in-
form the driver, through an intermittent
buzzer, about the presence of obstacles
behind the car.
ACTIVATION
The sensors are automatically activated
when the reverse gear is engaged.
The sound produced by the acoustic alarm
becomes louder when the distance be-
tween the car and the obstacle decreases.
BUZZER WARNINGS
When the reverse gear is engaged an in-
termittent acoustic signal is automatically
activated (short beep indicating that sen-
sors are active).
The acoustic signal:
❒ becomes louder as the reduction of dis-
tance between the car and the obsta-
cle decreases;
❒ becomes continuous when the distance
between the car and the obstacle is less
that 30 cm and stops if the distance rais-
es;
❒is constant if the distance is unvaried.Direction distances
Central action radius 120 cm
Side action radius 60 cm
If several obstacles are detected, the con-
trol unit indicates the nearest one. We suggest to stop immediately the car,
turn off the engine for about 20 seconds
and then re-start the car. If the warning
light
gstays on together with the mes-
sage on the reconfigurable multifunction
display (where provided), contact Fiat
Dealership.
IMPORTANT The steering may become
slightly stiff following parking manoeuvres
including a great deal of steering. This is
normal and caused by a system to prevent
motor overheating. No servicing is re-
quired. The electric power steering sys-
tem will return to normal operation the
next time the car is used.
fig. 95F0G0692m
Always switch the engine off,
remove the key from the
starting device and actuate the steer-
ing lock before carrying out any main-
tenance operation, especially when
the wheels are raised from the
ground. In case this is not possible
(e.g. when the key must be in MAR
position or the engine running); re-
move the electric power steering
main fuse before carrying out any
maintenance operation.
WARNING
060-080 Panda New GB 21-06-2007 13:48 Pagina 74

85
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
LOAD LIMITERS
To increase passenger’s safety, the front
and rear (where provided) seat belt reels
contain a load limiter which allows con-
trolled sag in such a way as to dose the
force acting on the shoulders during the
belt restraining action in case of front
crash.
GENERAL INSTRUCTIONS FOR
USING THE SEAT BELTS
The driver must comply with (and have
the car occupants follow) all the local law
regulations concerning the use of seat
belts. Always fasten the seat belts before
starting.
Seat belts are also to be worn by expec-
tant mothers: the risk of injury in the case
of accident is greatly reduced for them and
the unborn child if they are wearing a seat
belt. Of course they must position the
lower part of the belt very low down so
that it passes under the abdomen (as il-
lustrated in fig. 6).
fig. 6F0G0046m
The pretensioner can only
be used once. After a colli-
sion that has triggered it, have it re-
placed at a Fiat Dealership. Preten-
sioner validity is written on the label
set on the door contour sheet metal.
Pretensioners should be replaced at
Fiat Dealership as this date ap-
proaches.
WARNING
Operations which lead to
knocks, vibrations or localised
heating (over 100°C for a
maximum of 6 hours) in the
area around the pretensioners may
cause damage or trigger them. These
devices are not affected by vibrations
caused by irregularities of the road sur-
face or low obstacles such as kerbs, etc.
Contact a Fiat Dealership for any as-
sistance.For maximum safety, keep
the back of your seat up-
right, lean back into it and make sure
the seat belt fits closely across your
chest and hips. Make sure that the
seat belts of the front and rear pas-
sengers are fastened at all times! You
increase the risk of serious injury or
death in a collision if you travel with
the belts unfastened.
WARNING
Under no circumstances
should the components of
the seat belts and pretensioners be
tampered with or removed. Any op-
eration should be carried out by qual-
ified and authorised personnel. Al-
ways contact a Fiat Dealership.
WARNING
081-100 Panda New GB 21-06-2007 13:49 Pagina 85

If the engine does not start at the first at-
tempt, return the ignition key to STOP
before repeating starting.
If, when the ignition key is at MAR, warn-
ing light
Yremains lit, turn the key to
STOPand then back to MAR; if the
warning light remains on, try with the oth-
er keys provided with the car.
If you still cannot start the engine, contact
Fiat Dealership.HOW TO WARM UP THE
ENGINE AFTER IT HAS JUST
STARTED
Proceed as follows:❒ Drive off slowly, letting the engine turn
at medium revs. Do not accelerate
abruptly;
❒Do not drive at full performance for the
initial kilometres. Wait until the coolant
temperature gauge starts moving.
EMERGENCY START-UP
If the instrument panel warning light
Ystays on with fixed light, the emergency
start-up can be performed by using the
CODE card code (see section “In an
emergency”). STARTING PROCEDURE
FOR DIESEL VERSIONS
Proceed as follows:
❒ Ensure that the handbrake is up;
❒ Put the gear lever into neutral;
❒Turn the ignition key to MAR: the
warning lights
mand Yon the in-
strument panel will turn on;
❒Wait for the warning lights Yand
mto turn off. The hotter the engine
is, the quicker this will happen;
❒ Press the clutch pedal down to the
floor without touching the accelerator;
❒Turn the ignition key to AVVas soon
as warning light
mgoes out. If you
wait too long you will lose the benefit
of the work done by the glow plugs.
Release the key as soon as the engine
starts.
IMPORTANT With cold engine, the ac-
celerator pedal shall be completely re-
leased while turning the ignition key to
AVV.
103
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
The warning light mwill
flash for 60 seconds at start-
up or during prolonged crank-
ing to indicate a fault in the
glow plug heating system. You can use
the car as usual if the engine starts but
you should contact Fiat Dealership as
soon as possible.
Never bump start the engine
by pushing, towing or coast-
ing downhill. These opera-
tions could cause fuel to flow
into the catalytic exhaust system and
damage it beyond repair.
101-112 Panda New GB 21-06-2007 13:50 Pagina 103

133
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IT SHOULD BE NOTICED THAT:
The sealing fluid of the quick tyre repair
kit is effective with external temperatures
between –20 °C and +50 °C.
The sealing fluid has limited life.
The compressor shall not be
operated for more than 20
minutes. Risk of overheating!. Tyres
repaired with the quick tyre repair kit
shall be used temporarily only.
WARNING
The cylinder contains ethyl-
ene glycol. The cylinder con-
tains latex: it can cause allergic reac-
tions. It is harmful if ingested or in-
haled and irritant for the eyes and in
case of contact. In case of contact
rinse immediately with water and take
off contaminated clothes. If swal-
lowed, do not induce vomit, rinse out
the mouth, drink a lot of water and
call the doctor immediately. Keep
away from children. This product must
not be used by asthmatics. Do not in-
hale vapours. Call the doctor imme-
diately in case of allergic reactions.
Keep the cylinder in the space provid-
ed for the purpose and far from heat.
The sealing fluid has limited life.
WARNING
Replace the cylinder if seal-
er has run out. Do not throw
away the cylinder and the
sealing fluid. Have the sealing
fluid and the cylinder disposed of in
compliance with national and local
regulations.
Put on the protection gloves
provided together with quick
tyre repair kit.
WARNING
INFLATING PROCEDURE
❒Pull up the handbrake. Loosen tyre
inflation valve cap, take out the filler
hose A-fig. 3and screw the ring nut
Bon the tyre valve;
fig. 3F0G0697m
123-154 Panda New GB 21-06-2007 13:51 Pagina 133

172
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
WINDSCREEN/
REAR WINDOW
WIPERS
BLADES
Periodically clean the rubber part using
special products; TUTELA PROFES-
SIONAL SC 35 is recommended.
If the rubber blades are bent or worn they
should be replaced. In any case they should
be changed once a year.
A few simple notions can reduce the pos-
sibility of damage to the blades:
❒if the temperature falls below zero,
make sure that ice has not frozen the
rubber against glass. If necessary, thaw
using an antifreeze product;
❒remove any snow from the glass: in ad-
dition to protecting the blades, this pre-
vents effort on the motor and over-
heating;
❒do not operate the windscreen and
rear window wipers on dry glass.Changing the windscreen
wiper blades fig. 16
Proceed as follows:
❒raise the windscreen wiper arm Aand
position the blade so that it forms an
angle of 90° with the arm;
❒press tab Bof the coupling spring and
remove the blade to be replaced from
the arm A;
❒fit the new blade by inserting the tab in-
to the special slot in the arm. Make sure
it is properly locked into place.
fig. 16F0G0218m
Driving with worn wiper
blades is a serious hazard,
because visibility is reduced in bad
weather.
WARNING
Changing the rear
window blade fig. 17
Proceed as follows:
❒raise the cover Aand remove the arm
from the car, slackening the nut Bthat
fastens it to the pivot pin;
❒ fit the new arm, positioning it correct-
ly, and fully tighten the nut;
❒ lower the cover.
fig. 17F0G0077m
155-176 Panda New GB 21-06-2007 13:52 Pagina 172

174
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
❒spraying of plastic parts, with a protec-
tive function in the more exposed
points: underdoor, inner fender parts,
edges, etc;
❒ Use of “open” boxed sections to pre-
vent condensation and pockets of mois-
ture from triggering rust inside.
BODY AND UNDERBODY
WARRANTY
Your Fiat Panda is covered by warranty
against perforation due to rust of any orig-
inal element of the structure or body.
For the general terms of this warranty, re-
fer to Fiat Warranty Booklet.
ADVICE FOR PRESERVING
THE BODYWORK
Paint
Paintwork does not only serve an aesteth-
ic purpose, but also protects the under-
lying sheet metal.
In the case of deep scrapes or scores, you
are advised to have the necessary touching
up carried out immediately to avoid the for-
mation of rust. For touching up use only
original products (see “Bodywork paint
identification plate” in section “Technical
specifications”).Normal paint maintenance consists in
washing at intervals depending on the con-
ditions and environment of use. For exam-
ple, in highly polluted areas, or if the roads
are sprayed with salt, it is wise to wash the
car more frequently.
To correctly wash the car:
❒ remove the aerial from the roof to pre-
vent damage to it if the car is washed in
an automatic system;
❒ wash the body using a low pressure jet
of water;
❒ wipe a sponge with a slightly soapy so-
lution over the bodywork, frequently
rinsing with the sponge;
❒ rinse well with water and dry with a jet
of air or a chamois leather.
When drying, take particular care with the
less visible parts like door surrounds, bon-
net and around the headlights where wa-
ter may stagnate. The car should not be
taken to a closed area immediately, but left
in the open so that residual water can
evaporate.
Do not wash the car after it has been left
in the sun or with the bonnet hot: this may
alter the shine of the paintwork.Windows
Use specific window cleaner products.
Use also clean cloths to avoid scratching
the glass or damaging the transparency.
IMPORTANT The inside of the
rearscreen should be wiped gently with a
cloth in the direction of the filaments to
avoid damaging the heating device. Exterior plastic parts must be cleaned in
the same way as the rest of the car.
Where possible, do not park under trees;
the resinous substance many species re-
lease give the paint a dull appearance and
increase the possibility of triggering rust
processes.
IMPORTANT Bird droppings must be
washed off immediately and thoroughly as
the acid they contain is particularly ag-
gressive.
Detergents cause water pollu-
tion. Therefore the engine
compartment should be
washed in areas equipped for
collecting and purifying the liquid used
in the washing process.
155-176 Panda New GB 21-06-2007 13:52 Pagina 174

Fiat CODE (system) ......................... 7
Fix & Go (tyre repair kit) ................. 132
Flashing the headlights ....................... 48
Fluid levels ............................................ 161
– checks ............................................. 161
Fluids and lubricants ........................... 191
Follow me home (device) ................. 49
Front ceiling lights .............................. 50
– bulb replacement........................... 144
– control ............................................ 50
Front fog lights .................................... 52
– bulb replacement .......................... 141
– control button .............................. 52
Fuel ........................................................ 190
– consumption................................... 193
– cut-off switch.................................. 52
– level gauge ....................................... 17
– refuelling......................................78-190
– tank capacity................................... 190
Fuel feed/ignition ................................ 182
Fuel filler cap ....................................... 78
Fuel lid ................................................... 78
Fuel level gauge ................................... 17
Fuses (replacement) ........................... 146
Gearbox .............................................. 105
– technical data ................................ 182
– using manual gearbox .................. 105
Glass holder ......................................... 54Glove box/oddment compartment .. 54
Handbrake .......................................... 104
Hazard lights ........................................ 52
Head restraints..................................... 34
Headlight washer................................. 49
– control ............................................ 49
– fluid level ........................................ 164
Headlights.............................................. 65
– adjustment abroad......................... 67
– beam adjustment .......................... 66
– front fog light adjustment ........... 66
– headlight slant adjusting device . 66
Heated rear window .......................... 52
Heating and ventilation system ........ 38
Hill Holder system.............................. 70
Identification data .............................. 178
Ignition switch ..................................... 11
In an emergency .................................. 123
Instrument panel ................................. 13
– light adjustment.............................. 21
Instruments .......................................... 16
Interior fittings .................................... 53
Interiors ................................................ 175
Isofix Type (child restraint system) 91
Jack ........................................................ 127
Jacking the car ..................................... 153
Key with remote control ................ 9 – front bulb replacement ............... 139
– rear bulb replacement ................. 142
– side bulb replacement ................. 140
Door lock ............................................. 57
Door unlocking ................................... 57
Doors..................................................... 57
Dualdrive (Electrical
power steering) ................................ 72
– activation/deactivation ................. 52
EDB system......................................... 68
Electrical power steering
“Dualdrive” ....................................... 72
– activation/deactivation ................. 52
Electrical socket .................................. 55
Engine
– identification code ........................ 180
– marking ........................................... 179
– technical data ................................ 181
Engine compartment (washing)........ 175
Engine coolant fluid level ..................164
Engine coolant temperature gauge . 17
Engine oil .............................................. 163
– consumption .................................. 163
– level check....................................... 163
– specifications ................................. 191
EOBD (system) ................................... 72
ESP system............................................ 69
External lights ...................................... 48
198
WARNING
LIGHTS AND
MESSAGES
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
197-204 Panda New GB 21-06-2007 13:54 Pagina 198