2007 FIAT PANDA change wheel

❒loosen the bolts on the wheel to be re-
placed with the tool E-fig. 4provided;
❒turn handle to partially open the jack;
❒loosen the clamping device B-
fig. 3;
❒take out the tool container Cand take
it near the wheel to be changed;
❒take the space saver spare wheel D;
❒to remove the wheel cap secured by
spring, use the screwdriver provided
levering on the three notches present
on the outer circumference;
fig. 4F0G0695m
128
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCYfig. 3F0G0078m
To change a wheel proceed as follows:
❒Stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely. The
ground should be flat and adequately
firm;
❒ turn the engine off and pull up the hand-
brake;
❒ engage first gear or reverse;
❒lift the luggage compartment mat A-
fig. 2;
fig. 2F0G0171m
123-154 Panda New GB 21-06-2007 13:51 Pagina 128

IMPORTANT Do not use inner tubes
with tubeless tyres. Check the inflation
pressure of the tyres and the spare wheel
regularly.
IMPORTANT You will need to change the
set of bolts if you want to change the type
of wheels fitted (alloy rims instead of steel
rims, and vice versa). You will have to
change the entire set of fastening bolts
with another set of suitably sized bolts and
adopt a specific spare wheel having differ-
ent building characteristics.
You should keep the bolts and spare
wheel in case you decide to use the orig-
inal type of wheel later on. ❒fasten the three other bolts with the
wrench provided;
❒lower the car and remove the jack;
❒fasten bolts completely, working in a
criss-cross fashion as shown in fig. 10.
fig. 10F0G0696m
131
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
When you have finished
❒arrange the space-saver spare wheel D-
fig. 3in the specific compartment in the
boot;
❒insert the partially open jack into the
container Cand force it slightly into its
seat so that it does not vibrate when
the car is moving;
❒ put the tools back into their places in
the container;
❒stow the container complete with tools
on the spare wheel and secure every-
thing with the clamping device B;
❒correctly reposition the boot stiff cov-
er.
123-154 Panda New GB 21-06-2007 13:51 Pagina 131

❒sight inspect the conditions of: engine,
gearbox, transmission, pipes and hoses
(exhaust - fuel - brakes) rubber parts
(boots - sleeves - bushes etc.), fuel and
brake system hoses;
❒check battery charge;
❒visual check on various drive belt con-
ditions;
❒ top up fluid levels (engine coolant,
brakes, windscreen washer, battery,
etc.);
❒ change engine oil;
❒ change engine oil filter;
❒change pollen filter (where provided).
ADDITIONAL CHECKS
Every 1,000 km or before long journeys,
check and top up if required:
❒ engine coolant fluid level;
❒ brake fluid level;
❒battery fluid level;
❒ windscreen washer fluid level;
❒tyre pressure and conditions.
Every 3,000 km check and top up if re-
quired:
❒engine oil level.
You are recommended to use FL Selenia
products designed and produced specifi-
cally for Fiat cars (see table “Capacities”
in section “Technical specifications”).
ANNUAL INSPECTION
SCHEDULE
For cars with an annual mileage of below
20,000 Km (for example about 15,000
Km) the following yearly inspection pro-
gramme is advised:
❒Check tyre conditions/wear and adjust
pressure if required (including the spare
wheel);
❒check lighting system operation (head-
lights, direction indicators, hazard lights,
boot lights, passenger compartment
lights, glovebox light, warning lights,
etc.);
❒check windscreen wiper/washer oper-
ation, adjust nozzle;
❒check windscreen/rear window blade
position/wear;
❒ check front disk brake pad conditions
and wear;
❒check cleanness of locks, bonnet and
boot and lever cleanness and lubrica-
tion;
159
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
155-176 Panda New GB 21-06-2007 13:52 Pagina 159

171
WARNING
LIGHTS AND
MESSAGES
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
RUBBER HOSES
As far as the brake system and fuel rubber
hoses are concerned, carefully follow the
“Service schedule” in this section.
Indeed ozone, high temperatures and pro-
longed lack of fluid in the system may
cause hardening and cracking of the hoses,
with possible leaks. Careful control is
therefore necessary.
❒tyres age even if they are not used
much. Cracks in the tread rubber are
a sign of ageing. In any case, if the tyres
have been on the car for over 6 years,
they should be checked by specialised
personnel, to see if they can still be
used. Also remember to check the
spare wheel;
❒ In the case of replacement, always fit
new tyres, avoiding those of dubious
origin;
❒ If a tyre is changed, also change the in-
flation valve;
❒to allow even wear between the front
and rear tyres, it is advisable to change
them over every 10-15 thousand kilo-
metres, keeping them on the same side
of the car so as not to reverse the di-
rection of rotation.
Remember that road holding
depends also on the correct
tyre inflating pressure.
WARNING
If the pressure is too low the
tyre overheats and this can
cause it serious damage.
WARNING
Do not cross switch the
tyres, moving them from the
right of the car to the left and vice
versa.
WARNING
Never submit alloy rims to
repainting treatments re-
quiring to use temperatures exceed-
ing 150°C. The mechanical properties
of the wheels could be impaired.
WARNING
155-176 Panda New GB 21-06-2007 13:52 Pagina 171

FUEL CAPACITIES (litres)
1.1 1.2 1.3 Multijet
Tank capacity 35 35 35
Reserve 5 5 5
Refuel petrol engines with unleaded petrol with octane rating (RON) no lower than 95 only (EN 228 Specifications)
Refuel diesel engines with diesel fuel for motor vehicles only (EN 590 Specifications)
Fiat Group Automobiles S.p.A. - Quality - Assistenza Tecnica - Ingegneria Assistenziale
Largo Senatore G. Agnelli, 5 - 10040 Volvera - Torino (Italia)
Print N:. 603.81.224 - 07/2007 - 1
stEdition
COLD TYRE INFLATION PRESSURE (bar)
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm.
In any case, check the correct value again when the tyres are cold.
Medium load
Full load
Front
2.0
2.0
2.2
2.2
2.0Rear
1.8
1.8
1.8
1.8
1.8Front
2.2
2.2
2.3
2.3
2.2Rear
2.2
2.2
2.2
2.2
2.2Space-saverspare
wheel
2.8
2.8 Tyre
155/80 R 13 79T
165/65 R 14 79T (*)
155/80 R 13 79T
165/65 R 14 79T (*)
155/80 R 13 79T M+S
165/65 R 14 79T M+SVersions
Petrol
Multijet
Snow tyres
(*) Standard on Emotion versions and optional on Dynamic versions.
ENGINE OIL CHANGE (litres)
1.1 1.2 1.3 Multijet
Engine sump 3.1 2.5 2.85
Engine sump and filter 3.5 2.8 3.0
197-204 Panda New GB 21-06-2007 13:54 Pagina 204