2007 FIAT PANDA Trans

135
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒if at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the near-
est Fiat Dealership.
It is of vital importance to
communicate that the tyre
has been repaired using the quick tyre
repair kit. Hand the instruction
brochure to the personnel charged
with treating the tyre repaired with
the kit.
WARNINGfig. 7F0G0699mfig. 8F0G0676m
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor can be also used just for
restoring pressure. Release cylinder con-
nection A-fig. 8and connect it directly to
the tyre valve fig. 7; in this way the cylin-
der is not connected to compressor and
the sealing fluid will not flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection A-fig. 8;
❒turn counter-clockwise the cylinder to
replace and raise it;
❒fit the new cylinder and turn it clock-
wise;
❒connect connection Ato the cylinder
and fit the transparent tube Binto the
proper space.
123-154 Panda New GB 21-06-2007 13:51 Pagina 135

136
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
WHEN NEEDING
TO CHANGE A BULB
GENERAL INSTRUCTIONS
❒Before changing a bulb check the con-
tacts for oxidation;
❒ Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒Always check headlight aiming after
changing a bulb to ensure they are safe;
❒When a light is not working, check that
the corresponding fuse is intact before
changing a bulb: for the location of fus-
es, refer to paragraph “If a fuse blows”
in this section.
Alterations or repairs to the
electric system not carried
out correctly and without taking into
account the system specifications
may cause failures and the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas, in the case of
breakage they may burst.
WARNING
Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent
bulb is touched with the fin-
gers, its lighting intensity is reduced and
life of the bulb may be compromised.
If touched accidentally, rub the bulb
with a cloth moistened with methylat-
ed spirit and allow to dry.
123-154 Panda New GB 21-06-2007 13:51 Pagina 136

SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒push the transparent cover A-fig. 27
towards car running direction (it is
pressure-fitted);
❒remove connector G-fig. 25;
❒release the bulb holder catch H;
❒remove the burnt bulb I-fig. 26and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
fig. 25F0G0093mfig. 27F0G0095m
fig. 26F0G0094m
140
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the burnt bulb F-fig. 24and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
To replace the main/dipped beam light
bulb, proceed as follows:
❒release clip A-fig. 21and remove cap
B;
fig. 24F0G0092m
123-154 Panda New GB 21-06-2007 13:51 Pagina 140

141
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the transparent cover A-fig.
28from bulb holder (it is pressure-fit-
ted);
❒remove the bulb Band replace it;
❒ refit the lens.
❒loosen cover C-fig. 30and remove the
connector D;
❒release clip E-fig. 31and remove the
bulb F;
❒refit by reversing the above mentioned
operations. FRONT FOG LIGHTS
(where provided)
To change the halogen bulb, proceed as
follows:
❒slacken the two fog light fastening
screws A-fig. 29on the bumper;
❒slacken the two fog light fastening
screws Bunder the bumper;
❒remove the protection including the fog
light and remove the connector;
fig. 29F0G0227mfig. 28F0G0604mfig. 30
TOPOFFON
F0G0228m
fig. 31F0G0229m
123-154 Panda New GB 21-06-2007 13:51 Pagina 141

143
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Number plate light
To change the bulb, proceed as follows:
❒use a screwdriver to remove the re-
taining spring as shown in fig. 35;
fig. 35F0G0099mfig. 36F0G0100m
THIRD STOP LIGHT
To change the bulb, proceed as follows:
❒slacken the two screws A-fig. 37and
remove the whole cover;
❒disconnect connector B-fig. 38and re-
move the light unit;
fig. 37F0G0101m
fig. 38F0G0210m
❒remove the transparent A-fig. 36and
the bulb Bfrom the bulb holder;
❒change the 12V-5W bulb pressure-fit-
ted in the bulb holder;
❒ refit the lens.
123-154 Panda New GB 21-06-2007 13:51 Pagina 143

145
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒open cover B-fig. 41as shown;BOOT LIGHT (where provided)
To change the bulb, proceed as follows:
❒open the tailgate;
❒insert the screwdriver supplied with the
car in the point shown by the arrow
and remove the ceiling light A-fig. 43.
fig. 40F0G0193m
fig. 41F0G0213m
fig. 42F0G0214mfig. 43F0G0102m
❒replace the bulb C-fig. 42releasing the
side contacts, insert the new bulb and
make sure that it is correctly clamped
between the contacts;
❒close the cover and refit the transpar-
ent.
123-154 Panda New GB 21-06-2007 13:51 Pagina 145

146
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IF A FUSE BLOWS
GENERAL fig. 45
The fuse is a protective device for the
electric system: it comes into action (i.e.
it cuts off) mainly due to a fault or im-
proper action on the system.
When a device does not work, check the
efficiency of its fuse: the conductor ele-
ment Amust be intact. If not, replace the
fuse with one of the same amp rating
(same colour).
Bundamaged fuse.
Cfuse with damaged filament.
To facilitate fuse replacement, use the pli-
ers Dhooked to the fusebox on the in-
strument panel left-hand side.
Refer to the tables on the following pages
to identify the protection fuse.
❒open the bulb cover B-fig. 44and re-
place the pressure-fitted bulb C;
❒refit the cover Bon the transparent;
❒refit correctly the light pressing one
side and then the other until the lock-
ing click is heard.
fig. 44F0G0103mfig. 45F0G0087m
Never replace a fuse with
metal wires or anything else.
Never replace a fuse with
another with a higher amp
rating; DANGER OF FIRE.
WARNING
If a general fuse (MEGA-
FUSE, MIDI-FUSE, MAXI-
FUSE) cuts in, do not attempt any re-
pair and contact a Fiat Dealership.
WARNING
If a fuse blows again, contact
a Fiat Dealership.
WARNING
Before replacing a fuse,
make sure the ignition key
has been removed and that all the
other services are switched off and/or
disengaged.
WARNING
123-154 Panda New GB 21-06-2007 13:51 Pagina 146

150
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
10
10
30
30
15
20
20
15F39
F39
F40
F43
F53
F47
F48
F52
Passenger’s compartment fusebox - fig. 47FUSE AMPERE
Telephone
Body-computer control unit
Heated rear window
Windscreen wiper/washer
Windscreen/rear window washer pump
Front left power window
Front right power window
Rear window wiper
30
20
15
15
15
15
7.5
10
7.5
F8
F9
F10
F11
F14
F15
F16
F17
F18
Engine compartment fusebox - fig. 49FUSE AMPERE
Ai conditioner electric fan
Headlight washer
Horn
Secondary services and tachymeter generator
Upper beam
Trailer unit
Electronic injection system and Dualogic transmission unit supply
Electronic injection primary services
Engine control node
123-154 Panda New GB 21-06-2007 13:51 Pagina 150