2007 FIAT PANDA Control

134
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
fig. 4F0G0672mfig. 6F0G0698m
fig. 5F0G0673m
❒check that the compressor switch D-
fig. 4is set at 0 (off), start the engine,
fit plug E-fig. 5into the 12V outlet lo-
cated on the central console and then
turn the compressor on setting the
switch D-fig. 4in position I(on). Inflate
the tyre at the pressure value specified
in paragraph “Inflation pressure” in sec-
tion “Technical Specifications” Check tyre pressure on gauge F-
fig. 4with compressor off to obtain
precise reading;
❒if after 5 minutes it is still impossible
to reach at least 1.5 bar, disengage com-
pressor from valve and current outlet,
then move the car forth for approx. ten
metres in order to distribute the seal-
ing fluid inside the tyre evenly, then re-
peat the inflation operation;
❒If after this operation it is still impossi-
ble after 5 minutes to reach at least 1.8
bar, do not start driving since the tyre
is excessively damaged and the quick
tyre repair kit cannot guarantee suit-
able sealing, contact Fiat Dealership;
❒if reaching the tyre pressure specified
in paragraph “Inflation pressure” in sec-
tion “Technical Specifications”, start
driving immediately;
❒after driving for about 10 minutes stop
and check again the tyre pressure; pull
up the handbrake;
Apply the sticker in a visible
position for the driver to in-
dicate that the tyre has been treat-
ed with the quick tyre repair kit. Dri-
ve carefully especially when corner-
ing. Do not exceed 80 km/h. Avoid
heavy braking and accelerating.
WARNING
If the pressure falls below 1.8
bars, do not drive any fur-
ther: the quick tyre repair kit Fix & Go
automatic cannot guarantee proper
hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
123-154 Panda New GB 21-06-2007 13:51 Pagina 134

135
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒if at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the near-
est Fiat Dealership.
It is of vital importance to
communicate that the tyre
has been repaired using the quick tyre
repair kit. Hand the instruction
brochure to the personnel charged
with treating the tyre repaired with
the kit.
WARNINGfig. 7F0G0699mfig. 8F0G0676m
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor can be also used just for
restoring pressure. Release cylinder con-
nection A-fig. 8and connect it directly to
the tyre valve fig. 7; in this way the cylin-
der is not connected to compressor and
the sealing fluid will not flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection A-fig. 8;
❒turn counter-clockwise the cylinder to
replace and raise it;
❒fit the new cylinder and turn it clock-
wise;
❒connect connection Ato the cylinder
and fit the transparent tube Binto the
proper space.
123-154 Panda New GB 21-06-2007 13:51 Pagina 135

136
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
WHEN NEEDING
TO CHANGE A BULB
GENERAL INSTRUCTIONS
❒Before changing a bulb check the con-
tacts for oxidation;
❒ Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒Always check headlight aiming after
changing a bulb to ensure they are safe;
❒When a light is not working, check that
the corresponding fuse is intact before
changing a bulb: for the location of fus-
es, refer to paragraph “If a fuse blows”
in this section.
Alterations or repairs to the
electric system not carried
out correctly and without taking into
account the system specifications
may cause failures and the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas, in the case of
breakage they may burst.
WARNING
Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent
bulb is touched with the fin-
gers, its lighting intensity is reduced and
life of the bulb may be compromised.
If touched accidentally, rub the bulb
with a cloth moistened with methylat-
ed spirit and allow to dry.
123-154 Panda New GB 21-06-2007 13:51 Pagina 136

137
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
TYPES OF BULBS fig. 20
Various types of bulbs are fitted to your
car:
A All glass bulbs: these are pressed on.
Pull to remove.
B Bayonet type bulbs: press the bulb,
then counterclockwise to remove this
type of bulb from its holder.
C Tubular bulbs: free them from their
contacts to remove.
D Halogen bulbs: to remove the bulb,
release the clip holding the bulb in
place.
E Halogen bulbs: to remove the bulb,
release the clip holding the bulb in
place.
F0G0118mfig. 20
Where possible, it is advisable
to have bulbs changed c/o Fi-
at Dealership. The correct
operation and aiming of the
outer lights are vital to the safety of the
car and its passengers and the subject
of specific laws.
IMPORTANT The headlight inner surface
might be slightly misted: this should not be
considered irregular but a natural phe-
nomenon due to low temperature and the
air humidity level. Misting will disappear as
soon as the headlights are turned on.
Drops inside the headlight mean water in-
filtration: contact Fiat Dealership.
123-154 Panda New GB 21-06-2007 13:51 Pagina 137

138
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
H4
H4
W5W
PY21W
W5W
PY21W
P21/5W
P21W
P21W
C5W
W5W
C5W
H1
W5W60/55
60/55
5
21
5
21
21/5
21
21
5
5
5
55
5D
D
A
B
A
B
B
B
B
C
A
C
E
A
Bulbs Type Power Ref. figure
Main beam
Dipped beam
Front side lights
Front direction indicators
Side direction indicators
Rear direction indicators
Stop/taillights
Reversing light
Rear fog lights
Ceiling light
Boot light
Number plate light
Fog lights
Third stop
123-154 Panda New GB 21-06-2007 13:51 Pagina 138

139
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
To change the direction indicator bulb,
proceed as follows:
❒release clip A-fig. 21and remove cap
B;
❒turn the bulb-holder D-fig. 22and re-
move it (it is pressure-fitted);
IF AN EXTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
fig. 21F0G0089mfig. 22F0G0090m
fig. 23F0G0091m
FRONT LIGHT UNITS
To change the bulb, proceed as follows:
❒release clip A-fig. 21 and remove cap
B;
❒turn the bulb-holder C-fig. 22and re-
move it (it is pressure-fitted);
❒remove the burnt bulb E-fig. 23 and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
123-154 Panda New GB 21-06-2007 13:51 Pagina 139

SIDE DIRECTION INDICATORS
To change the bulb, proceed as follows:
❒push the transparent cover A-fig. 27
towards car running direction (it is
pressure-fitted);
❒remove connector G-fig. 25;
❒release the bulb holder catch H;
❒remove the burnt bulb I-fig. 26and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
fig. 25F0G0093mfig. 27F0G0095m
fig. 26F0G0094m
140
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the burnt bulb F-fig. 24and fit
the new bulb;
❒refit by reversing the above mentioned
operations.
To replace the main/dipped beam light
bulb, proceed as follows:
❒release clip A-fig. 21and remove cap
B;
fig. 24F0G0092m
123-154 Panda New GB 21-06-2007 13:51 Pagina 140

141
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒remove the transparent cover A-fig.
28from bulb holder (it is pressure-fit-
ted);
❒remove the bulb Band replace it;
❒ refit the lens.
❒loosen cover C-fig. 30and remove the
connector D;
❒release clip E-fig. 31and remove the
bulb F;
❒refit by reversing the above mentioned
operations. FRONT FOG LIGHTS
(where provided)
To change the halogen bulb, proceed as
follows:
❒slacken the two fog light fastening
screws A-fig. 29on the bumper;
❒slacken the two fog light fastening
screws Bunder the bumper;
❒remove the protection including the fog
light and remove the connector;
fig. 29F0G0227mfig. 28F0G0604mfig. 30
TOPOFFON
F0G0228m
fig. 31F0G0229m
123-154 Panda New GB 21-06-2007 13:51 Pagina 141