Page 34 of 42
33
QUICK
GUIDE
FUNCTIONS AND
ADJUSTMENTS
RADIO
COMPACT
DISC PLAYER
MP3 CD
PLAYER
CD
CHANGER
INTRODUCTIONSELECTING THE CD CHANGER
To turn on the CD Changer, turn the
sound system on and then press briefly
and repeatedly the SRC button to select
the “CDC” source (CD Changer).
POSSIBLE ERROR
MESSAGES
If the loader does not contain Compact
Discs, the display will show “NO CD”. If
at least one CD is found, it will be played.
If the CD played is illegible, the next CD
will be selected; if there are no other CDs
or if they are also illegible, the display will
show “NO CD” until the sound source
is changed.OPERATION
To play the Compact Discs in the CD
Changer, select “CDC” pressing briefly
and repeatedly the SRC button.
When listening to a Compact Disc for the
first time after inserting the CD loader,
playing starts from the first track on the
first disc available in the loader.
While playing the display shows the num-
ber of the track being played (e.g.
“TRACK 12” = twelfth track), the play-
ing time elapsed from the start of the track
(e.g. “11:10” = 11 minutes and 10 sec-
onds) and the number of the Compact
Disc selected (e.g. “CDC3” = third CD)
depending on the function selected in the
menu.
C C
D D
C C
H H
A A
N N
G G
E E
R R
INTRODUCTION
This section only describes CD Changer
(where provided) operation variants: as
concerns sound system operation, refer
to section “FUNCTIONS AND ADJUST-
MENTS”.
Should the CD Changer pre-
arrangement be requested it will be
provided with the necessary wiring
for correct CD Changer Blaupunkt
function.
Cable end will be easy to identify by
lifting the covering carpet in the boot
near the right wheel housing.
IMPORTANT If the Blue&Me™or the
Blue&Me™ Navare present in the car,
no type of CD Changer can be installed.
Page 35 of 42
QUICK
GUIDE
34
FUNCTIONS AND
ADJUSTMENTS
RADIO
COMPACT
DISC PLAYER
MP3 CD
PLAYER
CD
CHANGER
INTRODUCTION
SELECTING A CD
Press button 1 CD + to select the next
CD and button 2 CD – to select the pre-
vious CD.
If the loader does not contain a disc in the
position selected, the display shows “NO
CD”, and the next CD will be played au-
tomatically.
TRACK SELECTION
(forward/backward)
Press briefly button Íto play the next
track contained in the Compact Disc be-
ing played.
Press briefly button Èto play the previ-
ous track contained in the Compact Disc
being played.FAST FORWARD/BACKWARD
Keep button Ípressed to move the track
selected fast forward and keep button È
pressed to move it fast backward. Fast for-
ward/backward is stopped when the but-
ton is released.
SCAN FUNCTION
(scanning CD tracks)
With this function it is possible to listen to
all the tracks contained in the CD select-
ed.
Keep button SCAN pressed to play the
first 10 seconds of each track contained in
the CD. While playing the track, the dis-
play will alternately show the CD Chang-
er function selected (CD Changer name,
track playing time and number of the track
being played) and the word “SCAN” (e.g.:
“CDC3 SCAN TK12 0.04”)
If the Scan function is on, Repeat and Mix
functions are turned off.The scanning sequence is the following:
– from the track being played up to the
last one on the CD
– from the first track up to the one being
played when the scan function was start-
ed.
The Scan function is interrupted in the fol-
lowing cases:
– turning the sound system off
– pressing the SCAN button again to con-
tinue listening to the track being played
– pressing Íor Èthereby moving to the
next or previous track
– pressing a preset button
– changing the sound source
– pressing the
RDSMENU button.
If the Scan function is not interrupted, at
the end it will continue playing the track
played before scanning was started.
Page 36 of 42
35
QUICK
GUIDE
FUNCTIONS AND
ADJUSTMENTS
RADIO
COMPACT
DISC PLAYER
MP3 CD
PLAYER
CD
CHANGER
INTRODUCTION
PAUSE FUNCTION
To pause the CD player, press briefly the
button MUTE. The display will show
“CDC MUTE”.
To resume track playing, press button
MUTE again.
The pause function is automatically can-
celled when changing the sound source.
TRACK REPEAT FUNCTION
(track repeat)
Press briefly the preset button 5
RPTto lis-
ten repeatedly to the last track played: the
display will show “CDC REPEAT
TRACK”.
Press the preset button 5
RPTagain to turn
off the repeat function: the display will
show “CD REPEAT OFF”.
Changing the sound source, the function
is turned off.
IMPORTANT When the repeat function
is on, the SCAN and MIX functions are
turned off.RANDOM FUNCTION
(random track playing)
To start random playing of tracks on the
Compact Disc selected, press the preset
button 6
RND.
A new track will be played and the dis-
play will show “CDC RANDOM DISK”.
To start random playing of all the CDs
contained in the CD Changer, press again
button 6
RND; the display will show “CDC
RANDOM PACK”.
Press the preset button 6
RNDa third time
to turn the function off: the display will
show “CDC RANDOM OFF”. STOPPING CD PLAYING
Press button ˚or button SRC to return
to the tuner mode.
Page 38 of 42
ENTERING THE SECRET CODE
OF THE CD CHANGER
Should the control code between the
sound system and the CD Changer be not
recognised, to restore CD Changer regu-
lar operation the four-digit secret code
must be entered manually.
When entering the secret code, the dis-
play shows: “CDC M --CODE ----”.
The secret code comprises four figures,
each corresponding to one of the dashes
and it is different for each CD Changer.
To enter the first digit of the code, press
the corresponding button of the preset
stations (from 1 to 4). Press repeatedly the
preset buttons 1-4 to enter the secret
code digits (from 0 to 9).To confirm the required digit press 5 RPT.
If the code has been entered properly, the
radio and the CD Changer start to work
regularly.
Otherwise try to enter the secret code a
second and even a third time if required.
After the third negative attempt, the radio
sets in “stand-by” for about 1 hour before
enabling other three attempts.
