2007 DODGE SPRINTER service interval

3 Introduction
\3 Environmental protection
In this manual, whenever you see instruc-
tions to discard materials, you should first
attempt to reclaim and recycle them. To
preserve our environment, follow appropri-
ate environmental rules and regulations
when disposing of materials.
Environmental note
H
DaimlerChrysler’s declared policy is one of
comprehensive environmental protection.
The objectives are for the natural resources
which form the basis of our existence on this
planet to be used sparingly and in a manner
which takes the requirements of both nature
and humanity into account.
You too can contribute to environmental
protection by operating your vehicle in an
environmentally-responsible manner.
Fuel consumption and engine, transmission,
brake and tire wear depend on the two fol-
lowing factors:
\4Operating conditions of your vehicle
\4Your personal driving style
You can influence both factors.
Observe the following notes:
Operating conditions
\4Avoid driving short distances as this in-
creases fuel consumption.
\4Make sure that the tire pressures are al-
ways correct.
\4Do not carry any unnecessary weight
in / on the vehicle.
\4Keep an eye on the vehicle’s fuel con-
sumption.
\4Remove roof racks once you no longer
need them.
\4A regularly serviced vehicle will contrib-
ute to environmental protection. You
should therefore adhere to the specified
service intervals.
\4Always have maintenance work carried
out at an authorized Sprinter Dealer.
Personal driving style
\4Do not depress the accelerator pedal
when starting the engine.
\4Do not warm up the engine when the ve-
hicle is stationary.
\4Adopt an anticipatory style of driving
and keep a sufficient distance from oth-
er vehicles.
\4Avoid frequent, sudden acceleration.
\4Switch off the engine in stationary traf-
fic.
Environmental concerns and recom-
mendations

130 Controls in detailTempmatic
3
Tempmatic is only operational while the
engine is running. You can use Tempmatic
to regulate or control the temperature au-
tomatically. The vehicle is either heated or
cooled, depending on the temperature se-
lected and the outside temperature.
The combination filter removes most dust
particles, pollen and unpleasant odors
from the outside air.
The interval for replacing the filter depends
on environmental factors, e.g. high air pol-
lution. The interval may be shorter than
that indicated in the Service Booklet.
Function
Page
1
Side window defroster
vents
135
2
Thumbwheel for air vents
3
Side air vents
4
Thumbwheel for side air
vents and defroster vents
135
5
Swiveling center air vents
6
Thumbwheel for center air
vents
7
Control panel\4Tempmatic
\4Rear heating/rear cool-
ing*
131
136
8
Switch\4Rear window heating*
\4Windshield heating*
128
127
9
Auxiliary heating switch*
Heater booster switch*
140
137
iCondensation may collect under the
vehicle while Tempmatic is in opera-
tion.
Warning
G
Follow the settings recommended on the
following pages for heating or cooling. The
windows could otherwise fog up. As a result,
you could be distracted from road and traffic
conditions and cause an accident.Warning
G
Air flowing out of the air vents in the footwell
when Tempmatic is in operation may be very
hot or very cold. There is therefore a risk of
frostbite or burns to bare skin in the imme-
diate proximity of these outlets. Keep bare
skin away from these air outlets. If neces-
sary, direct the airflow into a different area
of the vehicle interior using the air distribu-
tion control.

355 *Technical data
Service products and capacities
6
\3 Service products and capacitiesService products are:
\4fuels
\4lubricants (e.g. engine oils, transmis-
sion oils, hydraulic fluids, greases)
\4antifreeze additives, coolant
\4brake fluid
Service products are tested for suitability
in our assemblies. Approved service prod-
ucts meet the highest quality standards.
For this reason, only use service products
that have been approved for your vehicle.
This is an important condition for warranty
claims to be upheld. Information about ap-
proved service products is available from
all authorized Sprinter Dealers.
You will find details about windshield
washer fluid in the “Operation” section
(\2page 193).
It is neither necessary nor permissible to
mix special additives with approved ser-
vice products (except for approved fuel ad-
ditives). Therefore, special additives must
not be mixed with fuels or lubricants. The properties of the service products could be
adversely affected by special additives and
result in damage to the assemblies.
The vehicle operator is responsible at all
times for any use of special additives. The
use of special additives may result in a lim-
itation or an invalidation of your warranty
entitlement.
Warning
G
Failure to use fluids and lubricants which
meet the standards and specifications de-
scribed in this booklet or failure to adhere to
the specified replacement intervals may re-
sult in damage to safety/ and/or emissions-
related systems of your vehicle, such as the
brake system, which could cause an acci-
dent and/or serious injury to you and oth-
ers.
Use only fluids and lubricants meeting the
standards and specifications and adhere to
specified replacement intervals.
!
CAUTION
Damage caused by the use of non-ap-
proved service products is not covered
by the Sprinter warranty.
Warning
G
Service products constitute a health hazard.
They contain toxic and highly corrosive con-
stituents.
For this reason, bear the following points in
mind to avoid injury to yourself and others:
\4Do not inhale fumes. Make sure that en-
closed spaces are adequately ventilated
to prevent poisoning.
\4Service products must not come into
contact with the skin, eyes or clothing. If
contact is made with a service product,
clean the affected areas of skin with wa-
ter and soap to prevent burns and other
injuries.
\2\2

362 *Technical dataService products and capacities
6
Coolants, lubricants, etc.
Service
interval
Product name/product number
MB
sheet
MS-
No.
1
Air conditioning
The air conditioning system of your vehicle contains R-134a, a refrigerant that does not deplete the ozone layer in the upper atmo-
sphere.Refrigerant R-134a
—
Refrigerant R-134a
361.0
Automatic transmissionAutomatic transmission fluid
10 years
60,000 mi
(96,000 km)
MOPAR
® 05127382AB
Shell ATF 3403
Shell ATF 3353
236.10
236.12
BrakesUse brake fluid approved for DaimlerChrysler standard MB 331.0 and/or DaimlerChrysler material standard MS-9971, brake fluid certified
to DOT 4 Plus standards, that also maintains a minimum dry boiling point (ERBP) of 500 °F (260°C), a minimum wet boiling point (WERBP)
of 356 °F (180 °C) and a maximum viscosity of 1500 mm
2/s, conforming to FMVSS 116 and ISO 4925.
Brake fluid
2 years
2
Intac B026E Dry boiling point: 500°F (260°C)
Wet boiling point: 356°F (180°C)
MOPAR
® MS-9971 Part No. 04549625AC or equivalent
331.0
9971
1 DaimlerChrysler Material Standard-No.
2 Over the course of a brake fluid’s service life, its boiling point falls due to the continuous absorption of moisture from the atmosphere. If the boiling point of the
brake fluid is too low, vapor pockets may form in the brake system when the brakes are applied hard (e.g. when driving on long downhill stretches). This has a det-
rimental effect on braking efficiency, which could increase the stopping distance. This increases the risk of an accident. Have the brake fluid renewed every 2 years.

363 *Technical data
Service products and capacities
6
Service interval
Product name/product number
MB
sheet
MS-
No.
1
Engine cooling system
The use of aluminum components in Sprinter engines requires that anticorrosive/antifreeze specifically formulated to protect aluminum
parts be used. The factory-approved service products are suitable for Sprinter engines and can be mixed with the original anticorrosion/
antifreeze filled at factory.
The cooling system design and anticorrosion/antifreeze agent used stipulate the replacement interval for the coolant solution in your ve-
hicle. Please observe the replacement interval specified in the Service Booklet for your vehicle.
Failure to use MB 325.0 anticorrosion/antifreeze and/or equivalent to DaimlerChrysler material standard MS-9769 and/or failure to ad-
here to the specified replacement interval may result in a significantly shortened service life.
For coolant composition and water quality, contact your authorized Sprinter Dealer.Coolant, anticorrosion/antifreeze
fluid
1st interval:
15 years or
180,000 mi
(288,000 km)
2 Sub-
sequent intervals: 5
years or 100,000
mi (160,000 km)
EURO Peak Coolant/Antifreeze
OLD WORLD INDUSTRIES
325.0
Zerex G05, The Valvoline Company
325.0
Zerex G48, The Valvoline Company
325.0
Glysantin G05, BASF AG
MOPAR
® Part No. 05066386AA, or equivalent
325.0
EngineEngine oil for gasoline engine M272
1 year or 10,000 mi
(16,000 km)
see “Engine oils” (page 350)
229.31, 229.3
229.51, 229.5
Engine oil for diesel engine OM642
2 years or 10,000
mi (16,000 km)
See “Engine oils” (page 350)
228.51
229.31
229.51
1 DaimlerChrysler Material Standard-No.
2 Follow the interval, time or mileage, that occurs first.

364 *Technical dataService products and capacities
6
Service interval
Product name/product number
MB
sheet
MS-
No.
1
Power steering
Power steering, no fluid service required.Power steering fluid
—
Mobil ATF+4, Exxon Mobil Corporation, or equiva-
lent
236.3
9602
MOPAR
® Part No. 05013457AA, or equivalent
–
Rear axleGear oil
10 years or
180,000 mi
(288,000 km)
2
BP Energear Hyep DC 80W-90
Mobil Delvac Synthetic Gear Oil 75W-90
235.20
235.8
8985
MOPAR
® Part No. 04874469
3
–
1 DaimlerChrysler Material Standard-No.
2 Follow the interval, time or mileage, that occurs first.
3 Synthetic automotive gear lubricant without fricition modifier.