2007 DODGE MAGNUM hood release

TO OPEN AND CLOSE THE HOOD
Two latches must be released to open the hood. First, pull
the hood release lever located under the left side of the
instrument panel.
Next, move to the outside of the vehicle and push the
safety catch to the left. The safety catch is located under
the center front edge of the hood.Use the hood prop rod (if equipped) to secure the hood in
the open position.
To prevent possible damage, do not slam the hood to
close it. Lower the hood until it is open approximately 6
inches (15 cm), and then drop it. This should secure both
latches. Never drive your vehicle unless the hood is fully
closed, with both latches engaged.
Hood Release Lever
Hood Safety Catch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95
3

INSTRUMENT PANEL AND CONTROLS
1 — Air Outlet 6 — Glove Box 11 — Ash Tray*
2 — Instrument Cluster 7 — Radio 12 — Ignition Switch
3 — Rear Wiper/Washer Switch 8 — Climate Control 13 — Hood Release
4 — Hazard Switch 9 — Heated Seat Switch* 14 — Headlight Switch
5 — Electronic Stability Program Off But-
ton* / Traction Control System Off Button*10 — Power Outlet * If EquippedUNDERSTANDING YOUR INSTRUMENT PANEL 137
4

surfaces. Refer to “Fluids, Lubricants, and Genuine
Parts” in this section for the correct fluid type.
Front & Rear Suspension Ball Joints
The suspension ball joints should be inspected for exter-
nal leakage or damage when other maintenance is per-
formed.
Steering Linkage
The tie rod end ball joints should be inspected for
external leakage or damage when other maintenance is
performed.
Body Lubrication
Locks and all body pivot points, including seat tracks,
door hinges, liftgate hinges, and hood hinges, should be
lubricated periodically to assure quiet, easy operation
and to protect against rust and wear. Prior to the appli-
cation of any lubricant, the parts concerned should be
wiped clean to remove dust and grit; after lubricating
excess oil and grease should be removed. Particular
attention should also be given to hood latching compo-
nents to insure proper function. When performing other
underhood services, the hood latch, release mechanism,
and safety catch should be cleaned and lubricated.The external lock cylinders should be lubricated twice a
year, preferably in the fall and spring. Apply a small
amount of a high quality lubricant such as MoparLock
Cylinder Lubricant or equivalent directly into the lock
cylinder.
Wiper Blades
Clean the rubber edges of the wiper blades and the
windshield and rear window periodically with a sponge
or soft cloth and a mild nonabrasive cleaner. This will
remove accumulations of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield or rear window.
Avoid using the wiper blades to remove frost or ice from
the windshield or rear window. Keep the blade rubber
out of contact with petroleum products such as engine
oil, gasoline, etc.
320 MAINTAINING YOUR VEHICLE

Heater, Engine Block.................... 211
High Beam/Low Beam Select (Dimmer) Switch . 99
Hitches
TrailerTowing ....................... 273
Holder,Cup ........................... 121
HomeLink(Garage Door Opener) Transmitter . 110
Hood Release.......................... 95
Hoses............................... 327
Ignition............................... 11
Key ................................ 11
Ignition Key Removal.................... 11
IlluminatedEntry ....................... 17
Immobilizer (Sentry Key).................. 13
Infant Restraint......................... 51
Inflation Pressure Tires................... 145
Information Center, Vehicle............... 148
Inside Rearview Mirror................... 67
Instrument Cluster................138,139,140
Instrument Panel and Controls............. 137
Instrument Panel Lens Cleaning............ 335
Interior Appearance Care................. 334
Interior Fuses.......................... 337InteriorLights ......................... 100
Intermittent Wipers (Delay Wipers).......102,201
Introduction............................ 4
Jack Location.......................... 287
Jack Operation......................... 289
Jacking Instructions..................... 289
Jump Starting......................... 294
Key, Programming....................... 14
Key, Replacement....................... 14
Key, Sentry (Immobilizer).................. 13
Key-In Reminder........................ 12
Keyless Entry System..................... 17
Keys................................. 11
Knee Bolster........................... 41
Lane Change and Turn Signals.............. 99
Lap/Shoulder Belts...................... 33
LATCH (Lower Anchors and Tether for
CHildren) ........................... 54,55
LatchPlate ............................ 34
Latches............................... 61
388 INDEX