2007 DODGE GRAND CARAVAN ECU

FACING TO THE REAR IN A VEHICLE EQUIPPED
WITH THE REAR SEAT DELETE FEATURE (Com-
mercial Vehicles Only). When a convertible seat is
properly installed forward facing, the vehicle seat
should be adjusted to the rear most position.
• Children more than 40 lbs (18 kg) should be secured in
the passenger seat in a child restraint or belt-
positioning booster seat with the seat adjusted to the
rear most position . Older children who do not use
child restraints or belt-positioning booster seats
should ride properly buckled in the passenger seat
with the seat adjusted to the rear most position. Never
allow children to slide the shoulder belt behind them
or under their arm.
Tether Installation For Commercial Vehicles With
Rear Seat Delete
To secure the child restraint upper tether strap to the
vehicle, follow the instructions shown: 1. Locate the child restraint tether anchor on the floor
just behind the front passenger seat.
Tether Anchor LocationTHINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85
2

▫ To Accelerate For Passing ...............166

Overhead Console — If Equipped ...........167
▫ Courtesy/Reading Lights ................168
▫ Sunglass Storage ......................168
▫ Compass/Temperature Display ...........168
▫ Mini-Trip Computer ...................171
▫ Electronic Vehicle Information Center (EVIC) — If
Equipped ...........................172
▫ Customer Programmable Features —
If Equipped .........................173

Garage Door Opener — If Equipped .........177
▫ Programming HomeLink ................178
▫ Canadian Programming/Gate Programming . . 181
▫ Using HomeLink .....................181 ▫ Erasing HomeLink Buttons ..............181
▫ Reprogramming a Single HomeLink Button . . . 182
▫ Security ............................182

Power Sunroof — If Equipped .............183
▫ Express Open Feature ..................183
▫ Wind Buffeting .......................184
▫ Sunroof Maintenance ...................185

Electrical Power Outlets — If Equipped .......185
▫ Electrical Outlet Use With Engine Off .......186

Convenience Tray Drawer And Cup Holders . . . 187
▫ Instrument Panel Cup Holders ............187
▫ Convenience Tray And Optional Smoker’s Package
Kit................................18894 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Next, push to the left the safety catch located under the
front edge of the hood, near the center.
Use the hood prop rod to secure the hood in the open
position.
To prevent possible damage, do not slam the hood to
close it. Lower the hood until it is open approximately 30 cm (12 inches) and then drop it. This should secure both
latches. Never drive your vehicle unless the hood is fully
closed, with both latches engaged.
WARNING!If the hood is not fully latched, it could fly up when
the vehicle is moving and block your forward vision.
You could have a collision. Be sure all hood latches
are fully latched before driving.
LIGHTS
All of the lights, except the hazard warning lights, are
controlled by switches to the left of the steering column
on the instrument panel.Hood Safety Catch150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: To program the remaining two HomeLink but-
tons, begin with  Programming  Step Two. Do not repeat
Step One.
NOTE: If your hand-held transmitter appears to pro-
gram the universal transceiver, but your garage door
does not operate using the transmitter and your garage
door opener was manufactured after 1995, your garage
door opener may have a multiple security code system
(rolling code system). If your garage door is the “rolling
code” type, please proceed to the heading “Program-
ming A Rolling Code System.”
Programming A Rolling Code System
1. At the garage door opener receiver (motor-head unit)
in the garage, locate the  learn  or  smart  button. This
can usually be found where the hanging antenna wire is
attached to the motor-head unit. 2. Firmly press and release the  learn  or  smart  button.
(The name and color of the button may vary by manu-
facturer.)
NOTE: There are 30 seconds in which to initiate Step
Three.
3. Return to the vehicle and firmly press, hold for two
seconds and release the programmed HomeLink button.
Repeat the  press/hold/release  sequence a second time,
and, depending on the brand of the garage door opener
(or other rolling code equipped device), repeat this
sequence a third time to complete the programming.
HomeLink should now activate your rolling code
equipped device.
NOTE: To program the remaining two HomeLink but-
tons, begin with  Programming  Step Two. Do not repeat
Step One . For questions or comments, please contact
HomeLink at www.homelink.com or 1-800-355-3515 .180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Canadian Programming/Gate Programming
Canadian radio-frequency laws require transmitter sig-
nals to  time-out  (or quit) after several seconds of
transmission which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed to  time-out  in the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using the  Program-
ming  procedures (regardless of where you live), replace
 Programming HomeLink  Step Three with the follow-
ing:
NOTE: If programming a garage door opener or gate
operator, it is advised to unplug the device during the
 cycling  process to prevent possible overheating.
3. Continue to press and hold the HomeLink button
while you press and release every two seconds  cycle 
your hand-held transmitter until the frequency signal has successfully been accepted by HomeLink. (The indicator
light will flash slowly and then rapidly.) Proceed with
 Programming  Step Four to complete.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). For convenience, the hand-held transmitter of the
device may also be used at any time. In the event that
there are still programming difficulties or questions,
contact HomeLink at: www.homelink.com or 1-800-355-
3515 .
Erasing HomeLink Buttons
To erase programming from the three buttons (individual
buttons cannot be erased but can be  reprogrammed  -
note below), follow the step noted: UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181
3

• Press and hold the two outer HomeLink buttons until
the indicator light begins to flash-after 20 seconds.
Release both buttons. Do not hold for longer that 30
seconds. HomeLink is now in the train (or learning)
mode and can be programmed at any time beginning
with  Programming  - Step Two.
Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink
button previously trained, follow these steps:
1. Press and hold the desired HomeLink button. Do
NOT release the button.
2. The indicator light will begin to flash after 20 seconds.
Without releasing the HomeLink button, proceed with
 Programming  Step Two.
For questions or comments, contact HomeLink at:
www.homelink.com or 1-800-355-3515 . Security
If you sell your vehicle, be sure to erase the frequencies
by following the “Erasing HomeLink Buttons” instruc-
tions in this section.
This device complies with part 15 of FCC rules and with
RSS-210 of Industry Canada. Operation is subject to the
following conditions:
• This device may not cause harmful interference.
• This device must accept any interference that may be
received including interference that may cause undes-
ired operation.
NOTE: Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
HomeLink  is a trademark owned by Johnson Controls,
Inc.182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To close the sunroof, hold the switch in the forward
position. Again, any release of the switch will stop the
movement and the sunroof will remain in a partial open
condition until the switch is pushed forward again.
The sunshade can be opened manually. It will also open
as the sunroof opens. The sunshade cannot be closed if
the sunroof is open.
WARNING!NEVER leave children alone in a vehicle. Occupants,
particularly unattended children, can become en-
trapped by the power sunroof while operating the
power sunroof switch. Such entrapment may result
in serious injury or death. Don’t leave the keys in the
ignition. A child could operate power windows,
other controls, or move the vehicle WARNING!In an accident, there is a greater risk of being thrown
from a vehicle with an open sunroof. You could also
be seriously injured or killed. Always fasten your
seat belt properly and make sure all passengers are
properly secured too.
Do not allow small children to operate the sunroof.
Never allow fingers or other body parts, or any
object to project through the sunroof opening. Injury
may result.
Wind Buffeting
Wind buffeting can be described as the perception of
pressure on the ears or a helicopter type sound in the
ears. Your vehicle may exhibit wind buffeting with the
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the buffeting occurs with184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To move the cross bars, loosen the thumb screws located
at the upper edge of each cross bar approximately six
turns, then move the cross bar to the desired position,
keeping the crossbars parallel to the rack frame. Once the
cross bar is in place, retighten the thumb screws to lock
the cross bar into position.
Attempt to move the crossbar again to ensure that it has
properly locked into position.
NOTE: To help control wind noise when installing the
cross bars make sure that the arrows marked on the front
side of the cross bars are facing the front of the vehicle.
Also, when the cross bars are not in use the notch on the
cross bars should be aligned with the arrows on the side
rails. This will help reduce the amount of wind noise
when the crossbars are not in use.
The tie down holes on the cross bar ends should always
be used to tie down the load. Check the straps frequently
to be sure that the load remains securely attached. CAUTION!• Crossbars should remain equally spaced or parallel
at any luggage rack position for proper function.
Noncompliance could result in damage to the lug-
gage rack, cargo and/or vehicle.
• To avoid damage to the roof rack and vehicle, do
not exceed the maximum roof rack load capacity of
150 lbs (68 kg). Always distribute heavy loads as
evenly as possible and secure the load appropri-
ately.
• Long loads which extend over the windshield, such
as wood panels or surfboards, or loads with large
frontal area should be secured to both the front and
rear of the vehicle.
• Travel at reduced speeds and turn corners carefully
when carrying large or heavy loads on the roof
rack. Wind forces, due to natural causes or nearby
truck traffic, can add sudden upward lift to loads.
This is especially true on large flat loads and may
result in damage to the cargo or your vehicle.200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE