2007 CITROEN C4 ECU
[x] Cancel search: ECUPage 128 of 279
124
X
C H E C K S
BONNET
Protects the components of the engine and provides access for checking levels.
Opening
Push the exterior control B to the
left and raise the bonnet.
Unclip the strut C from its housing.
Fix the strut in the notch to hold
the bonnet open. Closing
Take the strut out of the support
notch.
Clip the strut in its housing.
Lower the bonnet then slam it
fi r m l y a t t h e e n d o f i t s t r a v e l .
Pull on the bonnet to check that
it is secured correctly.
The location of the interior control
prevents opening of the bonnet
while the driver's door is closed.
This operation must only be carried
out when the vehicle is stationary.
Avoid opening the bonnet in strong
winds.
Pull the interior control A , located
under the dashboard, to the right.
Page 139 of 279
134
XI
P R A C T I C A L I N F O R M A T I O N
R e fi t t i n g t h e w h e e l Dimension of the spare wheel
I f y o u r s p a r e w h e e l i s o f d i f f e r e n t
dimensions to those on the vehicle
( i d e n t i fi e d b y a l a b e l ) , i t i s e s s e n t i a l
t o u s e i t o n l y o n a t e m p o r a r y b a s i s ,
to drive not above 50 mph (80 km/h)
a n d t o h a v e t h e o r i g i n a l w h e e l r e fi t -
t e d a s s o o n a s p o s s i b l e .
Switch on your hazard
warning lamps.
It is imperative to ensure
that the occupants get out of the
vehicle and wait in a safe location.
Never get underneath the vehi-
cle if it is supported only by the
jack; use an axle stand.
T h e j a c k i s d e s i g n e d s p e c i fi c a l l y
for your vehicle, do not use it for
other applications.
R e fi t t h e r e p a i r e d o r i g i n a l w h e e l
as soon as possible.
W i t h a s p a r e w h e e l fi t t e d , d r i v e
with caution.
The wheel should be correctly
p o s i t i o n e d fl a t i n t h e c e n t r e o f
its well. Light alloy wheels
I f y o u r v e h i c l e i s e q u i p p e d w i t h
l i g h t a l l o y w h e e l s a n d a s t e e l s p a r e
w h e e l , t h e n i f fi t t i n g t h e l a t t e r i t i s
normal to note that the heads of the
wheel bolts do not come to bear on
t h e w h e e l r i m .
The steel spare wheel is secured
b y t h e c o n i c a l t a p e r i n g o f t h e w h e e l
b o l t s ’ s h a f t s , s e e d i a g r a m .
W h e n r e fi t t i n g t h e l i g h t a l l o y w h e e l ,
ensure that the wheel bolt heads are
i n u n d a m a g e d c o n d i t i o n .
R e fi t t h e w h e e l i n p l a c e .
U n d o t h e y e l l o w c e n t r a l s c r e w b y
a few turns, then position it at the
c e n t r e o f t h e w h e e l .
D o u p t h e c e n t r a l s c r e w u n t i l t i g h t
s o t h a t t h e w h e e l i s s e c u r e l y r e -
t a i n e d i n p l a c e .
Page 159 of 279
153
XI
P R A C T I C A L I N F O R M A T I O N
BATTERY
P r o c e d u r e f o r c h a r g i n g y o u r b a t t e r y
w h e n i t i s fl a t o r f o r s t a r t i n g t h e e n -
g i n e u s i n g a n o t h e r b a t t e r y .
Access to the battery
T h e b a t t e r y i s l o c a t e d u n d e r t h e b o n n e t .
To gain access to it:
open the bonnet using the inte-
rior lever, then the exterior lever,
secure the bonnet strut,
remove the plastic cover to gain
access to the two terminals,
unclip the fuse box to remove
t h e b a t t e r y , i f n e c e s s a r y . Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e
v e h i c l e .
Follow the instructions for use
p r o v i d e d b y t h e m a n u f a c t u r e r o f
t h e c h a r g e r .
Reconnect starting with the neg-
a t i v e t e r m i n a l ( - ) .
Check that the terminals and
c o n n e c t o r s a r e c l e a n . I f t h e y a r e
covered with sulphate (whitish or
greenish deposit), remove them
a n d c l e a n t h e m .
Starting using another
battery
The batteries contain harm-
ful substances such as sul-
p h u r i c a c i d a n d l e a d . T h e y
must be disposed of in accordance
with regulations and must not, in
a n y c i r c u m s t a n c e s , b e d i s c a r d e d
w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
It is advisable to disconnect the
b a t t e r y i f t h e v e h i c l e i s t o b e l e f t u n -
u s e d f o r m o r e t h a n o n e m o n t h .
Connect the red cable to the
p o s i t i v e t e r m i n a l ( + ) o f t h e fl a t
b a t t e r y A , then to the positive ter-
m i n a l ( + ) o f t h e s l a v e b a t t e r y B .
Connect one end of the green or
black cable to the negative ter-
m i n a l ( - ) o f t h e s l a v e b a t t e r y B .
Operate the starter, let the en-
g i n e r u n .
Wait until the engine returns to
i d l e a n d d i s c o n n e c t t h e c a b l e s .
Page 272 of 279
84
VI
F I T T I N G S
REAR ARMREST
Comfort and storage device for the
rear passengers.
Lower the rear armrest for a
more comfortable position.
Raise the cover to gain access
to its storage compartment.
This has a storage tray, two can hol-
ders and two pen holders.
LUGGAGE SECURING RINGS
U s e t h e 2 r e a r s i d e fi x i n g s a n d
the 4 securing rings on the boot
fl o o r t o s e c u r e y o u r l u g g a g e .
For safety reasons in the event of
sharp braking, you are advised to
p l a c e h e a v y o b j e c t s o n t h e fl o o r a s
close as possible to the back of the
rear seat.
Page 274 of 279
134
XI
P R A C T I C A L I N F O R M A T I O N
R e fi t t i n g t h e w h e e l Dimension of the spare wheel
I f y o u r s p a r e w h e e l i s o f d i f f e r e n t
dimensions to those on the vehicle
( i d e n t i fi e d b y a l a b e l ) , i t i s e s s e n t i a l
t o u s e i t o n l y o n a t e m p o r a r y b a s i s ,
to drive not above 50 mph (80 km/h)
a n d t o h a v e t h e o r i g i n a l w h e e l r e fi t -
t e d a s s o o n a s p o s s i b l e .
Switch on your hazard
warning lamps.
It is imperative to ensure
that the occupants get out of the
vehicle and wait in a safe location.
Never get underneath the vehi-
cle if it is supported only by the
jack; use an axle stand.
T h e j a c k i s d e s i g n e d s p e c i fi c a l l y
for your vehicle, do not use it for
other applications.
R e fi t t h e r e p a i r e d o r i g i n a l w h e e l
as soon as possible.
W i t h a s p a r e w h e e l fi t t e d , d r i v e
with caution.
The wheel should be correctly
p o s i t i o n e d fl a t i n t h e c e n t r e o f
its well. Aluminium wheels
I f y o u r v e h i c l e i s e q u i p p e d w i t h a l u -
minium wheels and a steel spare
w h e e l , t h e n i f fi t t i n g t h e l a t t e r i t i s
normal to note that the heads of the
wheel bolts do not come to bear on
t h e w h e e l r i m .
The steel spare wheel is secured
b y t h e c o n i c a l t a p e r i n g o f t h e w h e e l
b o l t s ’ s h a f t s , s e e d i a g r a m .
W h e n r e fi t t i n g t h e a l u m i n i u m w h e e l ,
ensure that the wheel bolt heads are
i n u n d a m a g e d c o n d i t i o n .
R e fi t t h e w h e e l i n p l a c e .
U n d o t h e y e l l o w c e n t r a l s c r e w b y
a few turns, then position it at the
c e n t r e o f t h e w h e e l .
D o u p t h e c e n t r a l s c r e w u n t i l t i g h t
s o t h a t t h e w h e e l i s s e c u r e l y r e -
t a i n e d i n p l a c e .