2007 CITROEN C2 DAG wheel
[x] Cancel search: wheelPage 122 of 191
A
1 2 1
V
C H A N G I N G A W H E E L
T h e j a c k i s s p e c i fi c t o y o u r v e h i c l e , d o n o t u s e i t f o r a n y o t h e r purposes.
With a spare wheel, drive cautiously.
Access to the spare wheel
Open the lower tailgate.
Remove the blank A with the aid of the ignition key, to insert the exten-sion for the wheelbrace.
Slacken the spare wheel carrier screw.
Lift the carrier to release the retain-ing hook, then disengage it.
To reposition the spare wheel
Having repositioned the jack and its handle in its protection box in the wheel, slide the wheel into the carrier.
Lift the carrier to secure it in the safety hook.
Retighten the screw from inside the boot compartment.
Stow the wheelbrace and exten-sion.
Reposition the blank A.
Tyre pressures
This is indicated on the label on the f r o n t d o o r p i l l a r . S e e “ V e h i c l e i d e n - t i fi c a t i o n ” a n d “ U s e r P r e c a u t i o n s ” .
ADVICE
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e type of wheel.
If the type of wheel is changed, check with your CITROËN dealer If the type of wheel is changed, wheel is changed,
that the wheel bolts are compatible with the new wheels.
Page 123 of 191
1 2 2
V
C H A N G I N G A W H E E L
Removal1. P a r k t h e v e h i c l e o n s t a b l e , fi r m g r o u n d t h a t i s n o t s l i p p e r y . A p p l y t h e parking brake. S w i t c h o f f t h e i g n i t i o n a n d e n g a g e fi r s t g e a r o r r e v e r s e g e a r , d e p e n d i n g on any slope.2. Position the jack at one of the four jacking-points provided on the sub-frame close to the wheels. Using the handle, unwind the jack until it reaches the ground.3. To unclip the wheel embellisher, pull using the end of the wheelbrace as a lever in one of the apertures.For vehicles with aluminium wheel rims:With a central embellisher, remove the embellisher, using the tool, to access the bolts.With visible wheel bolts, remove the chromed bolt protectors, usi ng the tool, before slackening the bolts.4. Continue to extend the jack until the wheel is a few centimetres off the ground.5. Undo the other bolts, remove the wheel.
-
-
R e fi t t i n g1. Fit the wheel on the hub, using the centring guide.2. Screw in the bolts but do not fully tighten them, remove the wheel centring guide in order to screw in the last bolt.3. Lower the jack and remove it.4. Tighten the wheel bolts, using the wheelbrace.5. R e fi t t h e e m b e l l i s h e r , t a k i n g c a r e t o a c c o m m o d a t e t h e t y r e v a l v e . T h e n p r e s s i n g a l l r o u n d i t s c i r c u m f e r e n c e .6. H a v e t h e o r i g i n a l w h e e l r e p a i r e d a n d r e fi t t e d a s s o o n a s p o s s i b l e .7. M a k e s u r e t h a t t h e t y r e i s a t t h e c o r r e c t p r e s s u r e ( s e e " V e h i c l e I d e n t i fi c a t i o n " a n d " U s e r P r e c a u t i o n s " ) a n d h a v e the wheel balancing checked.
Dimension of the spare wheel
I f y o u r s p a r e w h e e l h a s d i m e n s i o n s d i f f e r e n t f r o m t h o s e o f t h e n o r m a l v e h i c l e w h e e l s ( i d e n t i fi e d b y a l a b e l ) , i t i s i m p e r a t i v e t o u s e t h e s p a r e w h e e l o n l y t e m p o r a r i l y , t o d r i v e w i t h c a u t i o n , n o t t o e x c e e d 8 0 k m / h ( 5 0 m p h ) a n d t o h a v e t h e t y r e r e p a i r e d a n d t h e n o r m a l w h e e l r e fi t t e d a s s o o n a s p o s s i b l e .
Page 124 of 191
1 2 3
V
Because the aerosol is pressurised, do not expose it to temperatures higher than 50°C.
After provisionally repairing a tyre using the repair aerosol, you are advised not to drive at over 80km/h.
If your vehicle has no spare wheel, a repair aerosol is to be found in the boot.
Using the repair aerosol
See also the user instructions on the aerosol.Remove, if possible, the object which has caused the punc-ture.
Orient the wheel so that the valve is at ten o’clock or two o’clock.Shake the aerosol vigorously (in cold weather warm it in your hands for a few minutes).
With one hand hold the valve connector clear of the rim hole, with the other hand press the e n d o f t h e a e r o s o l n o z z l e fi r m l y onto the connector, keeping it in the line of the valve.Firmly maintain the pressure for one minute.
Rapidly remove the aerosol and immediately drive for around six miles.
R e i n fl a t e t h e t y r e a n d c h e c k i t s condition after some ten hours.
After using the repair aerosol, you should have the condition o f t h e t y r e , a s w e l l a s i t s i n fl a t i o n pressure, inspected.
P U N C T U R E
Advice - Recommendations
A punctured tyre should always be removed from the rim and thoroughly examined for dam-age before attempting any repair. When a repair is possible, it should be carried out as soon as possible to prevent further damage to the tyre.
Tyre repair should be carried out by a tyre specialist who will assume responsibility for the repair.Note:The towing eye is stowed either in the repair aerosol box or in the tool kit.
If there are two repair aerosols, this means that you need to use both of them for the temporary repair of the tyre.
Page 125 of 191
1 2 4
V
T O W I N G – L I F T I N G
Towing with wheels on the ground
T o w i n g e y e fi x i n g s a r e l o c a t e d a t t h e f r o n t a n d a t t h e r e a r o f t h e v e h i c l e .
To access them:Carefully lift the access cover.
Release it by pressing on the lower part.
A lug keeps the cover attached to the bumper, so that it do es not become lost.
The ignition key must be in position M to retain steering.
Use a bar with attachments to the towing eyes as above.
Movable towing eye
The towing ring is detachable and c a n b e fi t t e d e i t h e r a t t h e f r o n t o r a t the rear of the vehicle. It is stowed in the toolkit which is to be found either under one of the front seats or in the repair aerosol kit located in the boot.
When the engine is not running, the steering and the bra king are no longer assisted.
If you are towing another vehicle, the latter must be free-wheeling (gearbox in neutral).
ADVICE
Towing at low speed over a very short distance is authorised in exceptional cases depending on the regulations in force.
Otherwise, it is necessary to have your vehicle transported on a recovery truck.
TOWING REQUIREMENTS
Place the selector on position N (neutral).
Page 137 of 191
5
NOTES ON RADIO RECEPTIONYour radio will be subject to certain phenom-ena that are not encountered by domestic systems.The reception of AM and FM signals may suf fer from inter ference, which is caused by the nature and propagation of the signals a n d d o e s n o t r e fl e c t o n t h e q u a l i t y o f y o u r radio installation.In AM, the reception may be affected when passing under power lines or bridges, or when travelling through tunnels.In FM mode, the reception may be affected by the distance from the station transmit- t e r , t h e r e fl e c t i n g o f s i g n a l s o f f o b s t a c l e s (mountains, hills, tower blocks) and radio blackspots (no coverage from the station transmitter).
S ELECTION OF RADIO SOURCEPress button D to select the source.You can also do this by means of control 5at the steering wheel.
S E L EC T I O N O F FR EQ U E N C I E S A N D MEMORY BANKSPress button E successively to go through the memor y banks FM1, FM 2 and FM 3, fo r t he FM waveband, and t he m em o r y banks MW/LW, for the AM waveband.
R A D I O S O U R C E
M ANUAL SEARCHManual seearch is via buttons J or M.By keeping button J or M pressed, you will be able to scroll through the waveband. Scrolling will stop as soon as you release the button. The radio will remain tuned to the frequency that is displayed.
T UNING SENSITIVITYAutomat ic searc hes c an be c ar r ied out according to two levels of sensitivity :To capture the most power ful transmit-ters, choose the local search mode “LO” (default option).To capture the weakest or most distant transmitters, choose the sensitive search mode “DX”. S e a r c h f o r a s t a t i o n i s d o n e fi r s t i n “LO” (loc al) sensitivit y, then in “DX” (dist ant) sensitivity.To commence a search in sensitivity “DX” (distant) immediately , press twice in succes-sion on one of the buttons K or N.
Page 141 of 191
9
SELECTING CD SOURCEAfter inserting a CD, with the printed side facing upwards, the player will start playing the CD automatically.To c h a n g e m a n u a l l y t o C D s o u r c e (CD already inserted), press button D until you obtain the source you require.You can also do this by means of control 5at the steering wheel.
EJECTING A CDPress button B to eject the CD, the audio system will automatically switch to radio source.I f t h e C D i s n o t r e m o v e d w i t h i n 10 t o 15 seconds of being ejected, it will auto -matically be taken back into the CD player, although it will not be played.
S ELECTING A TRACKPress button K once to play the next track.Press button N once to return to the beginning of the track currently being played, press a second time to go back to the start of the previous track.Press the buttons successively to skip several tracks at a time.This can also be done via the control G. As the list of tracks is displayed on the screen, select the desired track using buttons J or M, then validate using button L.You can also do this via the controls 2 and 3at the steering wheel.
C D S O U R C E
F AST FORWARD AND RAPID REVERSE WITH ACCELERATED SOUNDTo move swiftly through the CD, press and keep pressed button K or KN, respectively for fast for ward or rapid reverse with acceler-ated sound.Play resumes as normal when the button is released.
M ENUThis menu allows activation/deactivation of two options : P l a y b a c k o f t h e fi r s t 7 s e c o n d s ( a p p r o x . ) of each track of the CD.Random playback of the CD tracks.This can be accessed in two ways :Either by pressing button O and proceed-ing as for Search of Stations RDS – for screen C, the sub-menu corresponds to the Audio Preferences.Or, provided you are in CD source, by pressing onbutton L. You can then access the Audio menu (for screen C only).
Note :If one of these options is active, it remains active for CD changer source.
Page 142 of 191
10C D C H A N G E R S O U R C E
SELECTING CD CHANGER SOURCEP r e s s o n b u t t o n D u n t i l y o u r e a c h C D changer.After the magazine engages, playback of the fi r s t t r a c k o f t h e fi r s t C D w i l l b e g i n .You can also do this by means of control 5at the steering wheel.
S ELECTING A CDTo select a CD, either press one of the pre-selection buttons 1 to 5 on the keypad P, or scroll using buttons J or M.The CD will start to play automatically.You can also do this by means of control 1at the steering wheel.After each change of source, on return to CD changer source, playback will resume at the same point where it had been inter-rupted.
S ELECTING A TRACKPress button K once to play the next track.Press button N once to return to the beginning of the track currently being played, press a second time to go back to the start of the previous track.Press the buttons successively to skip sev-eral tracks at a time.You can also do this by means of the controls 2 and 3 at the steering wheel.
F AST FORWARD AND RAPID REVERSE WITH ACCELERATED SOUNDPress and keep pressed one of the but-tons K or N respectively for fast for ward or rapid reverse with accelerated sound. Play resumes as normal when the button is released.
M ENUThis menu is for activation/deactivation of three options : P l a y b a c k o f t h e fi r s t 7 s e c o n d s ( a p p r o x . ) of each track of the CD.Repetition of the current CD.Random playback of tracks, CD by CD.This can be accessed in two ways :Either by pressing button O and proceed-ing as for Search of Stations RDS – for screen C, the sub-menu corresponds to the Audio Preferences.Or if you are in CD changer source by pressing button L. You then have access to the AUDIO menu (for screen C only).
Note :If one of these options is active, it remains active for CD source.
Page 163 of 191
NAV
17N A V I G A T I O N – T R A F F I C I N F O R M A T I O N
When navigation is to be used for the fi r s t t i m e , o r w h e n t h e b a t t e r y h a s b e e n disconnected for any reason, the naviga-tion system has to be initialised. For this operation the vehicle must be parked outdoors so that it can pick up satellite signals. Turn the ignition to position M (see vehicle Handbook) and leave for at l e a s t fi f t e e n m i n u t e s .
INTRODUCTIONThe on-board navigation system uses audible and visual instructions to guide you towards the destination of your choice.The system uses a cartographic database stored on a CD-ROM, and a GPS system.The G PS system enables your position to be plotted via contact with a number of satellites.The navigation system is composed of the following elements :A CD-ROM reader.A button for recall of the last voice mes-sage - during navigation, a long press on the end of the lighting control stalk 7repeats the latest voice information.Cartographic data in the form of a CDROM that has to be inserted, printed side up, in the aperture X.A synthesised voice for enunciating the guidance instructions during navigation.A display screen.A GPS aerial.Control on the dashboard and controls at the steering wheel.