2007 CHRYSLER SEBRING SEDAN instrument panel

ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC) – IF EQUIPPED
The Electronic Vehicle Information Center (EVIC) fea-
tures a driver-interactive display. It is located in the lower
left part of the cluster below the fuel and engine tem-
perature gauge. The EVIC consists of the following:
•System Status
•Vehicle information warning message displays
•Personal Settings (customer programmable features)
•Compass heading (N, S, E, W, NE, NW, SE, SW)
•Outside temperature display (°F or °C)
•Trip computer functions
•UConnect™ hands-free communication system dis-
plays (if equipped)
•Audio mode display – 12 preset Radio Stations or CD
Title and Track number when playing
•Tire Pressure Monitor System (TPMS) (if equipped)
•Navigation system screens (if equipped)
Electronic Vehicle Information Center (EVIC)
Displays
When the appropriate conditions exist, the Electronic
Vehicle Information Center (EVIC) displays the following
messages.
•Turn Signal On (with a continuous warning chime)
•Left Front Turn Signal Light Out (with a single chime)
•Left Rear Turn Signal Light Out (with a single chime)
EVIC Display Location
UNDERSTANDING YOUR INSTRUMENT PANEL 147
4

•Right Front Turn Signal Light Out (with a single
chime)
•Right Rear Turn Signal Light Out (with a single chime)
•RKE (Remote Keyless Entry) Battery Low (with a
single chime)
•Memory #1/#2 Profile Set
•Memory #1/#2 Profile Recall
•Memory System Disabled – Vehicle Not In Park (with
a single chime)
•Memory System Disabled – Seat Belt Buckled (with a
single chime)
•Personal Settings Not Available – Vehicle Not in Park.
•Left/Right Front Door Ajar (one or more, with a single
chime if speed is above 1 mph)
•Left/Right Rear Door Ajar (one or more, with a single
chime if speed is above 1 mph)
•Door(s) Ajar (with a single chime if vehicle is in
motion)
•Trunk Ajar (with a single chime)
•Low Washer Fluid (with a single chime)
•Headlights On
•Key In Ignition
EVIC Functions
The 2nd (MENU / STEP) and 3rd (RESET) buttons of the
center instrument panel switch bank are used for EVIC
Functions.
148 UNDERSTANDING YOUR INSTRUMENT PANEL

Trip Functions
MENU / STEP Button
Press and release the MENU / STEP button
(located near the radio) until one of the follow-
ing Trip Functions displays in the EVIC:
•Average Fuel Economy
•Distance To Empty
•Elapsed Time
•Display Units of Measure in
Press the STEP button to cycle through all the Trip
Computer functions.
The Trip Functions mode displays the following information:
•Average Fuel Economy
Shows the average fuel economy since the last reset.
When the fuel economy is reset, the display will read,
“RESET” or show dashes for two seconds. Then, the
history information will be erased, and the averaging will
continue from the last fuel average reading before the
reset.
•Distance To Empty (DTE)
Shows the estimated distance that can be traveled with
the fuel remaining in the tank. This estimated distance is
determined by a weighted average of the instantaneous
and average fuel economy, according to the current fuel
tank level. DTE cannot be reset through the RESET
button.
UNDERSTANDING YOUR INSTRUMENT PANEL 149
4

NOTE:Significant changes in driving style or vehicle
loading will greatly affect the actual drivable distance of
the vehicle, regardless of the DTE displayed value.
•When the DTE value is less than 30 miles (48 km)
estimated driving distance, the DTE display will
change to a text display ofLOW FUEL.This display
will continue until the vehicle runs out of fuel. Adding
a significant amount of fuel to the vehicle will turn off
theLOW FUELtext and a new DTE value will
display.
•Elapsed Time
Shows the total elapsed time of travel since the last reset
when the ignition switch is in the ACC position. Elapsed
time will increment when the ignition switch is in the ON
or START position.
•Display Units of Measure in:
To make your selection, press and release the RESET
button until “US” or “METRIC” appears.
To Reset The Display
Pressing and holding the RESET button once
will clear the function currently being dis-
played. Reset will only occur if a resettable
function is currently being displayed. To reset
all resettable functions, press and release the
RESET button a second time within 3 seconds
of resetting the currently displayed function (Reset ALL
will be displayed during this 3-second window).
Compass Display
COMPASS Button
The compass readings indicate the direction
the vehicle is facing. Press and release the
compass button to display one of eight com-
pass readings and the outside temperature. The
RESET button is used in conjunction with the MENU /
STEP buttons to navigate and select Menu Preferences.
Automatic Compass Calibration
This compass is self-calibrating, eliminating the need to
calibrate the compass manually. When the vehicle is new,
the compass may appear erratic and the EVIC will
display “FLASH THE CAL” indicator until the compass
RESET
Button
150 UNDERSTANDING YOUR INSTRUMENT PANEL

is calibrated. Calibrate the compass by completing one or
more 360° turns (in an area free from large metal or
metallic objects) until the “FLASH THE CAL” message
displayed in the EVIC turns off. The compass will now
function normally.
Manual Compass Calibration
If the compass appears erratic, inaccurate, or abnormal,
you may wish to calibrate the compass manually. Prior to
calibrating the compass, make sure the proper zone is
selected. Continue to calibrate the compass manually
using the following steps:
1. Start the engine and leave the transmission selector in
PARK, in order to enter the EVIC Programming Menus.
2. Press the Step Button Several Times until “Personal
Settings” is displayed in the EVIC window.
3. Once in “Personal Settings,” Press the STEP button
until “Calibrate Compass Yes” displays in the EVIC
window. Press and release the RESET Button and the
“CAL” indicator will come on solid.4. Drive the vehicle slowly, completing one or more
circles (in an area free from large metal or metallic
objects) until the “CAL” message turns off. The compass
will now function normally.
Compass Variance
Compass Variance is the difference between magnetic
North and Geographic North. In some areas of the
country, the difference between magnetic and geographic
North is great enough to cause the compass to give false
readings. If this occurs, the compass variance must be set
using the following procedure:
NOTE:Magnetic materials and cell phones should be
kept away from the top of the Instrument Panel. This is
where the compass sensor is located.
UNDERSTANDING YOUR INSTRUMENT PANEL 151
4

Procedure to Update the Variance:
1. Turn the ignition switch to the ON position while
leaving the transmission selector in PARK.
2. Press the Step Button Several Times until “Personal
Settings” is displayed in the EVIC window.
3. Once in “Personal Settings,” Press the STEP button
until “Compass Variance” and the current value displays
in the EVIC window.
4. Press and release the RESET Button to increment the
Variance Value by one, (one button press per update),
until the proper variance zone is selected according to the
map.
NOTE:The Variance values will wrap around from 15
back to 1. The Default Variance is Zone 8.
5. Press and release the RESET button to exit. Press the
STEP button if you wish to calibrate the compass manu-
ally (see: “Manual Compass Calibration” listed above).
152 UNDERSTANDING YOUR INSTRUMENT PANEL

Telephone — If Equipped
Press and release the MENU button until “Telephone”
displays in the EVIC.
When the appropriate conditions exist, the EVIC pro-
vides the following telephone information:
•Phone status: idle; voice mail; roaming; battery
strength; and signal strength in increments of 20
percent.
•Call status: Incoming call; connecting; connected; air
time in minutes and seconds; call ended; call failed;
roaming; and no phone connection.
•UConnect Active.
•Caller ID phone number display.
When the appropriate conditions exist, and if supported
by the cell phone, the EVIC will display the following
telephone symbols:The EVIC displays this symbol to indicate the
signal strength of the UConnect™ phone. The
number of horizontal bars increases as the
strength of the UConnect™ phone signal in-
creases.
The EVIC displays this symbol to indicate an
incoming call.
The EVIC displays this symbol to indicate that
the UConnect™ phone is currently in analog
mode.
The EVIC displays this symbol to indicate that
the UConnect™ phone is currently roaming.
Signal
Strength
Incom-
ing Call
Analog
Roam-
ing
UNDERSTANDING YOUR INSTRUMENT PANEL 153
4

The EVIC displays this symbol to indicate that
you have voice mail.
The EVIC displays this symbol to indicate a
text message.
The EVIC displays this symbol to indicate the
battery strength of the UConnect™ phone.
The EVIC displays this symbol to indicate that
a phone connection has been made.The EVIC displays this symbol to indicate that
the UConnect™ phone is currently not avail-
able.
Navigation — If Equipped
Navigation Display Control
Press and release the MENU button until Navigation
displays in the EVIC. When the Navigation System is On,
the buttons can be used to select the Map or Menu
display on the Navigation Unit. When the Menu display
is active, the STEP button can be used to scroll through
the list, the RESET button can be used to select an item,
and the AUDIO MODE button can be used to return to
the previous menu. When the Map display is active,
pressing the RESET button will change the Navigation
Unit Display to the Menu.
Voice
Mail
Text
Message
Battery
Strength
Call in
Progress
Phone
Not
Avail-
able
154 UNDERSTANDING YOUR INSTRUMENT PANEL