2007 CHEVROLET UPLANDER seats

Head Restraints
Adjust the head restraint so that the top of the
restraint is at the same height as the top of
the occupant’s head. This position reduces the
chance of a neck injury in a crash.
The height of the head restraints can be adjusted
on the rst and second row seats. Pull the
head restraint up or push it down to adjust it.
The head restraints on the third row seat cannot
be adjusted.
Rear Seats
Rear Seat Operation
The rear seats in your vehicle have levers and
straps used to adjust, remove, and reinstall
the seats. By using the levers and straps in the
correct order, you can easily remove the seats
from the vehicle. If your vehicle has second row
captain chairs with airbags, the seats cannot
be removed.
When reinstalling the seats, make sure the seats
are in the proper positions.
If your vehicle has a second row center console, it
can be removed. SeeSecond Row Center
Console on page 183. Do not put a seat in the
center position because the safety belt cannot be
worn properly in this position. SeeSafety Belts:
They Are for Everyone on page 32.
Bucket Seats
Your vehicle may have bucket seats in the second
row. These seats can be adjusted several
different ways.
13

Fold and Tumble Feature
{CAUTION:
Using the third row seating position while
the second row is folded, or folded and
tumbled, could cause injury in a sudden
stop or crash. Be sure to return the seat
to the passenger seating position. Push
and pull on the seat to make sure it is
locked into place.
The second row bucket seats can be folded and
tumbled forward. Use this feature for exiting
and entering third row seats, if the vehicle
has them.
1. Make sure the adjustable head restraints are
in the fully lowered position.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.2. Fold the seatback
at on the seat.
You can do this by either pulling on the nylon
strap, located on the rear right hand side
of the seat, or by lifting the recline lever,
located on the front right hand side of the
seatback.
3. Slide the seat all the way back in this position.
14

4. Release the rear set
of seat hooks from
the oor pins by
pulling the
nylon strap, located
at the base of
the seat. Use the
strap to guide
the seat forward.
To return the seat to the original position, do the
following:
1. Align the seat so that the rear hooks on the
seat are over the rear oor pins. Push down
rmly on the rear of the seat so that the
rear hooks attach to the rear oor pins.
2. Try to raise the seat to check that it is locked
to the oor.3. Pull the nylon strap, located on the rear right
hand side of the seat, or lift the recline lever,
located on the front right hand side of the
seatback, to raise the seatback to the upright
position.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
4. Push and pull on the seatback to check that it
is locked.
One of the bucket seats may be equipped with a
built-in child restraint. SeeBuilt-In Child
Restraint on page 85.
15

Adjusting the Bucket Seats Forward
and Rearward
There are two adjustment levers on the second
row bucket seats that enable them to move
forward or rearward.
One is located below the front of the seat.The other lever is
located on the rear of
the seat.
To adjust the second row bucket seats forward or
rearward, do the following:
1. Lift up either lever and slide the seat forward
or rearward.
2. Release the lever when the seat is in the
desired position.
3. Push and pull on the seat to make sure it is
locked.
16

To recline the seatback, do the following:
1. Pull the nylon strap or lift the recline lever.
2. Press back on the seatback until it is in
the desired position
3. Let go of the strap or lever.
Removing the Bucket Seats
To remove the bucket seats, do the following:
1. Make sure the head restraint is in the
fully lowered position.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
2. Fold the seatback at on the seat, by either
pulling on the nylon strap, located on the rear
right hand side of the seat, or by lifting the
recline lever, located on the front right
hand side of the seatback.3. Lift either one of the adjuster levers and slide
the seat to the most rearward position. See
“Adjusting the Bucket Seats Forward and
Rearward” earlier in this section.
4. Release the rear set of hooks from the oor
pins by pulling the nylon strap, located at the
base of the seat. Use the strap to guide
the seat forward.
18

5. To release the front seat hooks from the oor
pins, squeeze the angled bar, located beneath
the seat toward the straight crossbar.
6. Remove the seat by rocking it slightly forward,
then toward the rear of the vehicle while
pulling it out. This should be done in
one motion.
Reinstalling the Bucket Seats
{CAUTION:
A safety belt that is improperly routed, not
properly attached, or twisted will not
provide the protection needed in a crash.
The person wearing the belt could be
seriously injured. After installing the seat,
always check to be sure that the safety
belts are properly routed and attached,
and are not twisted.
Do not install the seat facing the rear of the
vehicle, as it will not lock into place. If more
storage room is needed behind the seat, slide the
seat forward.
Make sure the seat is in the full rear position
before beginning this procedure.
19

To reinstall the bucket seats, do the following:
1. With the seat folded, squeeze the angled bar
beneath the seat toward the straight crossbar,
while placing the front hooks of the seat
into the front two oor pins.
2. Make sure the seat
is angled so that the
front seat hooks
clear the oor pins.
If the front hooks
are not attached
correctly, the seat’s
rear hooks will
not attach to the rear
set of oor pins.
If the front hooks are not attaching correctly,
check that the seat is in the full rear position.3. Firmly push the rear seat hooks into the rear
oor pins by pushing down the rear of
the seat.
20

Removing a Captain Chair (without a
Side Impact Airbag)
If your vehicle has captain chairs with side impact
airbags, the seats cannot be removed. See
Where Are the Airbags? on page 99for more
information.
To remove a captain chair, do the following:
1. Pull the nylon strap behind the seat to release
the rear hooks from the oor pins.2. The seat can then be lifted off the front oor
pins and removed from the vehicle.
24