2007 CHEVROLET UPLANDER lock

3. Tilt the retainer at the end of the cable to
remove the compact spare tire, so it can
be pulled up through the wheel opening.
The hoist is used to store a full-size or a at
road tire under the vehicle. SeeStoring a
Flat or Spare Tire and Tools on page 513for
more information.
4. Remove the compact spare tire from the cable.If the compact spare tire will not lower, check
under the vehicle to see if the tire is hanging loose
and the cable end and spring under the wheel
plate are missing. If so, the secondary latch
system is engaged. SeeSecondary Latch System
on page 511.
To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 504.
Removing the Flat Tire and
Installing the Spare Tire
Your vehicle may have aluminum wheels. If so, you
will see exposed stainless steel wheel nuts. Use the
wheel wrench to loosen all of the wheel nuts. Do not
remove them yet. Or, your vehicle may have steel
wheel covers. To remove the wheel covers and
wheel nut caps, loosen the plastic nut caps with the
wheel wrench in a counterclockwise direction. If
needed, you can nish loosening with your ngers.
504

The plastic nut caps will not come off. Use the at
end of the wheel wrench and pry along the edge of
the cover until it comes off. The edge of the wheel
cover could be sharp, so do not try to remove it with
your bare hands. Do not drop the cover or lay it face
down, as it could become scratched or damaged.
Once you have removed the wheel cover, use the
following procedure to remove the at tire and
install the spare tire.1. Loosen the wheel
nuts using the
folding wrench,
but do not
remove them.
Turn the handle counterclockwise about
180 degrees, then ip the handle back to the
starting position. This avoids taking the
wrench off the lug nut for each turn.
Notice:If your vehicle has wheel locks and
you use an impact wrench to remove the wheel
nuts, you could damage the lock nut or
wheel lock key. Do not use an impact wrench
to remove the wheel nuts if your vehicle
has wheel locks.
505

{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when it is
supported only by a jack.
{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall. To
help avoid personal injury and vehicle
damage, be sure to t the jack lift head
into the proper location before raising the
vehicle.4. Attach the folding wrench (A) to the jack (B),
and turn the wrench clockwise to raise the
jack head approximately 3 inches (7.6 cm).
507

5. Raise the vehicle by turning the folding
wrench clockwise in the jack. Raise the
vehicle far enough off the ground so there is
enough room for the compact spare tire
to t under the wheel well.
6. Remove all the wheel nuts and take off the
at tire.
{CAUTION:
Rust or dirt on the wheel, or on the parts
to which it is fastened, can make the
wheel nuts become loose after a time. The
wheel could come off and cause an
accident. When you change a wheel,
remove any rust or dirt from the places
where the wheel attaches to the vehicle. In
an emergency, you can use a cloth or a
paper towel to do this; but be sure to use
a scraper or wire brush later, if needed, to
get all the rust or dirt off.
508

9. Lower the vehicle by attaching the folding
wheel wrench to the jack and turning the
wrench counterclockwise. Lower the
jack completely.
{CAUTION:
Incorrect wheel nuts or improperly
tightened wheel nuts can cause the wheel
to come loose and even come off. This
could lead to an accident. Be sure to use
the correct wheel nuts. If you have to
replace them, be sure to get new GM
original equipment wheel nuts. Stop
somewhere as soon as you can and have
the nuts tightened with a torque wrench to
the proper torque specication. See
Capacities and Specifications on page 533
for wheel nut torque specication.
Notice:Improperly tightened wheel nuts can
lead to brake pulsation and rotor damage.
To avoid expensive brake repairs, evenly
tighten the wheel nuts in the proper sequence
and to the proper torque specication. See
Capacities and Specifications on page 533for
the wheel nut torque specication.
510

{CAUTION:
Someone standing too close during the
procedure could be injured by the jack. If
the spare tire does not slide off the jack
completely, make sure no one is behind
you or on either side of you as you pull
the jack out from the spare.To release the spare tire from the secondary latch,
do the following:
1. Place the jack under the vehicle, ahead of the
rear bumper. Position the center lift point of the
jack under the center of the compact spare tire.
2. Turn the folding wrench clockwise to raise the
jack until it lifts the secondary latch device
under the wheel plate.
3. Keep raising the jack until the compact spare
tire stops moving upward and is held rmly in
place. This lets you know that the secondary
latch has released.
512

4. Lower the jack by turning the folding wrench
counterclockwise. Keep lowering the jack until
the compact spare tire is resting on the
folding wrench.
5. Grasp the compact spare tire with both hands
and pull it out from under the vehicle.
6. Reach under the vehicle and remove the
folding wrench and jack.
Have the hoist assembly inspected as soon as
you can. You will not be able to store a spare or
at tire using the hoist assembly until it has
been repaired or replaced.Storing a Flat or Spare Tire
and Tools
{CAUTION:
Storing a jack, a tire, or other equipment
in the passenger compartment of the
vehicle could cause injury. In a sudden
stop or collision, loose equipment could
strike someone. Store all these in the
proper place.
513

Your vehicle has an airbag system. Before
attempting to add anything electrical to your
vehicle, seeServicing Your Airbag-Equipped
Vehicle on page 112.
Headlamp Wiring
The headlamp wiring is protected by four internal
fuses in the underhood fuse block. An electrical
overload will cause the lamps to go on and off, or
in some cases to remain off. If this happens,
have your headlamp wiring checked right away.
Windshield Wiper Fuses
The windshield wiper motor is protected by an
internal fuse in the underhood fuse block. If
the motor overheats due to heavy snow, etc., the
wiper will stop until the motor cools. If the
overload is caused by some electrical problem, be
sure to get it xed.
The rear washer pump is controlled by a relay
located in the engine compartment, behind
the windshield washer uid reservoir. The rear
wiper motor is protected by a fuse located in the
instrument panel fuse block.
Power Windows and Other Power
Options
Circuit breakers in the instrument panel fuse panel
protect the power windows and other power
accessories. When the current load is too heavy,
the circuit breaker opens and closes, protecting
the circuit until the problem is xed.
Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected
from short circuits by a combination of fuses,
circuit breakers, and fusible thermal links.
Look at the silver-colored band inside the fuse. If
the band is broken or melted, replace the fuse.
Be sure you replace a bad fuse with a new one of
the identical size and rating.
If you ever have a problem on the road and do not
have a spare fuse, you can borrow one that has
the same amperage or use one of the spare fuses
in the underhood fuse block. Just pick some
feature of your vehicle that you can get along
without, like the radio or cigarette lighter, and use
its fuse if it is the right amperage. Replace it
as soon as you can.
527