2007 CADILLAC XLR V seat memory

Front Seats..................................................... 8
Power Seats................................................. 8
Power Lumbar.............................................. 9
Heated and Cooled Seats............................. 9
Memory Seat, Mirrors and
Steering Wheel........................................ 10
Power Reclining Seatbacks......................... 11
Safety Belts.................................................. 13
Safety Belts: They Are for Everyone........... 13
Questions and Answers About
Safety Belts............................................. 17
How to Wear Safety Belts Properly............. 18
Driver Position............................................. 18
Safety Belt Use During Pregnancy.............. 26
Passenger Position...................................... 27
Safety Belt Pretensioners............................ 27
Safety Belt Extender................................... 27
Child Restraints............................................ 28
Older Children............................................. 28
Infants and Young Children......................... 31
Child Restraint Systems.............................. 35Lower Anchors and Tethers for
Children (LATCH).................................... 39
Securing a Child Restraint in the
Passenger Seat Position.......................... 40
Airbag System.............................................. 44
Where Are the Airbags?.............................. 47
When Should an Airbag Inate?.................. 49
What Makes an Airbag Inate?................... 51
How Does an Airbag Restrain?................... 51
What Will You See After an Airbag
Inates?................................................... 52
Passenger Sensing System......................... 53
Servicing Your Airbag-Equipped Vehicle...... 58
Adding Equipment to Your
Airbag-Equipped Vehicle.......................... 59
Restraint System Check............................... 60
Checking the Restraint Systems.................. 60
Replacing Restraint System Parts
After a Crash........................................... 61
Section 1 Seats and Restraint Systems
7

Memory Seat, Mirrors and Steering
Wheel
Your vehicle is equipped with the memory
package. The controls for these features are
located on the driver’s seat, and are used
to program and recall memory settings for the
driver’s seating positions.Use the following steps to program each button:
1. Adjust the driver’s seat including the seatback
recliner, lumbar, both outside mirrors and the
steering wheel to a comfortable position.
2. Press and hold button 1 until two beeps are
heard, then release the button.
A second mirror, seating and steering wheel
position can be programmed by repeating
the above steps and pressing button 2 (for
driver 2). Each time a memory button is pressed
and released, a single beep will sound. Each
time button 1 or 2 is pressed and released while
the vehicle is in PARK (P), the memory positions
will be recalled after a brief delay. If the vehicle
is not in PARK (P), three beeps will be heard and
the memory position will not be recalled.
When the engine is started, the seat, mirrors, and
steering wheel may automatically adjust to their
programmed positions.
To stop recall movement of the memory feature at
any time, press one of the power seat controls,
power mirror control buttons, memory buttons, or
power steering column control.
10

Two personalized exit positions can be set by rst
recalling the driving position (by pressing 1 or 2),
then positioning the steering wheel and seat in the
desired exit positions and then pressing and
holding the exit button until two beeps are heard.
The exit button is located between buttons 1 and 2.
With the vehicle in PARK (P), the exit position
for the previously set driver can be recalled
by pressing the exit button.
When you use the keyless access transmitter to
unlock your vehicle, automatic seat and steering
wheel movement to the exit position may
occur. The numbers on the back of the
transmitter, 1 and 2, corresponds to the numbers
on the memory buttons.
Further programming for automatic seat and mirror
movement can be done using the Driver
Information Center (DIC).
For programming information, seeDIC Vehicle
Personalization on page 220.Power Reclining Seatbacks
Your seats have power
reclining seatbacks.
Use the vertical power seat control located on the
outboard side of the seat to operate them.
To recline the seatback, press the control
toward the rear of the vehicle.
To raise the seatback, press the control
toward the front of the vehicle.
11

K(Unlock):Press this button once to unlock the
driver’s door. The indicator light on the door
will ash twice. Press the button twice within
10 seconds to unlock both doors. If it is dark
enough outside, your interior lamps will come on.
Your memory settings may also be recalled when
you press the unlock button on the keyless access
transmitter. SeeMemory Seat, Mirrors and Steering
Wheel on page 10for more information.
G(Trunk):Press and hold this button for
about one second to open the trunk while
the engine is turned off or the shift lever is in
PARK (P).
Matching Transmitter(s) to Your
Vehicle
Each keyless access transmitter is coded to
prevent another transmitter from working with your
vehicle. If a transmitter is lost or stolen, a
replacement can be purchased through your
dealer. Remember to bring any remaining
transmitters with you when you go to your dealer.
Once your dealer has coded the new transmitter,
the lost transmitter will not work with your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.
To match a new transmitter to your vehicle when
you have a recognized transmitter, do the
following:
1. The vehicle must be off.
2. Have the recognized and new, unrecognized
transmitters on your person.
3. Go to the rear of the vehicle and insert the
vehicle key into the key cylinder located on
the lower rear fascia on the driver’s side of the
vehicle. SeeTrunk on page 77for more
information on the key cylinder.
4. Open the trunk.
69

Outside Power Heated Mirrors
The controls for the
outside power mirrors
are located is on
the driver’s door
armrest.
Move the selector switch, located below the
four-way control pad, to the left or the right to
choose the driver’s side or passenger’s side mirror.
Use the arrows located on the four-way control
pad to adjust the position of the mirror. Adjust each
outside mirror so that a little of the vehicle and
the area behind it can be seen while sitting
in a comfortable driving position. Keep the selector
switch in the center position when not adjusting
either outside mirror.Both mirrors have a heated feature to rid them of
snow, ice, or condensation. They will heat
when the rear window defogger is turned on. See
“Rear Window Defogger” underDual Climate
Control System on page 178. If the vehicle has the
memory option, the preferred mirror position can
be stored. SeeMemory Seat, Mirrors and Steering
Wheel on page 10.
Both mirrors can be manually folded inward by
pulling them toward the vehicle. This feature may
be useful when going through a car wash or a
conned space. Push the mirrors away from the
vehicle, to the normal position, before driving.
Outside Automatic Dimming Mirror
The driver’s side mirror will adjust for the glare of
headlamps behind you. This feature is controlled by
the on and off settings on the inside automatic
dimming rearview mirror. SeeAutomatic Dimming
Rearview Mirror with OnStar
®on page 104.
105

Power Tilt Wheel and Telescopic
Steering Column
The power tilt wheel
control is located on the
outboard side of the
steering column.
To operate the power tilt feature, push the control
up and the steering wheel will tilt up. Push the
control down and the steering wheel will go down.
Push the control forward and the steering wheel
moves toward the front of the vehicle. Push
the control rearward and the steering wheel moves
toward the rear of the vehicle. To set the memory
position, seeDIC Vehicle Personalization on
page 220andMemory Seat, Mirrors and Steering
Wheel on page 10.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. See
Turn and Lane-Change Signals on page 142.
3Headlamp High/Low-Beam Changer. See
Headlamp High/Low-Beam Changer on
page 143.
-Fog Lamps. SeeFog Lamps on page 168.
141

DIC Vehicle Personalization
Your vehicle has personalization capabilities that
allow you to program certain features to a
preferred setting for up to two drivers. The back of
the keyless access transmitters are labelled 1 or 2.
The current driver’s preferences are recalled
when one of the following occurs:
The lock or unlock button on the keyless
access transmitter, programmed as 1 or 2, is
pressed.
The appropriate memory button, 1 or 2,
located on the driver’s seat is pressed.
SeeMemory Seat, Mirrors and Steering Wheel
on page 10for more information.
A valid keyless access transmitter is detected
upon opening the driver’s door.
If more than one valid keyless access transmitter
is detected upon opening the driver’s door, the
driver preferences for the lowest driver number will
be recalled.
If a keyless access transmitter is programmed
as #3 or #4, the personalization system will
not recognize the transmitter. The Driver
Information Center (DIC) will not display a currentdriver number and the features that are normally
programmed through the DIC will be set to
the default states. Also, if the OPTIONS button is
pressed, the DIC does not display the menus
used to set personalizations, but instead displays
OPTIONS UNAVAILABLE for a few seconds.
Feature Programming
To change feature preferences, make sure the
vehicle is running and in PARK (P). To avoid
excessive drain on the battery, it is recommended
that the headlamps are turned off. Press the
OPTIONS button and the Driver Information Center
(DIC) will display the current driver for a few
seconds, then display the rst personalization
menu item. You can now use the OPTIONS button
to change the setting of the displayed feature.
Press the top or bottom of the information button
to scroll up or down the list of features. When
you get to a feature you want to change, press the
OPTIONS button again. When you are nished,
press the RESET button to exit the personalization
menu. If no button is pressed within 45 seconds,
the DIC will exit the personalization menu.
The following are DIC options that will be available
in the personalization menu.
220

SEARCH:Touch this button to search to a certain
scene on the DVD. Depending on the type of
DVD you are using, this button may or may not be
available.
r(Rewind):Touch this button to rewind through
a scene during playback.
r(Resume):Touch this button to resume
playing a DVD.
c(Stop):Touch this button to stop the DVD.
j(Pause):Touch this button to pause the DVD.
[(Forward):Touch this button to advance
rapidly during playback.
L(Frame Advance):Touch this button to
advance by chapter during playback.
Radio Personalization with Home
and Away Feature
With this feature, you can recall the latest audio
system settings as adjusted the last time your
vehicle was operated. This feature allows
two different drivers to store and recall their own
audio system settings. The settings recalled by the
audio system are determined by which transmitter
(1 or 2) was used to enter the vehicle. The
number on the back of the transmitter corresponds
to driver 1 or to driver 2. The audio system
settings will automatically adjust to where they
were last set by the identied driver. The settings
can also be recalled by briey pressing the
MEMORY seat switches 1 or 2 located on the
driver’s door.
Your audio system can store HOME and AWAY
preset stations. HOME and AWAY preset stations
allow you to use one set of preset radio settings
in the area where you live, and another set
when you go out of town. That way, you will not
need to reprogram your preset stations every time
you travel.
311