2007 CADILLAC XLR driver seat adjustment

Power Lumbar
The driver’s and
passenger’s seatback
lumbar support switches
are located on the
outboard sides of
the seats.
Use the power seat controls rst to get the proper
position, then continue with the lumbar adjustment.
Use the top lumbar switch to adjust support to
the middle seatback and the bottom lumbar switch
to adjust support to the lower seatback. Press
the front of the switch to increase support and the
rear of the switch to decrease support.
Keep in mind that as your seating position
changes, as it may during long trips, so should the
position of your lumbar support. Adjust the seat
as needed.
Heated and Cooled Seats
The buttons for the heated and cooled seats are
located on the climate control system.
((Heated/Cooled Seat):Press this button to
turn the feature on. The button on the left controls
the driver’s seat and the button on the right
controls the passenger’s seat. Each press of the
button will take you to a different setting. The
settings available in order are HI HEAT, LO HEAT,
OFF, HI COOL, LO COOL and OFF. You will be
able to feel the temperature change in a few
minutes.
The feature will automatically turn off when the
vehicle is turned off. SeeDual Climate Control
System on page 178for more information.
9

Outside Curb View Assist Mirror
The passenger’s side mirror is also capable
of performing the curb view assist feature. This
feature will cause the mirror to tilt to a factory
programmed position when the vehicle is in
REVERSE (R). This feature may be useful in
allowing you to view the curb when you are parallel
parking.
If further adjustment is needed after the mirror is
tilted, the mirror switch may be used. The
mirror will then return to this new position when
the vehicle is shifted into REVERSE (R).
When the vehicle is shifted out of REVERSE (R)
and a ve-second delay has occurred, the
passenger’s side mirror will return to its original
position.
This feature can be enabled/disabled through the
Driver Information Center (DIC). See “Park
Assist” underDIC Vehicle Personalization on
page 220for more information.
Outside Convex Mirror
{CAUTION:
A convex mirror can make things (like
other vehicles) look farther away than
they really are. If you cut too sharply into
the right lane, you could hit a vehicle on
your right. Check your inside mirror or
glance over your shoulder before
changing lanes.
The passenger side mirror is convex. A convex
mirror’s surface is curved so more can be
seen from the driver’s seat. It also makes things
look farther away than they really are.
106

A/C OFF (Air Conditioning):Press this button to
turn off the air conditioning compressor. Press
AUTO to return to automatic operation. The
compressor cannot be turned off in either the
defrost or oor/defog mode.
((Heated/Cooled Seat):Press this button to
turn the feature on. The button on the left controls
the driver’s seat and the button on the right
controls the passenger’s seat. Each press of the
button will take you to a different setting. The
settings available in order are HI HEAT, LO HEAT,
OFF, HI COOL, LO COOL and OFF. You will be
able to feel the temperature change in a few
minutes.
The feature will automatically turn off when the
vehicle is turned off.
?(Recirculation):Press this button to turn the
recirculation mode on or off. The air conditioning
compressor also comes on. This mode keeps
outside air from coming in the vehicle. It can be
used to prevent outside air and odors from
entering your vehicle or to help cool the air inside
your vehicle more quickly.Recirculation is not available in defrost or
oor/defog modes.
Using recirculation for long periods of time may
cause the air inside your vehicle to become
too dry. To prevent this from happening, after the
air in your vehicle has cooled, turn the
recirculation mode off.
Sensors
There are sensors to measure the temperature
and sun’s effect on passenger comfort.
The solar sensor on your vehicle monitors the
solar radiation then uses the information to
maintain the selected temperature when operating
in AUTO mode by initiating needed adjustments
to the temperature, the fan speed and the air
delivery system. The system may also supply
cooler air to the side of the vehicle facing the sun.
The recirculation mode will also be activated,
as necessary. Do not cover the solar sensor
located on the top of the instrument panel near
the windshield or the system will not work properly.
181

The vehicle should be properly prepared as
follows:
The vehicle should be placed so the
headlamps are 25 ft (7.6 m) from a light
colored wall.
The vehicle must have all four tires on a
perfectly level surface which is level all
the way to the wall.
The vehicle should be placed so it is
perpendicular to the wall.
The vehicle should not have any snow, ice or
mud attached to it.
The vehicle should be fully assembled and all
other work stopped while headlamp aiming is
being done.
The vehicle should be normally loaded with a
full tank of fuel and one person or 160 lbs
(75 kg) on the driver’s seat.
Tires should be properly inated.
Start the vehicle and rock it to level the
suspension.Headlamp aiming is done with the low-beam
headlamps. The high-beam headlamps are
correctly aimed if the low-beam headlamps are
aimed properly.
The headlamp aiming
device is under the
hood near the
headlamps.
Adjustment screws can be turned with an
E8 Torx
®socket or T15 Torx screwdriver.
409