2007 CADILLAC STS lock

When replacing the fuel cap, turn it clockwise until
it clicks. Make sure the cap is fully installed.
The diagnostic system can determine if the fuel
cap has been left off or improperly installed.
This would allow fuel to evaporate into the
atmosphere. SeeMalfunction Indicator Lamp on
page 252.
The CHECK GAS CAP message will appear on
the Driver Information Center (DIC) display if
the fuel cap is not reinstalled properly. SeeDIC
Warnings and Messages on page 264for
more information.
{CAUTION:
If a re starts while you are refueling, do
not remove the nozzle. Shut off the ow of
fuel by shutting off the pump or by
notifying the station attendant. Leave the
area immediately.
Notice:If you need a new fuel cap, be sure to
get the right type. Your dealer can get one
for you. If you get the wrong type, it may not
t properly. This may cause your malfunction
indicator lamp to light and may damage
your fuel tank and emissions system. See
Malfunction Indicator Lamp on page 252.
370

After you have removed the sight shields (if equipped) on the 3.6L V6 engine, here is what you will see:
A. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 488.
B. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 404.
C. Battery. SeeBattery on page 408.
D. Passenger Compartment Air Filter. See
Passenger Compartment Air Filter on page 239.
E. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 403.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 380.G. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 380.
H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 405.
I. Engine Coolant Surge Tank and Pressure Cap.
SeeCoolant Surge Tank Pressure Cap on
page 393andCooling System on page 396.
J. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 386.
375

After you have removed the sight shields (if equipped) on the 4.6L V8 engine, here is what you will see:
A. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 488.
B. Battery. SeeBattery on page 408.
C. Passenger Compartment Air Filter. See
Passenger Compartment Air Filter on page 239.
D. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 404.
E. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 403.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 380.G. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 380.
H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 405.
I. Engine Coolant Surge Tank and Pressure Cap.
SeeCoolant Surge Tank Pressure Cap on
page 393andCooling System on page 396.
J. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 386.
377

After you have removed the sight shields (if equipped) on the 4.4L V8 STS-V engine, here is what
you will see:
A. Battery. SeeBattery on page 408.
B. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 488.
C. Passenger Compartment Air Filter. See
Passenger Compartment Air Filter on page 239.
D. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 404.
E. Intercooler System Pressure Cap. SeeEngine
Coolant on page 389.
F. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 403.
G. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 380.
H. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 380.I. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 405.
J. Engine Coolant Surge Tank and Pressure Cap.
SeeCoolant Surge Tank Pressure Cap on
page 393andCooling System on page 396.
K. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 386.
If your vehicle is equipped with front compartment
underhood sight shields, before closing the
hood be sure to reinstall the sight shields. To
reinstall the shields, locate the tabs on the left and
right sides and insert them into the openings in
the tower to tower brace. Then insert the fasteners
into the top of the shield and push the fasteners
back into place.
379

Notice:In cold weather, water can freeze and
crack the engine, radiator, heater core and
other parts. Use the recommended coolant and
the proper coolant mixture.
{CAUTION:
You can be burned if you spill coolant on
hot engine parts. Coolant contains
ethylene glycol and it will burn if the
engine parts are hot enough. Do not spill
coolant on a hot engine.
If no coolant is visible in the surge tank, add
coolant as follows:
1. Remove the coolant surge tank pressure cap
when the cooling system, including the
coolant surge tank pressure cap and upper
radiator hose, is no longer hot. Turn the
pressure cap slowly counterclockwise about
one-quarter of a turn. If you hear a hiss,
wait for that to stop. A hiss means there is still
some pressure left.2. Then keep turning the pressure cap slowly,
and remove it.
399

1. Remove the Intercooler System pressure cap
when the Intercooler System, including the
upper intercooler hoses, are no longer
hot. Turn the pressure cap slowly
counterclockwise about one-quarter of a turn.
If you hear a hiss, wait for that to stop.
This allows any pressure still left to be vented.
2. Then keep turning the pressure cap slowly,
and remove it.3. Add the proper DEX-COOL
®coolant mixture
to the ll neck, until the coolant reaches the
COLD FILL line on the ll neck.
4. With the Intercooler System pressure cap off,
start the engine and let it run for a couple of
minutes. Then turn the engine off. By this time,
the coolant level inside the ll neck may be
lower. If the level drops to where coolant is no
longer visible in the horizontal tube section
of the ll neck, with the engine off add more of
the DEX-COOL
®coolant mixture to the ll
neck until the level is again visible in the
horizontal tube section.
5. Then replace the pressure cap. Be sure the
pressure cap is hand-tight and fully seated.
If the coolant is not at the proper level
when the system cools down again, see
your dealer.
402

It is located between the battery and the
underhood fuse block. You should always use
this remote ground location, instead of the
terminal on the battery.
Notice:If you connect a negative cable to the
ECM, ECM mounting bracket, or any cables
that attach to the ECM bracket, you may
damage the ECM. Always attach the negative
cable to your vehicle’s remote negative ground
location, instead of the ECM, ECM bracket,
or any cables attached to the ECM bracket.
{CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.
{CAUTION:
Using a match near a battery can cause
battery gas to explode. People have been
hurt doing this, and some have been
blinded. Use a ashlight if you need more
light. Be sure the battery has enough
water. You do not need to add water to the
battery installed in your new vehicle. But if
a battery has ller caps, be sure the right
amount of uid is there. If it is low, add
water to take care of that rst. If you do not,
explosive gas could be present.
Battery uid contains acid that can burn
you. Do not get it on you. If you
accidentally get it in your eyes or on your
skin, ush the place with water and get
medical help immediately.
411

2. Pull out the push pins holding down the top
portion of the cloth cover.
3. Fold the cover down slightly and locate the
lamp assembly.
4. Turn the socket counterclockwise and pull it
straight out to remove it from the lamp
assembly.
5. Pull the old bulb straight out and reinstall the
new bulb.
6. Reverse the steps to reinstall.
Replacement Bulbs
Exterior Lamp Bulb Number
Back-up 3157K
For replacement bulbs not listed here, contact
your dealer.
Windshield Replacement
Keep in mind that your windshield is part of the
Head-Up Display (HUD) system. If you ever have
to get your windshield replaced, be sure to get
one that is designed for HUD or your HUD image
may look blurred or out of focus.
Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for
wear or cracking. SeeScheduled Maintenance
on page 505.
It’s a good idea to clean or replace the wiper
blade assembly on a regular basis or when worn.
For proper windshield wiper blade length and
type, seeNormal Maintenance Replacement Parts
on page 518.
419