2007 CADILLAC SRX ignition

Driving in Water
Heavy rain can mean ash ooding, and ood
waters demand extreme caution.
Find out how deep the water is before you drive
through it. If it is deep enough to cover your wheel
hubs, axles, or exhaust pipe, do not try it — you
probably will not get through. Also, water that deep
can damage the axle and other vehicle parts.
If the water is not too deep, drive slowly through it.
At faster speeds, water splashes on your
vehicle’s ignition system and your vehicle can
stall. Stalling can also occur if you get the tailpipe
under water. And, as long as the tailpipe is
under water, you will never be able to start the
engine. When you go through water, remember
that when the brakes get wet, it may take you
longer to stop.{CAUTION:
Driving through rushing water can be
dangerous. Deep water can sweep your
vehicle downstream and you and your
passengers could drown. If it is only
shallow water, it can still wash away the
ground from under your tires, and you
could lose traction and roll the vehicle
over. Do not drive through rushing water.
SeeDriving in Rain and on Wet Roads on
page 308for more information on driving through
water.
305

{CAUTION:
Coasting downhill in NEUTRAL (N) or with
the ignition off is dangerous. The brakes
will have to do all the work of slowing
down. They could get so hot that they
would not work well. You would then have
poor braking or even none going down a
hill. You could crash. Always have the
engine running and your vehicle in gear
when you go downhill.
Know how to go down hills. The most important
thing to know is this: let your engine do some of
the slowing down. Shift to a lower gear when
you go down a steep or long hill.
Know how to go uphill. You may want to shift
down to a lower gear. The lower gears help
cool your engine and transmission, and you can
climb the hill better.
Stay in your own lane when driving on two-lane
roads in hills or mountains. Do not swing wide
or cut across the center of the road. Drive at
speeds that let you stay in your own lane.
As you go over the top of a hill, be alert. There
could be something in your lane, like a stalled
car or an accident.
You may see highway signs on mountains that
warn of special problems. Examples are long
grades, passing or no-passing zones, a falling
rocks area, or winding roads. Be alert to these
and take appropriate action.
316

Notice:Ignoring these steps could result in
costly damage to your vehicle that would
not be covered by your warranty.
Trying to start your vehicle by pushing or
pulling it will not work, and it could damage
your vehicle.
1. Check the other vehicle. It must have a
12-volt battery with a negative ground system.
Notice:If the other vehicle’s system is not a
12-volt system with a negative ground,
both vehicles can be damaged. Only use
vehicles with 12-volt systems with negative
grounds to jump start your vehicle.
2. Get the vehicles close enough so the jumper
cables can reach, but be sure the vehicles are
not touching each other. If they are, it could
cause a ground connection you do not
want. You would not be able to start your
vehicle and the bad grounding could damage
the electrical systems.To avoid the possibility of the vehicles rolling,
set the parking brake rmly on both vehicles
involved in the jump start procedure. Put
an automatic transmission in PARK (P) or a
manual transmission in NEUTRAL before
setting the parking brake.
Notice:If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter or the accessory power
outlets. Turn off the radio and all lamps
that are not needed. This will avoid sparks
and help save both batteries. And it could
save the radio.
387

Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected for
wear or cracking. SeeScheduled Maintenance
on page 471for more information.
It’s a good idea to clean or replace the wiper
blade assembly on a regular basis or when worn.
For proper windshield wiper blade length and
type, seeNormal Maintenance Replacement Parts
on page 482.
To replace the wiper blade assembly, do the
following:
1. Turn the ignition to ON with the engine off.
2. Turn on the windshield wipers and turn them
off again when the wipers are in the out-wipe
position. The driver’s side blade will be
straight up and down on the windshield.
3. Pull the windshield wiper assembly away from
the windshield.4. Lift the wiper blade assembly up so it is in a
T-shaped position. You should be able to see
a tab.
5. Squeeze the tab together and pull the wiper
blade assembly down far enough to release it
from the J-hooked end of the wiper arm. Slide
the assembly away from the arm.
Allowing the wiper blade arm to touch the
windshield when no wiper blade is installed
could damage the windshield. Any damage that
occurs would not be covered by your warranty.
Do not allow the wiper blade arm to touch the
windshield.
397

Tire Pressure Monitor System
The Tire Pressure Monitor System (TPMS) uses
radio and sensor technology to check tire pressure
levels. If your vehicle has this feature, sensors
are mounted on each tire and wheel assembly,
except for the compact spare tire and wheel. The
TPMS sensors monitor the air pressure in your
vehicle’s tires and transmit the tire pressure
readings to a receiver located in the vehicle. The
TPMS is designed to alert the driver if a low
pressure condition exists.
Using the Driver Information Center (DIC), the
driver can also check tire pressure levels using the
DIC. For additional information and details about
the DIC operation and displays seeDIC Controls
and Displays on page 215andDIC Warnings
and Messages on page 220.When a low tire pressure condition is detected,
the TPMS illuminates the low tire pressure warning
symbol located in the instrument panel cluster,
and at the same time a DIC message to check the
pressure in a specic tire also appears on the
DIC display. The low tire pressure warning symbol
and the CHECK TIRE PRESSURE message on
the DIC display appear at each ignition cycle until
the tires are inated to the correct ination
pressure.
You may notice, during cooler weather conditions,
the low tire pressure warning light and DIC
warning message may come on when the vehicle
is rst started, and then turn off as you start to
drive. This could be an early indicator that the air
pressure in the tire(s) is getting low and needs
to be inated to the proper pressure.
410

The TPM matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON with the
engine off.
3. Using the DIC, press the vehicle information
button until the PRESS
VTO RELEARN
TIRE POSITIONS message displays.
4. Press the Set/Reset button. The horn sounds
twice to indicate the TPMS receiver is ready,
and the TIRE LEARNING ACTIVE message
displays. The TPMS low tire warning light
ashes throughout the matching procedure.
5. Start with the driver’s side front tire.
6. Remove the valve cap from the valve stem.
Activate the TPM sensor by increasing or
decreasing the tire’s air pressure for
10 seconds, or until a horn chirp sounds. The
horn chirp, which may take up to 30 seconds to
sound, conrms that the sensor identication
code has been matched to this tire position. To
decrease the tire’s air-pressure use the pointed
end of the valve cap, a pencil-style air pressure
gage, or a key.7. Proceed to the passenger’s side front tire, and
repeat the procedure in Step 6.
8. Proceed to the passenger’s side rear tire, and
repeat the procedure in Step 6.
9. Proceed to the driver’s side rear tire, and
repeat the procedure in Step 6.
10. After hearing the conrming horn chirp, for
the driver’s side rear tire, the horn sounds
two more times to signal the tire learning
model is no longer active. Turn the ignition
switch to OFF.
11. Set all four tires to the recommended air
pressure level as indicated on the tire and
loading information label.
12. Put the valve caps back on the valve stems.
The spare tire does not have a TPMS sensor.
If you replace one of the road tires with the spare,
the SERVICE TIRE MONITOR SYSTEM
message displays on the DIC screen. This
message should go off once you re-install the
road tire containing the TPMS sensor.
413

Relays Usage
FOG LAMP SS
MICROFront Fog Lamps
SPARE Spare
IGN MAIN SS
MICROIgnition Switch (ON)
STRTR HC
MICROStarter Solenoid
PWR/TRN HC
MICROPowertrain/Engine Control Module
HI BEAM SS
MICROHigh-Beam Headlamps
BLWR HC
MICROFront Blower Motor Assembly
WPR HC
MICROWindshield Wiper System - On/Off
WPR HI HC
MICROWindshield Wiper System -
Low/High
HEAD LAMP
WASH HC
MICROHeadlamp Washer Pump (Option)
LO BEAM-LP
MICRO/HID-HC
MICROLow-Beam Headlamps
REAR WASH
SS MICRORear Washer PumpRelays Usage
HORN SS
MICROHorn
A/C CMPRSR
CLTCH SS
MICROAir Conditioning Compressor Clutch
FUEL PUMP
SS MICROFuel Pump
ACCY SS
MICROAccessory Power (Rear Wipers,
Inside Rearview Mirror)
J Case Fuses Usage
FAN 2 Right Cooling Fan Motor
SPARE Spare
FAN 1 Left Cooling Fan Motor
SPARE Spare
STRTR Starter Solenoid
LPDB 2LRPDB (Left Side Rear
Power Distribution Box)
ABS MOTOR Anti-lock Brake System Module
LPDB 1LRPDB (Left Side Rear
Power Distribution Box)
RPDB 1RRPDB (Right Side Rear
Power Distribution Box)
SPARE Spare
457

J Case Fuses Usage
BLWR Front Blower Motor Assembly
RPDB 2RRPDB (Right Side Rear
Power Distribution Box)
Mini Fuses Usage
FRNT
WASHERFront Washer Pump
SPARE Spare
SPARE Spare
AIRBAGSensing Diagnostic Module (SDM),
Occupant Sensor Display,
Instrument Cluster
ABS IGNAnti-lock Braking System Ignition,
Variable Effort Steering
IGN SW Ignition Switch, Immobilizer Module
ECM/TCM IGNEngine Control Module/Transmission
Control Module Ignition Power
MISC IGN Air Quality Sensor
EMISSION 1Pre 02 Sensors, Cam Phasor (V6),
Canister Purge (V6), Intake Manifold
Tuning Valve (V6)
SPARE Spare
Mini Fuses Usage
DISPLAYInstrument Panel Cluster, Climate
Control Module, Front Blower Relay,
Diagnostic Link Connector
BCM 2LED Instrument Panel Dimming,
Overhead Lamps, Vanity Lamps
EVEN COILSEven Ignition Coils, Even Fuel
Injectors
BCM 6Right Side Rear Stoplamp, Turn
Lamps, Key Capture Solenoid
RADIO Radio
ODD COILSOdd Ignition Coils, Odd Fuel
Injectors
BCM 1 Body Control Module (BCM) Power
LT HI BEAM Left Side High-Beam Headlamp
BCM 7/CLOCK Switch Dimming, Analog Clock
SPARE Spare
EMISSION 2Cooling Fan Relays, Air
Conditioning Clutch Relay, Post O2
Sensors, Mass Airow Sensor,
Canister Purge (V8)
ECM BATT Engine Control Module (ECM)
458