2007 CADILLAC ESCALADE garage door opener

4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on constantly,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for
two seconds and then turns to a constant light,
continue with Steps 6 through 8 following to
complete the programming of a rolling-code
device, most commonly, a garage door opener.6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release. Repeat
the press/hold/release sequence a second
time, and depending on the brand of the
garage door opener or other rolling code
device, repeat this sequence a third time to
complete the programming.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” Do not
repeat Step 1, as this will erase all previous
programming from the Universal Home Remote
buttons.
176

Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds
of transmission. This may not be long enough
for Universal Home Remote to pick up the signal
during programming. Similarly, some U.S. gate
operators are manufactured to time out in
the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door
opener by using the “Programming Universal
Home Remote” procedures, regardless of where
you live, replace Step 3 under “Programming
Universal Home Remote” with the following:
Continue to press and hold the Universal Home
Remote button while you press and release every
two seconds (cycle) the hand-held transmitter
button until the frequency signal has been
successfully accepted by the Universal Home
Remote. The Universal Home Remote indicator
light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming
Universal Home Remote” to complete.
Using Universal Home Remote
Press and hold the appropriate Universal Home
Remote button for at least half of a second.
The indicator light will come on while the signal is
being transmitted.
Erasing Universal Home Remote
Buttons
To erase programming from the three Universal
Home Remote buttons do the following:
1. Press and hold down the two outside buttons
until the indicator light begins to ash, after
20 seconds. Do not hold the two outside
buttons for longer than 30 seconds.
2. Release both buttons.
The Universal Home Remote is now in the training
(learning) mode and can be programmed at any
time beginning with Step 2 under “Programming
Universal Home Remote” shown earlier in
this section.
Individual buttons cannot be erased, but they can
be reprogrammed. See “Reprogramming a
Single Universal Home Remote Button” following
this section.
177

Engine (cont.)
Overheating............................................. 422
Starting.................................................... 141
Entry Lighting.............................................. 213
Event Data Recorders (EDR)...................... 551
Exit Lighting................................................ 213
Extender, Safety Belt..................................... 59
Exterior Lamps............................................ 205
F
Filter
Engine Air Cleaner................................... 412
Finish Damage............................................ 504
Flashers, Hazard Warning........................... 194
Flat Tire...................................................... 476
Flat Tire, Changing...................................... 476
Flat Tire, Storing......................................... 492
Fluid
Automatic Transmission............................ 415
Power Steering........................................ 430
Windshield Washer.................................. 431
Fog Lamp Light........................................... 243
Fog Lamps.................................................. 212
Front Axle................................................... 445Fuel............................................................ 398
Additives.................................................. 399
California Fuel.......................................... 399
Filling a Portable Fuel Container.............. 403
Filling Your Tank...................................... 401
Fuels in Foreign Countries....................... 400
Gage....................................................... 244
Gasoline Octane...................................... 398
Gasoline Specications............................ 398
Fuses
Center Instrument Panel Fuse Block........ 510
Fuses and Circuit Breakers...................... 507
Instrument Panel Fuse Block................... 507
Underhood Fuse Block............................. 511
Windshield Wiper..................................... 507
G
Gage
Engine Coolant Temperature.................... 238
Fuel......................................................... 244
Speedometer........................................... 230
Tachometer.............................................. 230
Garage Door Opener..........................167, 168
Garment Hooks........................................... 179
564