Page 492 of 580

14. Tilt the tire retainer
at the end of the
cable and pull
it through the wheel
opening. Pull the
tire out from
under the vehicle.
15. Turn the wheel wrench in the hoist shaft hole
in the bumper clockwise to raise the cable
back up if the cable is hanging under
the vehicle.
Have the hoist assembly inspected as soon as
you can. You will not be able to store a spare or
at tire using the hoist assembly until it has
been replaced.
To continue changing the at tire, seeRemoving
the Flat Tire and Installing the Spare Tire on
page 482.Storing a Flat or Spare Tire and
Tools
{CAUTION:
Storing a jack, a tire, or other equipment
in the passenger compartment of the
vehicle could cause injury. In a sudden
stop or collision, loose equipment could
strike someone. Store all these in the
proper place.
Notice:Storing an aluminum wheel with a at
tire under your vehicle for an extended
period of time or with the valve stem pointing
up may damage the wheel. Always stow
the wheel with the valve stem pointing down
and have the wheel/tire repaired as soon
as possible.
492
Page 493 of 580
Store the tire under the rear of the vehicle in the
spare tire carrier. Refer to the following graphics
and instructions to help you:
A. Spare Tire/Flat
Tire (Valve Stem
Pointed Down)
B. Hoist Assembly
C. Hoist Cable
D. Tire Retainer
E. Hoist ShaftF. Hoist End of
Extension Tool
G. Hoist Shaft
Access Hole
H. Wheel Wrench
I. Jack Handle Extension
J. Spare Tire Lock1. Put the tire (A) on the ground at the rear of
the vehicle with the valve stem pointed
down, and to the rear.
2. Tilt the tire
retainer (D)
downward and
through the wheel
opening. Make
sure the retainer is
fully seated
across the underside
of the wheel.
3. Assemble the two jack handle extensions (I)
and wheel wrench (H) as shown.
493
Page 494 of 580
4. Insert the open end
of the extension (F)
through the hole
in the rear
bumper (G) (hoist
shaft access hole).
5. Raise the tire part way upward. Make sure the
retainer is seated in the wheel opening.
6. Raise the tire fully against the underside of
the vehicle by turning the wheel wrench
clockwise until you hear two clicks or feel it
skip twice. You cannot overtighten the cable.7. Make sure the tire is stored securely. Push,
pull (A), and then try to turn (B) the tire. If the
tire moves, use the wheel wrench to tighten
the cable.
8. Reinstall the spare tire lock.
9. Close the hoist shaft access cover.
494
Page 495 of 580

To store the tools, follow these steps:
1. Return the tools to the tool bag and place it
back in the top-box storage unit.
2. Assemble the wheel blocks and jack together
with the wing nut by reversing Step 2 under
Removing the Spare Tire and Tools on
page 478.
3. Replace the jack cover and tighten the
jack-cover wing nuts.
Spare Tire
Your vehicle, when new, had a fully-in ated spare
tire. A spare tire may lose air over time, so check its
in ation pressure regularly. SeeIn ation - Tire
Pressure on page 460andLoading Your Vehicle on
page 372for information regarding proper tire
in ation and loading your vehicle. For instruction on
how to remove, install, or store a spare tire, see
Removing the Flat Tire and Installing the Spare Tire
on page 482andStoring a Flat or Spare Tire and
Tools on page 492.After installing the spare tire on your vehicle, you
should stop as soon as possible and make
sure the spare is correctly in ated. Have the
damaged or at road tire repaired or replaced as
soon as you can and installed back onto your
vehicle. This way, a spare tire will be available in
case you need it again.
Your vehicle may have a different size spare tire
than the road tires, those originally installed on your
vehicle. This spare tire was developed for use on
your vehicle, so it is all right to drive on it.
495
Page 577 of 580