2007 CADILLAC DTS display

At distances less than 12 inches (0.3 m), a
chime will sound for a short time and all three
lights (amber/amber/red) will be lit and ashing.
When you are backing the vehicle and objects are
detected at the same time near both the front
and rear bumpers, both color-coded light displays
will notify you of objects close to each bumper.
If there are objects detected near both bumpers,
the beeps will only be sounded to notify that
objects are close to the rear bumper. However,
if while you are backing and an object comes
within 1 ft (0.3 m) of the front bumper, and at the
same time there is another object further than
1 ft (0.3 m) from the rear bumper, then the beeps
will only be sounded to notify you of the closer
object that is near the front bumper.When the System Does Not Seem to
Work Properly
If the UFRPA system will not activate due to a
temporary condition, the message PARKING
ASSIST OFF will be displayed on the DIC and a
red light will be shown on the rear UFRPA display
when the shift lever is moved into REVERSE (R).
This occurs under the following conditions:
The driver disables the system. SeeDIC
Controls and Displays on page 240.
The parking brake pedal is depressed.
A trailer was attached to your vehicle, or a
bicycle or an object was hanging out of your
trunk during your last drive when you turned off
the vehicle. If the attached objects are removed
from your vehicle before the start of your next
drive, the system will return to normal operation
unless an object is detected when the vehicle is
shifted out of park. If this occurs, you will have
to wait until the vehicle is driven forward above
15 mph (25 km/h) before UFRPA will return to
normal operation.
206

A bicycle or an object is attached to the front
bumper during your last drive when you turned
off the vehicle. If the attached objects are
removed from your vehicle before the start of
your next drive, the system will return to normal
unless an object is detected when the vehicle is
shifted out of park. If this occurs, UFRPA will
return to normal operation when the vehicle is
driven forward above 15 mph (25 km/h).
The ultrasonic sensors are not kept clean.
So be sure to keep your vehicle’s front and rear
bumpers free of mud, dirt, snow, ice and slush.
For cleaning instructions, seeWashing Your
Vehicle on page 444. If after cleaning the front
and rear bumpers and driving forward at a
speed of at least 15 mph (25 km/h), the DIC
displays the PARKING ASSIST OFF message,
see your dealer/retailer.
Other conditions that may affect system
performance include vibrations from a
jackhammer or the compression of air
brakes on a very large truck or other
mechanical devices that interfere with
UFRPA performance.
When UFRPA is disabled without driver action
and the driver attempts to turn UFRPA back
on using the Driver Information Center (DIC),
the PARKING ASSIST ON option will not be
selectable if the necessary conditions stated
above for normal system operation are not met.
As always, drivers should use care when backing
up a vehicle. Always look behind you, being
sure to check for other vehicles, obstructions
and blind spots.
For Driver Information Center messages related
to UFRPA, seeDIC Warnings and Messages
on page 246.
If the bumper is damaged, your UFRPA system
may not work properly. Take the vehicle to
your dealer/retailer to repair the system.
207

After the vehicle is started, the display will
show the interior temperature settings and the
outside temperature.
If the AUTO position is selected on the fan or mode
control, the system will automatically control the air
conditioning compressor. The A/C compressor will
run automatically even at cool outside temperatures
in order to dehumidify the air. The A/C indicator
light will be lit when the system is operating
automatically, even at near freezing outside
temperatures. Press the A/C button on the fan
control to turn off the A/C. For improved window
clearing performance in defog or defrost modes,
the A/C compressor will run automatically.
h(AUTO RECIRCULATION):If the AUTO
position is selected on either the fan or mode
control, the system will automatically control the air
inlet to supply fresh outside air or recirculate the
interior air to cool the car faster. The indicator light
on the recirculation button will light whenever the
system switches to recirculation. You may force
outside air by pressing the recirculation button
when the light is lit. For vehicles without rear climate
controls, press the outside air button to force
outside air. The next time AUTO fan or mode is
selected, the air inlet will reset back to AUTO
operation.
Manual Operation
9(Fan):Turn the left control either to the left or
right to adjust the fan speed. Turning this control
completely counterclockwise will turn on the
automatic fan operation. Turning this control to the
“O” position will turn the climate control system off.
If the airow seems low when the fan speed is at
the highest setting, the passenger compartment air
lter may need to be replaced. SeePassenger
Compartment Air Filter on page 220.
9(Off):Turn the left control to this position to
turn the entire climate control system off.
To change the current mode, select one of the
following positions using the right control:
AUTO:Turn the control to this position to turn on
the automatic delivery mode operation.
F(Vent):Turn the control to this mode to direct
air to the instrument panel outlets.
*(Bi-Level):Turn the control to this mode to
direct approximately half of the air to the instrument
panel outlets and most of the remaining air to the
oor outlets. In automatic operation, cooler air is
directed to the upper outlets and warmer air to the
oor outlets.
212

There is also an interior
temperature sensor
located next to the
steering wheel that
measures the
temperature of the air
inside your vehicle.
There is also an exterior temperature sensor
located behind the front grille. This sensor reads
the outside air temperature and helps maintain
the temperature inside the vehicle. Any cover
on the front of the vehicle could cause a
false reading in the displayed temperature.In order to prevent false temperature readings
at start up, the displayed temperature will
not change until the following occurs:
Vehicle speed is above 10 mph (16 kmh) for
5 minutes.
Vehicle speed is above 32 mph (51 kmh) for
2 and a half minutes.
The climate control system uses the information
from these sensors to maintain your comfort
setting by adjusting the outlet temperature, fan
speed, and the air delivery mode. The system may
also supply cooler air to the side of the vehicle
facing the sun. The recirculation mode will also
be used as needed to maintain cool outlet
temperatures.
215

Automatic Operation
«A ª(Fan):Press this button until AUTO
appears on the display to place the system in
automatic mode. When automatic operation is
active, the system will automatically control the fan
speed. If in auto fan mode, pressing the up arrow
button will cancel automatic operation and places
the system in manual mode. If in auto mode,
pressing the down arrow will turn the rear climate
control system off.
«Nª(Mode):Press the this button until
AUTO appears on the display to place the system
in automatic mode. When automatic operation
is active, the system will automatically control
the air delivery mode.
Manual Operation
«A ª(Fan):Press these up or down arrow
buttons to increase or decrease the fan speed.
«bª(Temperature):Press these up or
down arrow buttons to increase or decrease the
temperature for the rear seat passengers. Once the
rear setting temperature is altered from followingthe front setting temperature, it will no longer follow
changes to the front setting temperature until the
front climate control AUX button resets it.
«Nª(Mode):Press these buttons to change
the air delivery mode. If in AUTO air delivery
mode, pressing the up arrow button will cancel
automatic operation and place the system in
manual mode.
Y(Vent):This mode directs air to the upper
outlets.
%(Bi-Level):This mode directs half the air
to the upper outlets, and the other half to the oor
outlets.
[(Floor):This mode directs the air to the oor
outlets.
For more information on how to use the front
climate control system, seeDual Climate Control
System on page 210.
For more information on the air outlets, seeOutlet
Adjustment on page 217. Be sure to keep the
area under the front seats clear of any objects
so that the air inside of your vehicle can circulate
effectively.
219

Speedometer and Odometer
The speedometer lets you see your speed
in both miles per hour (mph) and kilometers
per hour (km/h). See “MPH (km)” underDIC
Controls and Displays on page 240for more
information.
The odometer mileage can be checked without
the vehicle running. Your vehicle’s odometer
works together with the driver information center.
You can set a Trip A and a Trip B odometer.
See “Trip Fuel” underDIC Controls and Displays
on page 240for more information.
If your vehicle ever needs a new odometer
installed, the new one will be set to the correct
mileage total of the old odometer.
Tachometer
This gage indicates
the engine speed in
revolutions per
minute (rpm).
224

Airbag Readiness Light
There is an airbag readiness light on the instrument
panel, which shows the airbag symbol. The system
checks the airbag’s electrical system for
malfunctions. The light tells you if there is an
electrical problem. The system check includes the
airbag sensors, the airbag modules, the wiring and
the diagnostic module. For more information on the
airbag system, seeAirbag System on page 70.
This light will come on
when you start your
vehicle, and it will ash
for a few seconds.
Then the light should
go out. This means
the system is ready.
If the airbag readiness light stays on after you
start the vehicle or comes on when you are driving,
your airbag system may not work properly.
Have your vehicle serviced right away.{CAUTION:
If the airbag readiness light stays on after
you start your vehicle, it means the airbag
system may not be working properly. The
airbags in your vehicle may not inate in
a crash, or they could even inate without
a crash. To help avoid injury to yourself
or others, have your vehicle serviced right
away if the airbag readiness light stays on
after you start your vehicle.
The airbag readiness light should ash for a
few seconds when you turn the vehicle on. If the
light does not come on then, have it xed so it
will be ready to warn you if there is a problem.
If there is a problem with the airbag system in
your vehicle, the SERVICE AIR BAG message will
appear on the DIC display. SeeDIC Warnings
and Messages on page 246andSafety Belt
Pretensioners on page 41for more information.
226

Charging System Light
When you turn the
engine on, this light
will come on briey to
show that the generator
and battery charging
systems are working
properly.
If this light stays on, your vehicle needs service.
You should take your vehicle to the dealer/retailer
at once. To save the battery until you get there,
turn off all accessories. SeeDIC Controls and
Displays on page 240for more information.
Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part isn’t working, the
other part can still work and stop you. For good
braking, though, you need both parts working well.
If the warning light comes on, there is a brake
problem. Have your brake system inspected
right away.
This light should come on briey when you turn
the engine on. If it does not come on then, have it
xed so it will be ready to warn you if there is a
problem.
United StatesCanada
229