2007 CADILLAC CTS V change time

The air-conditioning system removes moisture
from the air, so you may sometimes notice a small
amount of water dripping underneath your
vehicle while idling or after turning off the engine.
This is normal.
Do not cover the solar sensor located in the
center of the instrument panel, near the
windshield. For more information on the solar
sensor, see “Sensors” later in this section.
Manual Operation
yNz(Mode):Pressing the mode switch and
changing the mode cancels automatic operation
and places the system in manual mode. Press
AUTO to return to automatic operation.
The outboard air outlets will always receive airow
regardless of the mode selected. SeeOutlet
Adjustment on page 194to change this airow
from the outboard outlets.To change the current mode, select one of the
following:
Y(Vent):This mode directs air to the instrument
panel outlets.
\(Bi-Level):This mode directs approximately
half of the air to the instrument panel outlets,
and then directs most of the remaining air to the
oor outlets. In automatic operation, cooler air
is directed to the upper outlets and warmer air to
the oor outlets.
[(Floor):This mode directs most of the air to
the oor outlets with some air directed to the
outboard outlets (for the side windows), and a little
air directed to the windshield.
The mode switch can also be used to select the
defog mode. Information on defogging and
defrosting can be found later in this section.
yAz(Fan):Press this switch to increase or
decrease the fan speed. Pressing this switch
cancels automatic operation and places the system
in manual mode. Press AUTO to return to
automatic operation.
190

Vehicle Information Menu Item
Descriptions
The following paragraphs contain a more detailed
description of each menu item:
OUTSIDE TEMP:If you select this item, the
current outside temperature is displayed at the top
of the screen. It will be in either degrees
Fahrenheit (°F) or degrees Celsius (°C) depending
upon whether the system is set for English or
metric units. If you wish to change the units, see
DIC Main Menu on page 228.
MI TRIP A and B (KM TRIP A and B):For
information on the trip odometers, seeTrip
Odometers on page 200.
MILES RANGE (KM RANGE):If you select this
item, the approximate number of remaining
miles or kilometers you can drive without refueling
is displayed. This estimate is based on the
current driving conditions and will change if the
driving conditions change. For example, if you are
driving in traffic making frequent stops, the
display may read one number, but if you enter the
freeway, the number may change even thoughyou still have the same amount of gas in the gas
tank. This is because different driving conditions
produce different fuel economies. Generally,
freeway driving produces better fuel economy than
city driving.
If your vehicle is low on fuel, the Fuel Level Low
message will be displayed. See “Fuel Level
Low” underDIC Warnings and Messages on
page 232for more information.
MPG AVG (L/100 KM AVG):If you select this
item, the approximate average miles per
gallon (mpg) or liters per 100 kilometers (L/100 km)
is displayed. This number is calculated based
on the number of mpg (L/100 km) recorded since
the last time this menu item was reset.
To reset the MPG AVG (L/100 KM AVG), press
the CLR button located to the right of the screen.
The display will return to zero.
MPG INST (L/100 KM INST):If you select this
item, the current fuel economy is displayed. This
number reects only the fuel economy that the
vehicle has right now and will change frequently as
driving conditions change. Unlike average fuel
economy, this menu item cannot be reset.
225

8(Clock):Use this menu item to set the time on
the clock.
SeeSetting the Time on page 259for more
information.
8/4(Clock/Information Display):Use this
menu item to toggle between the clock display and
the XM™ Information (Song, Artist, Album), if
available.
SeeSetting the Time on page 259and “XM™
Satellite Radio Service” underRadio with CD on
page 260for more information.
SETUP:When you select this menu item, the
following submenu is available:
LANGUAGE
PERSONALIZATION
CONFIGURE DISPLAY KEYS
CONFIGURE SWC (Steering Wheel
Control) KEYS
To change the language displayed on the radio,
select LANGUAGE by pressing the TUNE/SEL
knob. Turn the TUNE/SEL knob to scroll through
the available languages and press the knob tomake your selection. If you accidentally select a
language that you did not want, ENGLISH is
always at the top of the language list.
For more information on the other items in the
SETUP menu, seeDIC Vehicle Personalization on
page 242andRecongurable Steering Wheel
Controls (SWC) (CTS) on page 169.
DIC Warnings and Messages
These messages will appear if there is a problem
detected in one of your vehicle’s systems.
You must acknowledge a message to clear it from
the screen for further use. To clear a message,
press the CLR button.
Be sure to take any message that appears on the
screen seriously and remember that clearing
the message will only make the message
disappear, not the problem.
Battery Not Charging
When this message appears on the display, there
is a problem with the generator and battery
charging systems. Have the electrical system
checked by your dealer as soon as possible.
232

Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until AUTO EXIT
SEAT is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark will
appear in the box next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.Twilight Delay
This feature allows you to set the amount of time
you want the exterior lamps to remain on after
you exit the vehicle.
Programmable Modes
Mode 1:0:00 seconds
Mode 2:0:15 seconds
Mode 3:0:30 seconds
Mode 4:1:00 minute
Mode 5:1:30 minutes
Mode 6:2:00 minutes
Mode 7:2:30 minutes
Mode 8:3:00 minutes
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since the vehicle left the factory.
248

To determine the mode to which the vehicle is
programmed or to program the vehicle to a
different mode, use the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until TWILIGHT
DELAY is highlighted.
3. Press the TUNE/SEL knob to scroll through
and select the available delay settings.
If you choose Mode 1, the exterior lamps will
not illuminate when you exit the vehicle.
Only one mode can be selected at a time.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Lights Flash at Unlock
This feature ashes the exterior lamps when the
Remote Keyless Entry (RKE) transmitter is used to
unlock the vehicle. The lamps will ash for about
20 seconds unless a door is opened, the ignition is
turned to ACCESSORY, ON, or START, or the RKE
transmitter is used to lock the vehicle.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until LIGHTS
FLASH AT UNLOCK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
249

XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada.
XM™ offers a large variety of coast-to-coast
channels including music, news, sports, talk,
traffic/weather (U.S. subscribers), and children’s
programming. XM™ provides digital quality
audio and text information that includes song title
and artist name. A service fee is required in
order to receive the XM™ service. For more
information, contact XM™; In the U.S. at
www.xmradio.com or call 1-800-852-XMXM (9696)
or in Canada at www.xmradio.ca or call
1-877-GET-XMSR (438-9677).
CLOCK/INFO DISP (Clock/Information Display):
Press the CLOCK/INFO DISP button to switch
between the clock display, the XM™ screen, and
the XM™ information display.Press this button while in XM™ mode to retrieve
three different categories of information related
to the current song or channel: Artist, Song Title,
and Category. To view this information, perform
the following:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until CLOCK/INFO
DISP appears on the display.
3. Press the TUNE/SEL knob to select
CLOCK/INFO DISP. The display changes to
show the additional XM™ information.
4. To return to the original display, press the
CLR (clear) button or wait for the display to
time out.
If the CLOCK/INFO DISP is congured into one of
the congurable keys, pressing the key switches
the display between the radio station frequency
and the time. See “Congurable Radio Display
Keys” later in this section for more information.
261

Playing the Radio
PWR (Power):Press this knob to turn the system
on and off.
VOL (Volume):Turn this knob to increase or to
decrease the volume.
AVC (Automatic Volume Compensation):
Available only with the premium Bose
®audio
system. AVC, which utilizes Bose AudioPilot®
noise compensation technology, continuously
adjusts the audio system equalization, to
compensate for background noise, so that your
music always sounds the same at the set volume
level. This feature is most effective at lower
radio volume settings where background noise
can affect how well you hear the music being
played through your vehicle’s audio system.
At higher volume settings, where the music is
much louder than the background noise, there may
be little or no adjustments by AVC. To turn AVC
on and off, perform the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until AUTO
VOLUME COMP. appears on the display.3. Press the TUNE/SEL knob to turn AVC on or
off. An X appears in the box when AVC is
selected on.
4. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
For additional information on AudioPilot
®, please
visit www.bose.com/audiopilot.
SOURCE:Press this button to select a source,
either radio or CD. The CD must be loaded to select
the source and to play. CD appears on the display if
a CD is loaded. If a CD is not loaded the display
does not change from the radio source.
Finding a Station
BAND:Press this button to select FM1, FM2, AM,
or XM1 or XM2 (if equipped).
QSEEKR:Press the up or the down arrow to
go to the next or to the previous station and
stay there. SEEK appears on the display.
The sound mutes while seeking.
The radio only seeks stations with a strong signal
that are in the selected band.
262

F3 RDM (Random):Press this rm key to listen
to the tracks in random, rather than sequential,
order. RANDOM appears on the display.
Press RDM again to turn off random play.
RANDOM disappears from the display.
F4 RPT (Repeat):Press this rm key to hear a
track over again. REPEAT appears on the display.
Press RPT again to turn off repeat play. REPEAT
disappears from the display.
F6 DISP (Display):Press this rm key to display
the time of the track. Press this rm key again
to remove the time of the track from the display.
QSEEKR:Press the up or the down arrow to go
to the next or to the previous track on the CD.
QSCANR:Press this button to listen to each
track for 10 seconds. The CD goes to a track,
plays for 10 seconds, then goes to the next track.
Press this button again to stop scanning.
X(Eject):Press this button to stop a CD when
it is playing or to eject a CD when it is not
playing. Eject may be activated with the ignition
and the radio off.
Using the Six-Disc CD Changer
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There may be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check the
bottom surface of the CD. If the surface of the CD
is damaged, such as cracked, broken, or
scratched, the CD will not play properly. If the
surface of the CD is soiled, seeCare of Your CDs
on page 283for more information.
If there is no apparent damage, try a known
good CD.
272