2007 CADILLAC CTS V lock

{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack, you could be badly injured or
killed. Never get under a vehicle when it is
supported only by a jack.
{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall. To
help avoid personal injury and vehicle
damage, be sure to place the jack in the
proper location before raising the vehicle.
If you ever use a jack to lift your vehicle, follow
the instructions that came with the jack, and
be sure to use the correct lifting points to avoid
damaging your vehicle.Notice:Lifting your vehicle improperly can
damage your vehicle and result in costly repairs
not covered by your warranty. To lift your
vehicle properly, follow the advice in this part.
To help prevent vehicle damage:
Be sure the jack you are using meets the
weight standards for your vehicle and is
in good working order.
Be sure to place a block or pad between
the jack and the vehicle.
Make sure the jack you are using only
contacts the jacking location lift points and
is not leaning on any other vehicle
components such as the rocker panels, the
oor pan, or the stone guard moldings.
Lift only in the areas shown in the following
pictures.
419

Lifting From the Front
The front lifting points can be accessed from
either side of your vehicle, behind the front tires.1. Locate the front lifting points using the
diagram shown above and corresponding
triangular-shaped hoisting notches located in
the plastic molding. The front lifting location
is about 14 inches (35.6 cm) from the
rear edge of the front wheel well.
2. Be sure to place a block or pad between the
jack and the vehicle.
3. Lift the vehicle with the jack, making sure the
jack is centered on the front lifting point.
420

Lifting From the Rear
The rear lifting points can be accessed from either
side of your vehicle, in front of the rear tires.1. Locate the rear lifting points using the
diagram shown above and corresponding
triangular-shaped hoisting notches located in
the plastic molding. The rear lifting location
is about 7 inches (17.8 cm) from the
front edge of the rear wheel well.
2. Be sure to place a block or pad between the
jack and the vehicle.
3. Lift the vehicle with the jack, making sure the
jack is centered on the rear lifting point.
SeeDoing Your Own Service Work on page 333
for additional information.
421

Changing a Flat Tire (CTS Only)
If a tire goes at, avoid further tire and wheel
damage by driving slowly to a level place. Turn on
your hazard warning ashers.
{CAUTION:
Changing a tire can be dangerous. The
vehicle can slip off the jack and roll over
or fall on you or other people. You and
they could be badly injured or even killed.
Find a level place to change your tire.
To help prevent the vehicle from moving:
1. Set the parking brake rmly.
2. Put an automatic transmission shift
lever in PARK (P), or shift a manual
transmission to FIRST (1) or
REVERSE (R).
3. Turn off the engine and do not restart
while the vehicle is raised.
4. Do not allow passengers to remain in
the vehicle.
CAUTION: (Continued)
CAUTION: (Continued)
Put the wheel blocks at the front and rear of
the tire farthest away from the one being
changed. That would be the tire on the other
side, at the opposite end of the vehicle.
When you have a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.
424

Removing the Spare Tire and Tools
(CTS Only)
The equipment you will need is in the trunk.
To gain access to the spare tire and jacking
equipment, do the following:
1. Turn the wing nut on
the compact spare
tire cover
counterclockwise to
remove it. Then
remove the cover.
2. Turn the nut holding the jack counterclockwise
and remove it. Then remove the jack and
wheel wrench.
3. Remove the compact spare tire. SeeCompact
Spare Tire (CTS Only) on page 434for more
information about the compact spare tire.
425

Notice:If you position the jack under the
rocker molding and attempt to raise the
vehicle, you could break the molding and/or
cause other damage to your vehicle. Always
position the jack so that when the jack head is
raised, it will t rmly in the notch located
inboard from the rocker molding.
4. Turn the wheel wrench counterclockwise to
lower the jack lift head until the jack ts
under the vehicle.
5. Raise the jack by turning the wheel wrench
clockwise until the slots in the jack head t
into the metal ange located behind the
triangle on the plastic molding as shown.
6. Put the compact spare tire near you.
429

7. Raise the vehicle by turning the wheel wrench
clockwise. Raise the vehicle far enough off
the ground for the compact spare tire to
t under the vehicle.8. Remove all the
wheel nuts and take
off the at tire.
{CAUTION:
Rust or dirt on the wheel, or on the parts
to which it is fastened, can make the
wheel nuts become loose after time.
The wheel could come off and cause an
accident. When you change a wheel,
remove any rust or dirt from the places
where the wheel attaches to the vehicle.
CAUTION: (Continued)
430

CAUTION: (Continued)
In an emergency, you can use a cloth or a
paper towel to do this; but be sure to use
a scraper or wire brush later, if needed, to
get all the rust or dirt off.
{CAUTION:
Never use oil or grease on studs or nuts.
If you do, the nuts might come loose.
Your wheel could fall off, causing a
serious accident.9. Remove any rust or
dirt from the wheel
bolts, mounting
surfaces, and spare
wheel.
10. Install the spare tire.
11. Put the wheel nuts back on with the rounded
end of the nuts toward the wheel.
12. Tighten each wheel nut by turning it clockwise
with your hand until the wheel is held against
the hub.
431