2007 BUICK TERRAZA turn signal

Q(Lock):To lock all doors and the liftgate,
press the lock button on the remote keyless entry
transmitter. SeePower Door Locks on page 107
for more details on the power door lock features. If
your vehicle has the content theft-deterrent
system, the remote keyless entry transmitter’s lock
button may arm the system. SeeContent
Theft-Deterrent on page 124for more details.
When you use the remote keyless entry transmitter
to lock your vehicle, the turn signal lamps may
ash to let you know the command has been
received. If you press the lock button again, within
ve seconds, the horn will sound and the turn
signal lamps may ash to let you know the vehicle
is already locked. See “FOB LOCK FEEDBACK”
underDIC Vehicle Personalization (Uplevel
Only) on page 249for additional information.
"(Unlock):When you press unlock on the
remote keyless entry transmitter, only the driver’s
door will unlock. If you press unlock again
within ve seconds, all the doors and the liftgate
will unlock. If you would like all the doors to unlock
the rst time you press unlock, see “FOB
UNLOCK ON 1ST PRESS” underDIC Vehicle
Personalization (Uplevel Only) on page 249.If your vehicle has the content theft-deterrent
system, the unlock button on the remote keyless
entry transmitter will disarm the system. See
Content Theft-Deterrent on page 124for more
details.
When you use your remote keyless entry
transmitter to unlock your vehicle the turn signal
lamps will ash to let you know the command was
received.
L(Remote Alarm):When you press the horn
button on the remote keyless entry transmitter, the
turn signal lamps will ash and the horn will
sound. This will allow you to attract attention, if
needed.
Press this button again to stop the alarm from
sounding.
100

To start the engine using the remote start feature,
do the following:
1. Aim the remote keyless entry transmitter,
equipped with the remote vehicle start
button, at the vehicle.
2. Press and release the transmitter’s lock
button, then immediately press and hold
the remote vehicle start button until the
vehicle’s turn signal lamps ash, or for at
least two seconds, if the vehicle’s lights are
not visible. The vehicle’s doors will be locked.
3. When the vehicle’s engine starts, the parking
lamps will turn on and remain on while the
engine is running.
After a remote start, the engine will automatically
shut off after 10 minutes unless a time extension
has been done or the vehicle’s key is inserted into
the ignition switch and turned to RUN.The maximum number of remote starts or remote
start attempts between ignition cycles with the
key is two.
If the remote start procedure is used again before
the rst 10 minute time frame has ended, the
rst 10 minutes will immediately expire and
the second 10 minute time frame will start.
After two remote starts have been provided, the
vehicle’s ignition switch must be turned to
RUN and then back to LOCK using the key before
the remote start procedure can be used again.
If you enter the vehicle after a remote start,
and the engine is running, insert the key into the
ignition switch and turn it to the RUN position
to drive the vehicle.
104

Delayed Locking
This feature allows the locking of the vehicle to be
delayed until all doors have been closed for
approximately ve seconds.
To activate the delayed locking feature, do one of
the following:
Press the driver’s door power lock switch one
time while the driver’s door is open.
Press the passenger’s door power lock switch
one time while the passenger’s door is open.
Press the lock button on the remote keyless
entry transmitter one time while any door
is open.
Two chimes will sound to signal that delayed
locking is active.
The doors may be locked immediately by repeating
any of the above actions more than one time.If a door remains open, without any other door
being opened or closed, the vehicle will lock after
approximately 45 seconds.
If the key is in the ignition, this feature will not lock
the doors.
To turn the delayed locking feature off or on, see
DIC Vehicle Personalization (Uplevel Only) on
page 249.
Sliding Door Delayed Locking
If either sliding door is open when you use the
power door locks to lock the vehicle, the sliding
door that is open will not lock. Normally the
delayed locking feature will be used to lock the
sliding door after it has been closed.
The sliding door delayed locking feature will lock
your sliding door(s) in situations where the delayed
locking feature does not apply or was overridden
or programmed to be off. See “Delayed Locking”
earlier in this section. Shortly after the last
sliding door is closed, all the doors will lock.
108

Content Theft-Deterrent
Your vehicle has a theft-deterrent alarm system.
A light located on top of your instrument panel,
near the center of the vehicle next to the
windshield, will ash slowly to let you know that
the system has been armed.
While armed, the doors will not unlock with the
power door lock switch.Once armed, the alarm will go off if someone tries
to enter the vehicle without using the remote
keyless entry transmitter or a key, or turns
the ignition to RUN. The horn will sound and the
turn signal lamps will ash for up to two minutes.
Arming with the Power Lock Switch
Your alarm system will arm when the key is
removed from the ignition and you use the driver’s
power door lock switch, with the driver’s door
open or the passenger’s door power door
lock switch with the passenger’s door open to lock
the vehicle. If you would like to turn on power
door lock switch arming, seeDIC Vehicle
Personalization (Uplevel Only) on page 249
When the security light ashes quickly the system
is arming. After all doors and the liftgate are
closed and locked, the security light will begin
ashing at a very slow rate to let you know
the system is armed.
124

Arming with the Remote Keyless Entry
Transmitter
Your alarm system will arm if the key is not in the
ignition and you use your remote keyless entry
transmitter to lock the doors. The security light will
ash to let you know the system is arming. If
you press the transmitter’s lock button twice within
5 seconds, the horn will sound. After all doors
and the liftgate are closed and locked, the security
light will begin ashing at a very slow rate to let
you know the system is armed.
Arming with Your Key
Your alarm system will arm when you use your
key to lock the driver’s door. The security light will
ash to let you know the system is arming.
After all doors and the liftgate are closed and
locked, the security light will begin ashing at a
very slow rate to let you know the system is
armed. If you would like your key not to arm the
system, seeDIC Vehicle Personalization (Uplevel
Only) on page 249.
Arming Conrmation
If remote unlock conrmation is on, the turn signal
lamps will ash briey to let you know when
your alarm system has disarmed. If you would not
like the turn signal lamps to ash, seeDIC
Vehicle Personalization (Uplevel Only) on
page 249.
Disarming with the Remote Keyless
Entry Transmitter
Your alarm system will disarm when you use your
remote keyless entry transmitter to unlock the
doors. The security light will stop ashing to let you
know the system is no longer armed.
Disarming with Your Key
Your alarm system will disarm when you use your
key to unlock the driver’s door. The security
light will stop ashing to let you know the system
is no longer armed. If you would like your key
not to disarm the alarm system, seeDIC Vehicle
Personalization (Uplevel Only) on page 249.
125

5. After entering the switch settings, press and
release all three buttons at the same time.
The indicator lights will turn on.
6. Press and hold the button you would like to
use to control the garage door until the
garage door moves. The indicator light above
the selected button should slowly blink.
You may need to hold the button from ve to
55 seconds.
7. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
8. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1 through 8, choosing
a different function button in Step 7 than what
you used for the garage door opener.Programming Universal Home
Remote — Rolling Code
Rolling code garage door openers are used for
garage doors produced after 1996 and are
code protected. Rolling code means the coded
signal is changed every time your remote control
garage door opener is used.
Programming a rolling code garage door opener
involves time-sensitive actions, so read the
entire procedure before you begin. If you do not
follow these actions, the device will time out
and you will have to repeat the procedure.
Follow these steps to program up to
three channels:
1. Press the two outside buttons at the same
time for one to two seconds, and immediately
release them.
152

4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.” Do
not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for two
seconds and then turns to a constant light,
continue with Steps 6 through 8 following
to complete the programming of a rolling-code
device, most commonly, a garage door
opener.6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.
7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release.
Repeat the press/hold/release sequence a
second time, and depending on the brand of
the garage door opener or other rolling
code device, repeat this sequence a third time
to complete the programming.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” Do not
repeat Step 1, as this will erase all previous
programming from the Universal Home Remote
buttons.
156

Instrument Panel Overview........................ 170
Hazard Warning Flashers.......................... 172
Other Warning Devices............................. 172
Horn.......................................................... 172
Tilt Wheel.................................................. 172
Turn Signal/Multifunction Lever.................. 173
Turn and Lane-Change Signals................. 173
Headlamp High/Low-Beam Changer.......... 174
Flash-to-Pass............................................ 174
Windshield Wipers..................................... 175
Windshield Washer.................................... 175
Rear Window Wiper/Washer...................... 176
Cruise Control........................................... 177
Exterior Lamps.......................................... 181
Wiper Activated Headlamps....................... 182
Headlamps on Reminder........................... 182
Daytime Running Lamps (DRL)/
Automatic Headlamp System.................. 182
Instrument Panel Brightness...................... 183
Interior Lamps Control............................... 184
Dome Lamp.............................................. 184
Entry Lighting............................................ 184
Delayed Lighting........................................ 185
Exit Lighting.............................................. 185
Front Reading Lamps................................ 186Rear Reading Lamps................................ 186
Cargo Lamp.............................................. 186
Electric Power Management...................... 186
Battery Run-Down Protection..................... 187
Overhead Console Switchbank.................. 188
Ultrasonic Rear Parking
Assist (URPA)........................................ 188
Accessory Power Outlet(s)........................ 191
Power Outlet 115 Volt Alternating
Current.................................................. 192
Cigarette Lighter........................................ 193
Climate Controls......................................... 193
Climate Control System............................. 193
Dual Climate Control System..................... 197
Outlet Adjustment...................................... 200
Rear Climate Control System
(Option A, Uplevel)................................ 200
Rear Climate Control System
(Option B, Uplevel)................................ 203
Passenger Compartment Air Filter............. 205
Warning Lights, Gages, and Indicators..... 207
Instrument Panel Cluster........................... 208
Speedometer and Odometer...................... 209
Trip Odometer........................................... 209
Section 3 Instrument Panel
167