2007 BUICK RANDEZVOUS lock

The main components of the instrument panel are the following:
A. Exterior/Interior Lamps Control. SeeExterior
Lamps on page 185andInterior Lamps
on page 188.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 177.
C. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 176.
D. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 212.
E. Shift Lever. SeeAutomatic Transaxle Operation
on page 132.
F. Instrument Panel Outlets. SeeOutlet
Adjustment on page 210.
G. Audio System. SeeAudio System(s) on
page 250.
H. Audio Steering Wheel Controls. SeeAudio
Steering Wheel Controls on page 296.
I. Head-Up Display Switch and Driver Information
Center (DIC) Controls (If Equipped). See
Head-Up Display (HUD) on page 193andDIC
Controls and Displays on page 236.J. Hood Release. SeeHood Release on
page 363.
K. Ignition Switch. SeeIgnition Positions on
page 128.
L. Climate Controls. SeeClimate Control System
on page 200,Dual Climate Control System
on page 203orDual Automatic Climate Control
System on page 206.
M. Instrument Panel Switchbank. SeeInstrument
Panel Switchbank on page 192.
N. Front Armrest Storage. SeeFront Armrest
Storage Area on page 160.
O. Ashtray/Cigarette Lighter/Accessory Power
Outlet/Cell Phone Storage/Cupholders.
SeeAshtray(s) and Cigarette Lighter on
page 200,Accessory Power Outlet(s) on
page 199,Cell Phone Storage Area on
page 159,Floor Console Storage Area on
page 160andCupholder(s) on page 158.
P. Floor Console Fuse Block. SeeFloor Console
Fuse Block on page 463.
Q. Glove Box. SeeGlove Box on page 158.
175

Tilt Wheel
A tilt wheel lets you adjust the steering wheel
before you drive. You can raise the steering wheel
to the highest level to give your legs more room
when you enter and exit the vehicle.
The lever that lets you tilt the steering wheel is
located on the left side of the steering column.
To tilt the wheel, hold
the wheel and pull the
lever. Then move
the wheel to a
comfortable position and
release the lever to
lock the wheel in place.
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane-Change Signals. See
Turn and Lane-Change Signals on page 178.
53Headlamp High/Low-Beam Changer.
SeeHeadlamp High/Low-Beam Changer on
page 179.
Flash-to-Pass. SeeFlash-to-Pass on
page 179.
WIPERNWindshield Wipers. See
Windshield Wipers on page 179.
177

Windshield Washer
LPUSH:To wash your windshield, press and
hold the paddle with the windshield washer
symbol. The washers and wipers will operate.
When you release the paddle, the washers
will stop, and the wipers will continue to operate
for two cycles, unless your wipers were already on.
In that case, the wipers will resume the wiper
speed you selected earlier.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
Rear Window Wiper/Washer
The rear window
washer/wiper switch is
located in the
instrument panel
switchbank. See
Instrument Panel
Switchbank on
page 192.
Z(Rear Intermittent Wiper):Press the wiper
symbol on the top of the switch to turn on
the intermittent wiper. To turn off the wiper, gently
press the bottom of the switch.
180

=(Rear Wiper/Washer):To wash and wipe the
rear window, press the washer symbol on the
bottom of the switch. Washer uid will spray as
long as the switch is held in. When the switch
is released, the wiper will continue to cycle
three more times. There is only one washer uid
reservoir for the front and rear windshield
wipers. SeeWindshield Washer Fluid on page 388.
To wash the rear window while the rear wiper is
already on, press the bottom of the switch.
Press the top of the switch to continue the
intermittent wiper cycle after the washing cycle is
completed.
The rear window washer uses the same uid
bottle as the windshield washer. However, the rear
window washer will run out of uid before the
windshield washer. If you can wash your
windshield but not your rear window, check the
uid level.
Remember that a damaged wiper blade may
prevent you from seeing well enough to drive
safely. To avoid damage, carefully clear ice and
snow from the wiper blade before using it. If
it is frozen to the windshield, carefully loosen or
thaw the wiper blade. If your blade becomes
damaged, get a new blade or blade insert.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
Cruise Control
With cruise control, you can maintain a speed of
about 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This can
really help on long trips.
Cruise control does not work at speeds below
about 25 mph (40 km/h).
When you apply your brakes, the cruise control
disengages.
181

Headlamp Exit Delay
If your vehicle has headlamp exit delay, it will keep
the headlamps and parking lamps on at night for
30 seconds if the following conditions are met:
The ignition is turned to OFF.
The exterior lamp control is in the AUTO
position.
LOCK is pressed on the remote keyless entry
transmitter.
It is dark enough outside.
After 30 seconds, the headlamps and parking
lamps will turn off.
The lamps will turn off before the 30 seconds if
the following conditions are met:
The ignition is turned to ON.
The exterior lamp control is turned out of the
AUTO position.
If your vehicle is equipped with the Driver
Information Center (DIC), seeDIC Vehicle
Personalization on page 240to program the
headlamp exit delay feature.
Entry Lighting
If your vehicle has entry lighting, the interior of
your vehicle will illuminate for 25 seconds so you
can see inside your vehicle before you enter.
To activate entry lighting, do one of the following:
Unlock a door using the key when the
interior lamp control is in the DOOR position,
and when the ignition is in OFF.
Press UNLOCK on the remote keyless entry
transmitter when the interior lamp control is
in the DOOR position, and when the ignition is
in OFF.
After 25 seconds, the interior lamps will fade out.
The lamps will turn off before 25 seconds if
you do one of the following:
Press LOCK on the remote keyless entry
transmitter.
Press the front of the power door lock switch.
Turn the ignition to ON.
When any door is opened, entry lighting is
cancelled. The interior lamps will stay on while
any door or the liftgate is open, and fade out when
all the doors are closed.
189

Delayed Lighting
If your vehicle has delayed lighting, it will continue
to illuminate the interior for 25 seconds after all
doors have been closed. The lamps will continue to
illuminate when the following conditions are met:
A door is opened then closed.
The interior lamp control is in the DOOR
position.
The ignition is in OFF.
After 25 seconds, the interior lamps will fade out.
The lamps will fade out before the 25 seconds
if you do one of the following:
Turn the ignition to ON.
Press LOCK on the remote keyless entry
transmitter.
Press the front of the power door lock switch.
If your vehicle has with the Driver Information
Center (DIC), you can program this feature on or
off. SeeDIC Vehicle Personalization on
page 240.
Exit Lighting
If your vehicle has exit lighting, the interior lamps
will come on for about 30 seconds whenever
you remove the key from the ignition if the
following conditions are met:
The vehicle is in PARK (P).
The key is out of the ignition.
The interior lamp control is in the DOOR
position.
All of the doors are closed.
After 30 seconds, the interior lamps will fade out.
The interior lamps will fade out before 30 seconds
if you do one of the following:
Turn the ignition to ON.
Press LOCK on the remote keyless entry
transmitter.
Press the front of the power door lock switch.
If your vehicle has the Driver Information
Center (DIC), you can program this feature on or
off. SeeDIC Vehicle Personalization on
page 240.
190

Perimeter Lighting
If your vehicle has perimeter lighting, it will turn on
the headlamps and parking lamps for 25 seconds
when the following conditions are met:
The ignition is turned to OFF.
The exterior lamp control is in the AUTO
position.
UNLOCK is pressed on the remote keyless
entry transmitter.
It is dark enough outside.
After 25 seconds, the headlamps and parking
lamps will turn off.
The lamps will turn off before the 25 seconds if
you do one of the following:
Turn the ignition to ON.
Turn the exterior lamp control out of the
AUTO position.
If your vehicle has the Driver Information Center
(DIC), you can program this feature on or off. See
“Lock Feedback” underDIC Vehicle
Personalization on page 240.
Front Reading Lamps
There are two reading lamps located on the
rearview mirror.
To turn either reading lamp on or off, press the
button located next to each lamp. These lamps will
come on each time you open the doors, if the
interior lamp control is in the ON or DOOR
position.
Rear Reading Lamps
There are two reading lamps with coat hooks
above the rear doors.
To turn on or off either reading lamp, press the
lens of the lamp.
191

To adjust the HUD so you can see it properly, do
the following:
1. Start your engine and turn the dimmer knob to
the desired HUD image brightness.
The brightness of the HUD image is determined
by the ambient light conditions in the direction
your vehicle is facing and where you have the
HUD dimmer knob set. If you are facing a dark
object or a heavily shaded area, your HUD may
anticipate that you are entering a dark area and
may begin to dim.
2. Adjust the driver’s seat. If you change your
seat position, you may have to readjust
your HUD.3. Press the UP or DN buttons until the HUD
image is easy to see and then press the DN
button until the HUD image is as low as
possible, but remains in full view straight
ahead near the front bumper.
The HUD image can only be adjusted up and
down, not side-to-side.
4. To turn the image off, turn the dimmer knob
counterclockwise until it stops.
If the sun comes out or it becomes cloudy, you
may need to adjust the HUD brightness again
using the dimmer knob. Polarized sunglasses
could make the HUD image harder to see.
When you rst start the vehicle the display will
show BUICK and the Buick logo for a few seconds.
If it is cold outside, this display may stay on for
up to a minute.
Clean the inside of the windshield as needed to
remove any dirt or lm that reduces the sharpness
or clarity of the HUD image.
195