2007 BUICK RANDEZVOUS lock

Folding or Reclining the Seatbacks
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
To recline the seatback, lift the recliner lever
located on the outboard side of the seatback.
Release the lever when the seatback is in
the desired position.
22

Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
To fold the seatback forward, lift the recliner lever,
located on the outboard side of the seatback,
fully without applying pressure to the seatback.
To return the seatback to the upright position, lift
the recliner lever and move the seatback until
it locks in the upright position, Push and pull on the
seatback to make sure it locked in place.Removing the Captain Chairs
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
1. Lift the seatback recliner lever to fold
the seatback forward.
2. Pull the nylon strap behind the chair to
release the rear hooks from the oor pins.
23

3. Push the rear of the seat down to lock the
rear latches onto the rear set of oor pins.
{CAUTION:
A seat that is not locked into place
properly can move around in a collision or
sudden stop. People in the vehicle could
be injured. Be sure to lock the seat into
place properly when installing it.4. Push and pull on the seat to check that it is
properly attached.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
5. Return the seatback to the upright position.
Stowable Seat
The stowable seat is a two passenger bench seat
that comes with the rear convenience center.
SeeRear Convenience Center on page 165. The
stowable seat can be removed or, with the
seatback folded, lie at with the convenience
center.
26

Folding the Seatback
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
To fold the seatback
forward, lift the lever
located on the back of
the seat. Push the
seatback down until it is
locked into place.
Push and pull on the seatback to make sure that it
is locked into place.To raise the seatback, do one of the following:From the rear of the vehicle, lift the lever
to release the seatback. Then pull the
strap, located on the right side of the seat, to
lift the seatback up. The seatback has a
pocket on the side to stow the strap.
From the passenger’s side door, lift the lever
to release the seatback. Lift the seatback
and push it until it locks in place.
Push and pull on the seatback to make sure that it
is locked into place.
27

The stowable seat has seat position labels,
located on the back of the seat, showing where
the seat must go. The seat must be placed in the
proper location for the legs to attach correctly.
Notice:Folding a rear seat with the safety
belts still fastened may cause damage to the
seat or the safety belts. Always unbuckle
the safety belts and return them to their normal
stowed position before folding a rear seat.
1. Make sure that the seatback is folded forward
before beginning this procedure. See “Folding
the Seatback” previously.
2. Remove the nuts from the screws.
3. Place the stowable seat on the vehicle oor
so that the seat brackets are placed over the
screws.
4. Reinstall the nuts onto the screws. Torque to
approximately 18 lb ft (25
Y).
{CAUTION:
A seat that is not locked into place
properly can move around in a collision or
sudden stop. People in the vehicle could
be injured. Be sure to lock the seat into
place properly when installing it.
5. Try to raise the seat to make sure that it is
locked into place.
{CAUTION:
If the seatback is not locked, it could
move forward in a sudden stop or crash.
That could cause injury to the person
sitting there. Always push and pull on the
seatback to be sure it is locked.
6. Raise the seatback to its upright position.
Push and pull on the seatback to make
sure that it is locked into place.
29

Driver Position
Lap-Shoulder Belt
The driver has a lap-shoulder belt. Here is how to
wear it properly.
1. Close and lock the door.
2. Adjust the seat so you can sit up straight. To
see how, see “Seats” in the Index.
3. Pick up the latch plate and pull the belt across
you. Do not let it get twisted.
The lap-shoulder belt may lock if you pull the
belt across you very quickly. If this happens,
let the belt go back slightly to unlock it.
Then pull the belt across you more slowly.
36

The lap part of the belt should be worn low and
snug on the hips, just touching the thighs. In
a crash, this applies force to the strong pelvic
bones. And you would be less likely to slide under
the lap belt. If you slid under it, the belt would
apply force at your abdomen. This could cause
serious or even fatal injuries. The shoulder
belt should go over the shoulder and across the
chest. These parts of the body are best able
to take belt restraining forces.
The safety belt locks if there is a sudden stop or
crash.
38

To unlatch the belt, push the button on the buckle.
The belt should go back out of the way.
Before you close the door, be sure the belt is out
of the way. If you slam the door on it, you can
damage both the belt and your vehicle.
Shoulder Belt Height Adjustment
Before you begin to drive, move the shoulder belt
height adjuster to the height that is right for you.
Adjust the height so that the shoulder portion of
the belt is centered on your shoulder. The
belt should be away from your face and neck, but
not falling off your shoulder. Improper shoulder
belt height adjustment could reduce the
effectiveness of the safety belt in a crash.
To move it down, push
down on the button (A)
and move the height
adjuster to the desired
position. You can
move the height
adjuster up by pushing
up on the shoulder
belt guide.
After you move the height adjuster to where you
want it, try to move it down without pushing
the button down to make sure it has locked into
position.
45