2007 BUICK RAINIER garage door opener

5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for two
seconds and then turns to a constant light,
continue with Steps 6 through 8 following to
complete the programming of a rolling-code
device, most commonly, a garage door opener.
6. Locate in the garage, the garage door opener
receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be
found where the hanging antenna wire is
attached to the motor-head unit.7. Firmly press and release the “Learn” or
“Smart” button. The name and color of
the button may vary by manufacturer.
You will have 30 seconds to start Step 8.
8. Return to the vehicle. Firmly press and hold
the programmed Universal Home Remote
button for two seconds, then release. Repeat
the press/hold/release sequence a second
time, and depending on the brand of the
garage door opener or other rolling code
device, repeat this sequence a third time to
complete the programming.
The Universal Home Remote should now
activate the rolling-code device.
To program the remaining two Universal
Home Remote buttons, begin with Step 2 of
“Programming Universal Home Remote.” Do not
repeat Step 1, as this will erase all previous
programming from the Universal Home Remote
buttons.
142

Gate Operator and Canadian
Programming
Canadian radio-frequency laws require transmitter
signals to time out or quit after several seconds
of transmission. This may not be long enough
for Universal Home Remote to pick up the signal
during programming. Similarly, some U.S. gate
operators are manufactured to time out in
the same manner.
If you live in Canada, or you are having difficulty
programming a gate operator or garage door
opener by using the “Programming Universal
Home Remote” procedures, regardless of where
you live, replace Step 3 under “Programming
Universal Home Remote” with the following:
Continue to press and hold the Universal Home
Remote button while you press and release every
two seconds (cycle) the hand-held transmitter
button until the frequency signal has been
successfully accepted by the Universal Home
Remote. The Universal Home Remote indicator
light will ash slowly at rst and then rapidly.
Proceed with Step 4 under “Programming
Universal Home Remote” to complete.
Using Universal Home Remote
Press and hold the appropriate Universal Home
Remote button for at least half of a second.
The indicator light will come on while the signal is
being transmitted.
Erasing Universal Home Remote
Buttons
To erase programming from the three Universal
Home Remote buttons do the following:
1. Press and hold down the two outside buttons
until the indicator light begins to ash, after
20 seconds. Do not hold the two outside
buttons for longer than 30 seconds.
2. Release both buttons.
The Universal Home Remote is now in the training
(learning) mode and can be programmed at any
time beginning with Step 2 under “Programming
Universal Home Remote” shown earlier in
this section.
Individual buttons cannot be erased, but they
can be reprogrammed. See “Reprogramming a
Single Universal Home Remote Button” following
this section.
143

F
Filter
Engine Air Cleaner................................... 374
Finish Damage............................................ 460
Fixed Mast Antenna.................................... 279
Flashers, Hazard Warning........................... 154
Flash-to-Pass.............................................. 157
Flat Tire...................................................... 435
Flat Tire, Changing...................................... 436
Flat Tire, Storing......................................... 450
Fluid
Automatic Transmission............................ 375
Power Steering........................................ 390
Windshield Washer.................................. 391
Fog Lamps.................................................. 165
Front Axle................................................... 403
Fuel............................................................ 358
Additives.................................................. 359
California Fuel.......................................... 359
Check Gas Cap Light.............................. 197
Filling a Portable Fuel Container.............. 363
Filling Your Tank...................................... 361
Fuels in Foreign Countries....................... 360
Gage....................................................... 197
Gasoline Octane...................................... 358Fuel (cont.)
Gasoline Specications............................ 358
Low Warning Light................................... 197
Fuses
Engine Compartment Fuse Block............. 465
Fuses and Circuit Breakers...................... 465
Rear Underseat Fuse Block..................... 471
Windshield Wiper..................................... 464
G
Gage
Check Gages Warning Light..................... 196
Engine Coolant Temperature.................... 189
Fuel......................................................... 197
Oil Pressure............................................. 193
Speedometer........................................... 179
Tachometer.............................................. 179
Voltmeter Gage........................................ 185
Garage Door Opener..........................133, 134
Gasoline
Octane..................................................... 358
Specications........................................... 358
Gate Ajar Light............................................ 196
Glove Box................................................... 144
GM Mobility Reimbursement Program.......... 503
524