2007 BUICK LACROSSE bulb

RIGHT REAR TURN LAMP OUT
This message displays when the right rear turn
signal bulb needs to be replaced. SeeTaillamps,
Turn Signal, Sidemarker, Stoplamps and
Back-up Lamps on page 398.
This message displays while the ignition is in RUN.
Press any of the DIC buttons to acknowledge this
message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
SERVICE ABS SYSTEM
If the vehicle has the Anti-lock Brake System (ABS),
this message displays when the system is not
functioning properly. Have the brake system
serviced by your dealer as soon as possible.
The anti-lock brake system warning light also
appears on the instrument panel cluster when this
message appears on the DIC. SeeAnti-Lock
Brake System Warning Light on page 187.
This message only displays while the ignition is in
RUN. Press any of the DIC buttons to acknowledge
this message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine is
turned off. It also re-displays for two seconds if the
message has been acknowledged, but the
condition still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
222

Following Distance
Stay at least twice as far behind the vehicle ahead
as when driving the vehicle without a trailer.
This can help avoid situations that require heavy
braking and sudden turns.
Passing
More passing distance is needed up ahead when
towing a trailer. And, because the vehicle is a
good deal longer with the trailer, you will need to
go much farther beyond the vehicle you have
passed before you can return to the proper lane.
Backing Up
Hold the bottom of the steering wheel with one
hand. Then, to move the trailer to the left,
move that hand to the left. To move the trailer to
the right, move your hand to the right. Always
back up slowly and, if possible, have someone
guide you.
Making Turns
Notice:Making very sharp turns while
trailering could cause the trailer to come in
contact with the vehicle. Your vehicle could be
damaged. Avoid making very sharp turns while
trailering.
When turning with a trailer, make wider turns than
normal. Do this so the trailer will not strike soft
shoulders, curbs, road signs, trees, or other
objects. Avoid jerky or sudden maneuvers. Signal
well in advance.
Turn Signals When Towing a Trailer
When towing a trailer, the vehicle may need a
different turn signal asher and/or extra wiring.
Check with your dealer. The arrows on the
instrument panel will ash whenever signaling a
turn or lane change. Properly hooked up, the trailer
lamps will also ash, telling other drivers you are
about to turn, change lanes or stop.
When towing a trailer, the arrows on the instrument
panel will ash for turns even if the bulbs on the
trailer are burned out. You may think drivers behind
you are seeing your signal when they are not. It is
important to check occasionally to be sure the
trailer bulbs are still working.
333

Service........................................................ 340
Accessories and Modications................... 341
California Proposition 65 Warning.............. 341
Doing Your Own Service Work.................. 342
Adding Equipment to the Outside
of Your Vehicle...................................... 343
Fuel............................................................. 343
Gasoline Octane........................................ 343
Gasoline Specications.............................. 344
California Fuel........................................... 344
Additives................................................... 344
Fuels in Foreign Countries........................ 345
Filling the Tank......................................... 346
Filling a Portable Fuel Container............... 348
Checking Things Under the Hood.............. 348
Hood Release........................................... 349
Engine Compartment Overview.................. 350
Engine Oil................................................. 353
Engine Oil Life System.............................. 356
Engine Air Cleaner/Filter............................ 358
Automatic Transaxle Fluid......................... 360Engine Coolant.......................................... 363
Radiator Pressure Cap.............................. 367
Engine Overheating................................... 367
Overheated Engine Protection
Operating Mode..................................... 370
Cooling System......................................... 370
Power Steering Fluid ................................. 378
Windshield Washer Fluid........................... 380
Brakes...................................................... 381
Battery...................................................... 384
Jump Starting............................................ 385
Headlamp Aiming........................................ 391
Bulb Replacement....................................... 394
Halogen Bulbs........................................... 394
Headlamps and Sidemarker Lamps........... 395
Front Turn Signal and Parking Lamps....... 397
Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps.............. 398
License Plate Lamp................................... 400
Replacement Bulbs................................... 400
Windshield Replacement............................ 401
Section 5 Service and Appearance Care
337

9. Make sure that the light from the headlamp is
positioned at the bottom edge of the horizontal
tape line. The lamp on the left (A) shows
the correct headlamp aim. The lamp on the
right (B) shows the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for the opposite
headlamp.
Bulb Replacement
For the proper type of replacement bulbs, see
Replacement Bulbs on page 400.
For any bulb changing procedure not listed in
this section, contact your dealer.
Halogen Bulbs
{CAUTION:
Halogen bulbs have pressurized gas
inside and can burst if you drop or
scratch the bulb. You or others could be
injured. Be sure to read and follow the
instructions on the bulb package.
394

Headlamps and Sidemarker Lamps
A. Sidemarker Lamp
B. Low-Beam Headlamp
C. High-Beam Headlamp
Low-Beam Headlamp and
Sidemarker Bulbs
To replace a low-beam headlamp or sidemarker
bulb, do the following:
1. Open the hood. SeeHood Release on
page 349for more information.
2. Remove the fastener from the front fascia.
The fastener is located inboard of the
headlamp assembly, near the high-beam
headlamp.
395

3. Pull up on the plastic retaining clip (C) while
pushing rearward on the headlamp. Align the
square cut-out on the retaining clip with
the notch on the headlamp.
4. Remove the screw (A) from the metal
headlamp retainer to pull up and release the
headlamp assembly.
5. Remove the push pin (B) retaining the front
fascia.6. Pull forward on the front fascia and then pull
the headlamp assembly out from the vehicle.
Moving the headlamp up and down slightly
may help with its removal.
You may have someone assist you with
this step.
7. Remove the access cover from behind the
bulb being replaced.
8. Turn the bulb socket one-quarter of a turn to
remove it from the headlamp assembly.
9. Holding the base of the socket, pull the old
bulb from the socket.
10. Replace with a new bulb.
11. Reverse all the steps to reassemble the
headlamp assembly.
When replacing the plastic retaining clip,
push down on it while pushing rearward on
the headlamp, making sure the headlamp
assembly is secure.
396

High-Beam Headlamp Bulbs
To replace the high-beam headlamp bulb, do the
following:
1. Open the hood. SeeHood Release on
page 349for more information.
2. Locate the high-beam headlamp bulb socket.
3. Remove the access cover from behind the
bulb being replaced.
4. Turn the bulb socket counterclockwise and
pull it from the headlamp assembly.
5. Holding the base of the socket, pull the old
bulb from the socket.
6. Replace with a new bulb.
7. Reverse Steps 2 through 4 to reinstall.
Front Turn Signal and Parking
Lamps
To replace a front turn signal/parking lamp bulb in
the front fascia, do the following:
1. Locate the front turn signal/parking bulb
socket by reaching behind the front bumper.
2. Turn the bulb socket counterclockwise and
pull it out of the assembly.
3. Holding the base of the socket, pull the old
bulb from the socket.
4. Push the new bulb into the socket.
5. Reverse Steps 1 through 3 to reinstall.
397

Taillamps, Turn Signal, Sidemarker,
Stoplamps and Back-up Lamps
To replace a taillamp, turn signal, sidemarker,
stoplamp or back-up lamp bulb, do the following:
1. Open the trunk. SeeTrunk on page 100
for more information.
2. Remove the convenience net if the vehicle
has one.
3. Remove the four plastic wing nuts retaining
the trunk trim. There are two wing nuts
located on the driver’s side (shown) and
two located on the passenger’s side of the
vehicle.
4. Pull back the trunk trim.
398