2007 BMW 7 SERIES sensor

Maintenance Program
The BMW Maintenance Program has been
devised with the following objectives: to maxi-
mize vehicle safety, reliability, and resale value by
minimizing breakdowns resulting from wear, and
minimizing cost and inconvenience by comput-
ing maintenance intervals based upon the spe-
cific manner in which each individual vehicle is
driven.
Maintenance intervals on motor vehicles have
conventionally been specified based upon accu-
mulated mileage. However, driving conditions
have a major influence on routine maintenance
requirements; distance traveled is only one of the
significant factors. A vehicle driven for 50,000
miles of short trips in the city with numerous cold
starts, prolonged periods of idling, stop-and-go
driving, and high engine speeds during accelera-
tion requires more frequent maintenance inter-
vals than a vehicle driven for 50,000 miles for
long distances at low engine speeds primarily at
operating temperature.
The advanced technologies at BMW have led to
the development of the unique BMW Condition
Based Service (CBS) system which computes
the actual optimum maintenance requirements
based not only upon the accumulated mileage,
but taking into account important factors such as
high or low engine speeds, short or long trip driv-
ing, and condition of the engine oil and brake
pads.
The BMW Maintenance Program
Condition Based Service (CBS)
CBS is a further development of the Service
Interval Indicator System. Sensors and sophisti-
cated algorithms take even more detailed
account of the various conditions of vehicle use.The remaining times for selected maintenance
tasks as well as any legally prescribed dates are
displayed to you individually:
Engine oil
Brakes - front and rear separately
Microfilter
Brake fluid
Spark plugs
Vehicle check
Required State Inspection(s)
CBS thus determines the current and future
maintenance requirements. This data can also be
read from the vehicle key by your BMW Service
Advisor and used to propose the optimum scope
of maintenance.
Have maintenance and repair work performed by
your BMW center. Make sure that the mainte-
nance work is stamped in this Service and War-
ranty Information Statement. These entries are
the evidence of regular maintenance of your vehi-
cle and a requirement for warranty claims.
Disconnecting the battery during periods
of long-term storage will interrupt the
calculation of time-based services. Have all items
requiring time-based maintenance, such as
brake fluid and coolant, and possibly also the
engine oil and microfilter, brought up to date by
your BMW center. Also see the section on bat-
tery care on page 15 of this statement.
Service Interval Display
Info Display screen contents
The distance remaining until your next service
briefly appears when you switch on the ignition.
2

BMW is evaluating various synthetic oils for
inclusion in our list of recommended engine oils.
For the most current list of synthetic oils, please
contact your BMW center, or call BMW of North
America, LLC. at 1 800 831-1117. You can also
obtain this information from our website,
www.bmwusa.com/.
BMW recommends that you check your engine
oil level whenever you add fuel to your vehicle. If
you need to add oil between oil changes and are
unable to obtain BMW High Performance Syn-
thetic Oil, Mobil 1 or another special oil on the
list, use a synthetic oil with an API rating of SH or
higher.
The following maintenance elements must be
performed at the mileage/time stated (time inter-
vals begin from the vehicles production date):
– Brake Fluid Service: Change brake fluid every
two years, or when specified by CBS.
– Oxygen Sensor Service: The oxygen sensor
deteriorates strictly on a mileage basis and
must therefore be replaced at the following
intervals to maximize vehicle fuel economy and
minimize exhaust pollution.
750i, 750Li: 120,000 miles.
760Li: 100,000 miles.
– Spark Plug Service: Replace at 100,000 miles,
or when specified by CBS.
– The engine coolant has a lifetime rating and
does not need to be changed.
For your convenience, you may also wish to have
your BMW center perform any necessary opera-
tions to fulfill any state inspection requirements
in your area concurrent with the maintenance
elements specified above during other repairs.
Make sure that confirmation of maintenance
work is always entered in this Service and War-
ranty Information Statement. You may need this
for any warranty claims that become necessary,
and later on as evidence that your car has been
given the correct and regular maintenance that
justifies its resale or trade-in value.
BMW has applied the most modern technologi-
cal advances not only to the design and produc-
tion of your vehicle, but also to computing of the
optimum maintenance interval for your type of
operations and driving style. Your BMW centerhas made a substantial investment in unique
BMW special service tools to enable his BMW
factory trained service technicians to perform
quality repairs on your BMW in minimal time.
Your service technician looks forward to serving
your every service need and to help maximize
your satisfaction with your BMW, its longevity,
and resale value.
Quality Certification I
For a detailed list of items inspected, refer to the
Quality Certification I form provided to the Owner
at time of delivery. A copy of the form is on file at
the selling BMW center.
Special Note
The maintenance requirements for your vehicle
are determined dynamically by the Condition
Based Service (CBS) system . The maintenance
items stated herein reflect the latest information
available at the time of the printing of this state-
ment, and are subject to change. The most cur-
rent maintenance recommendations are available
from your authorized BMW center.
Maintenance summary
The Condition Based Service (CBS) system will
determine the requirement for performance of
the maintenance services described on this and
the following page. These services may be
required either individually or in conjunction with
other maintenance services.
4

Emission Control Maintenance
Schedule
The maintenance schedule as shown is required
for the proper functioning of the emission control
systems for optimum vehicle performance and
fuel economy.
Basic Engine
Engine oil As specified by CBS
Engine oil filter As specified by CBS
Fuel System
Air filter As specified by CBS
Ignition System
Spark plugs As specified by CBS
Emission Control
Components
Oxygen sensor Replace at intervals of
750i, 750Li: 120,000 miles
760Li: 100,000 miles
Oxygen Sensor Service: The oxygen sensor
deteriorates strictly on a mileage basis and must
therefore be replaced to maximize vehicle fuel
economy and minimize exhaust pollution.
Battery Care
If your car is driven only for short distances of
less than 10 miles over a prolonged period of
time, without an occasional drive at highway
speeds, the engines charging system will not
maintain the battery. Insufficient use of the vehi-
cle could result in short term starting problems
and in the long term could damage the battery.
In case the car is not operated for several weeks
it is advisable to:
a. slide battery switch to Off position. Refer to
Battery Switch in vehicle owners manual.
b. consider using a proper trickle charger, follow-
ing the charger manufacturers instructions, to
maintain the batterys state of charge; or
c. consult your BMW center regarding battery
removal. Once removed, the battery must be
charged and stored in a cool, dry place where
it can be protected from freezing. If the battery
will be stored for over 3 months, it must berecharged every 3 months, or else it will
become damaged and useless.
Please consult with your BMW center for further
guidance and information.
Corrosion Protection
Extensive corrosion protection measures imple-
mented by BMW now make it possible to offer a
twelve-year unlimited mileage anti-corrosion
warranty against rust perforation on your vehicle
provided that the vehicle is maintained in accor-
dance with the provisions of the New Vehicle
Limited Warranty as outlined in the Warranty
Section of this Booklet (page 31).
The major degree of corrosion protection is due
to the electrophoretic dip painting process which
cathodically deposits paint particles on all body
parts, attracting paint particles into the minutest
cavities or seams. Body parts are designed to
provide optimum corrosion protection.
During manufacture, exterior body parts receive
an additional corrosion protection coat. Hood,
trunk, doors and other body parts are coated with
PVC and sealed from the outside.
All floor panels receive a resilient coating of PVC
for maximum protection against damage due to
stones, etc.
Corrosion protection materials tested over many
years are applied to the surfaces of cavities and
to the entire underside of the vehicle during and
after assembly.
Requirements for maintaining the 12- year unlim-
ited mileage anti-corrosion warranty are outlined
in the Warranty Section of this Booklet (page 33).
Restoring corrosion protection
Please take care that anti-corrosion material is
replaced when your car is repaired after body or
chassis damage.
BMW will not accept any liability for any parts
and accessories not approved by BMW.
15

nents within these systems apply to your vehicle,
please contact your BMW center.
AIR INDUCTION SYSTEM
FUEL METERING SYSTEM
IGNITION SYSTEM
POSITIVE CRANKCASE VENTILATION
SYSTEM (PCV)
FUEL EVAPORATIVE CONTROL SYSTEM
EXHAUST SYSTEM
ENGINE EMISSION CONTROL SYSTEM
SENSORS/DEVICES
ON BOARD DIAGNOSTIC SYSTEM (OBD)
RELATED PARTS ASSOCIATED WITH
THE ABOVE SYSTEMSThe following components and/or system are/is
covered under the Federal Emission Warranty for
a period of 8 years or 80,000 miles, whichever
occurs first.
CATALYTIC CONVERTER
ENGINE CONTROL MODULE (INCLUDING
ON-BOARD DIAGNOSTIC SYSTEM)
For assistance in determining coverage of the
specific components of the on-board diagnostic
system, please contact your BMW center.
37

California Emission Warranty Parts
List
The following components are covered for
defects by the California Emission Control Sys-
tem Limited Warranty for a period of 7 years or
70,000 miles, whichever comes first:
Component 750i
750Li760Li
Cylinder Head Cover
Gasket Set••
Engine Control Module••
Exhaust Manifold Gasket••
Exhaust Manifold
w/Catalyst••
Fuel Expansion Tank
w/Carbon Canister••
Fuel Tank••
Intake Manifold Gasket••
Intake Manifold System•
Knock Sensor••
Transmission Control Unit••
Torque Converter••
Valvetronic Control Unit••
Valvetroninc Actuator•
Valvetronic Eccentric
Shaft Sensor••
Vanos (VVT) Camshaft
Adjustment Unit••
Fuel Injector•
Fuel Injector O-Ring•
Fuel Pressure Sensor•
Fuel Rail•
High Pressure Fuel Pipe•
High Pressure Fuel Pump•
Tire Warranty Statement
Tires are warranted by their respective manufac-
turer as detailed in the applicable tire manufac-
turers warranty statements. Instructions for
proper tire care and maintenance are contained
in the Owners Manual. Should you experience
difficulty in obtaining warranty service from a tire
manufacturer, your authorized BMW center will
assist you in resolving the difficulty.
Notice
The National Traffic Motor Vehicle Safety Act of
1966 requires manufacturers to be in a position
to contact the vehicle owners when a correction
of a product defect becomes necessary. Please
fill in the attached postcard if you change your
address or purchase a used BMW.
41