2007 AUDI A3 Point

Navigation (NAV) 138
– Select Load route
page 134, fig.140.
– Select the route that you would like to load from the list.
– Select Start route guidance.After storing several route plans
page 137, they can be loaded
with a few operating steps.
A route plan can be changed at any time. Select a destination from
the route plan by rotating and pressing the control knob. Then you
can select Change, Move, Delete or Drive to now.
Change
Here you are entering new navigation data for your destination or
stopover.
Move
Here you are reordering the sequence of your destination and stop-
overs.
Delete
The selected destination or stopover can be deleted. If you delete a
destination, the system will automatically select a stopover and
make that your new destination.
Drive to now
You can drive directly to the selected final destination or stopover.
If you do not want to ed it the saved route, the route will b e sa ved in
the memory when Start route guidance is activated and the current
vehicle location will be used as the starting point for navigation.
Tips
A function may not be selected (“greyed-out”) if it is not available
according to the restrictions you have set, or if not permitted by
local circumstances.Delete route–Press the Memory control button in the navigation menu.
– Select Delete route.
– Select the route to be deleted from the list.
–Confirm Are you sure you want to delete the route? with
Ye s. The selected route is deleted.

Navigation (NAV)143
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP the map by light grey lines
f i g .1 4 9 . Th e r e i s n o r o u t e g u i d a n c e f o r
IPD sections, instead you are guided by directional arrows
fig.149. These directional arrows point in the compass direc-
tion/a direct line to the destination.
I f y o u s h o u l d b e s t a r t i n g y o u r r o u t e g u i d a n c e i n a n I P D a r e a , y o u w i l l
initially be guided by directional arrows. As soon as you leave the
IPD area, route guidance will start . In
page 142, fig.149 an
example is shown of a directional arrow in an IPD area.
If your destination should lie in an IPD area, the Navigation System
will guid e you up to the star t of the IPD area. In the IPD area you will
be guided by directional arrows.
If your route guidance includes an IPD area, you will be advised of
this by a voice message when route guidance starts (“It is possible
that there a re un fore seen tra ffic reg ulations on the way to the des ti-
nation.”).
Tips
Route guidance is additionally shown by directional arrows in the
instrument cluster display
page 113 or
page 114. In an IPD
area, the directional arrows in the instrument cluster display point
in the compass direction/a direct line to the destination.
Map and information displayFig. 150 Navigation: Example of map display with inactive side menu
Fig. 151 Navigation: Example of map display with activated turn list
A
A1

Navigation (NAV) 146
–Press the button
page 18, to leave the map
side menu.When you change the map orientation with the side menu active,
this map orientation remains only for the time the side menu is
active. After the map side menu is deactivated, the orientation
entered in Setup becomes active again
page 153.
When you make the selection North, the map is oriented to the
North
page 145, fig.153. The vehicle always remains in the center
of the display.
When you make the selection Drive, the vehicle symbol is oriented
pointing upward. The map rotates around the vehicle.
An active map side menu is deactivated again by pressing the
button
page 144.
Zoom mapFig. 154 Navigation: Adjusting zoom with inactive side menu
Fig. 155 Navigation: Adjusting zoom in active side menu
RETURN
RETURN

Navigation (NAV)147
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Changing scale with inactive side menu:
–Press the Map control button in the navigation menu.
– Rotate the control knob counterclockwise to zoom into
the map (smaller scale, display of details), or
– Rotate the control knob clockwise, to zoom out of the
map (larger scale, more overview). You are shown the
scale
page 146, fig.154 in the side menu.
Changing scale with inactive side menu:
–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu.
– Rotate the control knob to the second menu item.
– Press the control knob to activate the map menu item
Zoom (white highlight)
page 146, fig.155.
– Rotate the control knob counterclockwise to zoom into
the map (smaller scale, display of details), or
– Rotate the control knob clockwise, to zoom out of the
map (larger scale, more overview). You are shown the
scale
page 146, fig.155 in the side menu.
–Press the button
page 18, to leave the map
side menu.The scale can be set from 50 m to 600 km.
When you change the scale with the side menu active, this change
in scale remains only for the time the side menu is active.By pressing the button once, you leave Zoom mode and
you can use other map menu items. Pressing the button
again deactivates the active side menu.
The scales recommended for driving are:


on freeways 3.5 km


on secondary roads 750 m


in cities 200 mTips
If you have activated automatic intersection zoom
page 159, the
map display automatically changes the scale to intersections or
turn points.
A1
A
A
RETURN
RETURN
RETURN

Navigation (NAV) 148Map position menuFig. 156 Navigation: Map position
Fig. 157 Navigation: Map position menu
–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu.
– Rotate the control knob to the third menu item

fig.156.
– Press the control knob.
– Select Detail info, Set as destination, Set as stopover or
Save to directory.You can set the point marked at the time by the crosshairs as a desti-
nation or stopover, or save it to the directory. If additional detailed
information is available for the selected point on the map, you can
display it using the Detail info function.
You can also specify a new point on the map by moving the
crosshairs
page 149. This new point can then be Set as
destination, Set as stopover or you can Save in directory.
You can use the Set as stopover f u n c t i o n i f y o u h a v e e n t e r e d “ R o u t e
with stopovers” page 139.

Navigation (NAV)149
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Move map
A new destination or stopover can be set using the
map by moving the crosshairs horizontally and verti-
cally.Fig. 158 Navigation: Moving the crosshairs horizontallyFig. 159 Navigation: Moving the crosshairs vertically
–Press the Map control button in the navigation menu.
– Press the control knob to switch to the side menu.
– Rotate the control knob to the fourth menu item.
– Press the control knob, the horizontal line in the
crosshairs is highlighted in white
fig.158.
– Rotate the control knob to the desired point.
– Press the control knob, the ver tical line in the crosshairs
is highlighted in white
fig.159.
– By pressing the control knob you can switch back and
forth between horizontal and vertical movement.If the crosshairs remain in a new position, detailed information
(street or city name) is displayed for the current position .

Navigation (NAV)153
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP night
The map display contains all topographical details. The background
is shown dark
page 152, fig.164. This provides a glare-free view
o f t h e m a p . T h e s t r e e t n a m e s a n d t h e i r l a y o u t , p l a c e n a m e s a n d m a p
contents are in contrasting light colors
auto
The map scheme changes automatically from day to night display
when the low-beam lights are turned on.
Map orientationFig. 165 Setup Navigation: Map orientation North– Press the function button
page 16 in the navi-
gation menu.
–Select Orientation.– Select north, dir. of travel or auto.
north
The map display is always oriented north, the directional arrow on
the vehicle symbol rotates accordingly
fig.165.
dir. of travel
The vehicle symbol points to the top. The map rotates accordingly
when vehicle direction changes.
auto
The map is oriented automatically depending on the selected scale.
Less than 1.5 miles oriented to dir. of travel and greater than 1.5
miles oriented to north.
SETUP

Navigation (NAV)159
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
– Press the function button
page 16 in the navi-
gation menu.
– Highlight the Intersection map with a check mark



page 158, fig.171 to activate the function.
The map is divided into two parts at intersections. The right half of
the display continues to show you the map display you selected.
Th e l e ft h a l f o f t he d i s p l a y s h o w s y o u a p a ra l l e l e n l a r g e d v i e w o f t h e
intersection area
page 158, fig.172.
Next to the enlarged view, you are shown the changes in distance
until the turn-off point. At the same you are shown the name of the
street onto which you want to turn.
If you have activated the Auto intersection zoom function, the
Intersection map function cannot be activated.
If you would like to activate the Intersection map function, you first
have to deactivate the Auto intersection zoom function. These two
functions are mutually exclusive.
Tips
The map is oriented to driving direction
page 153 when switching
to zoom mode.
Auto intersection zoom
The map displays in zoom mode at intersections.Fig. 173 Setup Navigation: Auto intersection zoom activated– Press the function button
page 16 in the navi-
gation menu.
– Highlight the Auto intersection zoom with a check mark


fig.173 to activate the function.
For a detailed display, the map automatically zooms in at street
intersections, enhancing the view of the route from street to street.
If you have activated the Itersection map function, the Auto
intersection zoom function cannot be activated.
If you would like to activate the Auto intersection zoom function,
you first have to deactivate the Intersection map function. These
two functions are mutually exclusive.
SETUP
SETUP