2007 Alfa Romeo 156 recommended oil

GETTING TO KNOW YOUR CAR45
The bags inflate instantaneously, setting
themselves between the body of the front
passengers and the car door. The bags de-
flate immediately afterwards.
In the event of minor side crashes (for
which the restraining action of the seat belts
is sufficient), the air bags are not deployed.
Also in this case it is of vital importance to
wear the seat belts since in case of side
crash they guarantee proper positioning of
the occupant and prevent the occupant to
be pitched out of the car in case of violent
crashes.
Therefore the side air bags do not replace
but are complementary to the use of belts,
which you are recommended to always
wear, as specified by law in Europe and most
non-European countries.
Operation of the side air bags and window
bags is not disabled by the front air bag de-
activation switch, as described in the previ-
ous paragraphs.WARNINGThe front and/or side air
bags may be activated if the car is subjected
to heavy shocks or accidents that involve the
underbody area, such as for example violent
bumps against steps, pavements or fixed ob-
stacles on the ground, falling into big holes
or bumpy roads.WARNINGThe triggering of air bags re-
leases a small amount of powder. This pow-
der is not harmful and does not indicate a
start of fire; also the surfaces of the de-
ployed bag and the car interior may be cov-
ered with dusty residue: this may irritate the
skin and eyes. In the event of exposure,
wash with neutral soap and water. WARNINGIn the event of side crash,
you can obtain the best protection by the
system keeping a correct position on the
seat, thus allowing correct window bag un-
folding.
The airbag system has a validity of 14
years for the pyrotechnic charge and 10
years for the coil contact (see the plate lo-
cated on the front left door near the lock).
Contact Alfa Romeo Authorized Services
for replacement as these dates approach.
Never rest head, arms and
elbows on the door, on the
windows and in the window bag
area to prevent possible injuries
during the inflation phase.
WARNING
Never lean head, arms and
elbows out of the window.
WARNING

GETTING TO KNOW YOUR CAR
179
If the
x
low brake fluid
warning light comes on (to-
gether with the message + symbol
shown by the display), stop the car
immediately and contact the near-
est Alfa Romeo Authorized Ser-
vices. Indeed, any leak of fluid
from the hydraulic system com-
promises the effectiveness of both
the conventional brake system and
the system with antilock system.
WARNING
The turning on of the
>
warning light (together
with the message + symbol shown
by the display) with the engine
running normally indicates an ABS
system fault. In this case the brak-
ing system preserves its effec-
tiveness, without however making
use of the antilock device. Under
these circumstances, the EBD sys-
tem may fail to give top perfor-
mance. In this case, too, you are
recommended to contact Alfa
Romeo Authorized Services imme-
diately, driving in such a way as to
avoid abrupt braking, to have the
system checked.
WARNING
VDC AND ASR
SYSTEMS(where required)VDC SYSTEM (VEHICLE
DYNAMICS CONTROL):
GENERALThe VDC is an electronic vehicle stability
control system which, acting on the torque
and braking the wheels in a differentiated
manner, helps to bring the car back to the
correct course in the event of loss of grip.
While travelling the car is subjected to lat-
eral and longitudinal forces that may be
controlled by the driver up to when the
tyres offer adequate road-holding; when
this falls below the minimum level, the car
starts to deviate from the course required
by the driver.
Above all on rough surfaces (such as cob-
bles, or due to the presence of water, ice
or soil), changes in speed (when accelerat-
ing or braking) and/or course (bends or the
need to avoid obstacles) can cause the tyres
to lose grip.When the sensors detect the conditions
that would lead to skidding, the VDC system
acts on the engine and brakes generating
a stabilising torque.
The system performance
levels, in terms of active
safety, should not induce the dri-
ver to run pointless and unjustified
risks. Driving conduct should al-
ways be suited to the conditions of
the road surface, vision and traf-
fic. The responsibility for road
safety is always and anyway the
vehicle driver’s concern.
The VDC system helps the driver
to keep control of the car in the
event of loss of tyre grip.
The forces induced by the VDC sys-
tem to control the lack of stability
of the car always and anyway de-
pend on the grip between the tyre
and the road surface.
WARNING

Fuel oil heater (JTD versions, JTD 16V Multijet)Services switched off with startingBattery power supply for Alfa Romeo CODE/Injection system(+15) key-controlled service supply (ignition switch)General service supply (petrol versions)General service supply (diesel versions)General service supplyAdditional heater (diesel version only)Oil pump supply (Selespeed versions only)
Selespeed gearbox(2.0 JTS version)
Automatic gearbox(2.5 V6 24V version)(*) Specific components and values depending on the version/market. If in doubt, especially for the replacement of fuses which protect safety circuits
and/or systems (Air bag, ABS, etc.), you are recommended to contact Alfa Romeo Authorized Services, also to locate the cause of the fuse tripping.
IN AN EMERGENCY
241
74
71
71
68
68
68
68
68
68
68
68
68
68 25A
7.5A
7.5A
30A
80A
80A
70A
70A
30A
30A
20A
40A
20A H
1
12
2
4
1
3
10
10
7
8
7
8
SERVICES FUSE AMPERES FIGURE

CAR MAINTENANCE
251
ADDITIONAL
OPERATIONSEvery 1000 kmor before long journeys
check and if necessary top up:
– engine coolant level
– brake fluid/hydraulic clutch control flu-
id level
– power steering fluid level
– windscreen washer and headlamp wash-
er fluid level
– tyre pressure and conditions.
Every 3000 kmcheck the level of the
engine oil and top up if necessary.
You are recommended to use products of
the FL Selenia, designed and developed
expressly for Alfa Romeo cars (see the table
“Specifications of fluids and lubricants” in
the “Technical specifications” chapter).
ANNUAL INSPECTION
PROGRAMMEAn annual inspection programme
has been established for cars thet
cover less than 20,000 km (e.g.
10,000 km). It consists of the fol-
lowing:
– Check tyre conditions/wear and adjust
pressure if required (including the compact
spare wheel)
– Check lighting system operation (head-
lights, direction indicators, hazard lights,
boot lights, passenger compartment lights,
glovebox light, warning lights of instrument
panel, etc.)
– Check windscreen and rear-screen
wiper/washer operation, adjust nozzles
– Check windscreen/rear-screen blade po-
sition/wear
– Check condition and wear of the front
brake pad
– Check for bonnet and boot lock clean-
ness, lever cleanness and lubrication– Visually check the following: engine,
gearbox, transmission, piping (exhaust - fu-
el - brakes) rubber components (casings -
sleeves - bushings, etc..), brake and fuel
hoses
– Check battery charge condition
– Visually check the condition of the belts
and various controls
– Check and top up if necessary, the flu-
id levels (coolant, brake fluid, windscreen
washer fluid, battery, etc.)
– Change engine oil
– Replace engine oil filter
– Change pollen filter.

CAR MAINTENANCE
273
Proceed as follows:
– Raise the windscreen wiper arm and po-
sition the blade so that it forms an angle
of 90° with the arm.
– Press tab (B) of the coupling spring and
remove the blade to be replaced from the
arm (A).
– When the spring is released from the
curved top of the arm, move the blade to al-
low the arm to be withdrawn through the slot.
– Insert a new blade passing it through the
curved top of the arm (A) through the slot.
– Lift the blade to clamp tab (B) of the cou-
pling spring with the curved top of the arm.
– Lower the windscreen wiper arm.
WARNINGThe blades may differ ac-
cording to the versions. In any case, follow
the instructions provided in the packs avail-
able as spares from Alfa Romeo Authorized
Services. Changing the windscreen wiper
blade (fig. 27)
WARNINGThe blade on driver’s side
is fitted with a spoiler that improves adhe-
sion between the blade and the windscreen.
To prevent improper fitting, before changing
the blade, check the spoiler direction of the
blade to be replaced, then fit the new blade
following the same spoiler direction.
fig. 27
A0B0580m
WINDSCREEN/REAR
SCREEN WIPERSBLADESPeriodically clean the rubber part using spe-
cial products TUTELA PROFESSIONAL
SC 35is recommended.
If the rubber blades are bent or worn they
should be replaced. In any case they should
be changed once a year.
A few simple notions can reduce the pos-
sibility of damage to the blades:
– If the temperature falls below zero,
make sure that ice has not frozen the rub-
ber against the glass. If necessary, thaw us-
ing an antifreeze product.
– Remove any snow from the glass: in ad-
dition to protecting the blades, this prevents
effort on the motor and overheating.
– Do not operate the windscreen and rear
window wipers on dry glass.
Driving with worn wiper
blades is a serious hazard,
because visibility is reduced in bad
weather.
WARNING

TECHNICAL SPECIFICATIONS
319
2.0 JTS
63
●9 ●6.9
4.4 ◆2
–
–
–
2,5
5.32.0 JTS
Selespeed63 ●9 ●6.9
4.4 ◆2
–
0.6
–
2,5
5.3 1.8
T.SPARK
63
●9 ●6.9
4.4 ■2
–
–
–
2,5
5.3 1.6
T.SPARK
63
●9 ●6.9
4.4 ■2
–
–
–
2,5
5.32.5 V6
24V
63
●9 ●9.2
5.9 ■–
2
–
–
2,5
5.3JTD
63
❍9 ❍6.1
4.5 ❑2
–
–
–
2,5
5.3 2.5 V6
24V
Q-System63 ●9 ●9.2
5.9 ■–
–
–
3.8
2,5
5.3
REFILLING
JTD 20V
Multijet
63
❍9 ❍7.25
5 ❑
3.1
–
–
–
2,5
5.3
JTD 16V
Multijet
63
❍9 ❍6.1
4.5 ❑
2
–
–
–
2,5
5.3
Fuel tank: litres
– including a reserve of litresEngine cooling system litres
Oil sump and filter litresMechanical gearbox/differential litres
Mechanical gearbox/differential litres
Selespeed gearbox litresactuation hydraulic system
Q-System litresautomatic gearbox
Windscreen washer and
rearscreen washer fluid
reservoir: litres– with headlamp washer litresSpecified fuels
Recommended products
●Unleaded petrol at not
less than 95 R.O.N
(specification EN228)❍Diesel fuel for motor
vehicles (Specification EN590)Mixture of distilled water and
PARAFLU 11(blue) at 50% or
PARAFLU UP(red) at 50%■ SELENIA 20K for Alfa
Romeo◆SELENIA RACING❑ SELENIA WR
TUTELA CAR
ZC 75 Synth
TUTELA CAR MATRYX
TUTELA CAR CS SPEED
TUTELA GI/2
Mixture of water and liquid
TUTELA PROFESSIONAL
SC 35
■
For decidedly sportive use of the car, fully synthetic SELENIA RACING
SAE
10W-60 engine oil is recommended.
For use in particularly harsh weather conditions SELENIA PERFORMER MULTIPOWER
SAE
5W-30 engine oil is recommended.

TECHNICAL SPECIFICATIONS
320
FLUIDS AND LUBRICANTSUSABLE PRODUCTS AND THEIR SPECIFICATIONSUse Quality features of fluids and lubricants Recommended fluids Applications
for correct vehicle operation and lubricants
Lubricants for petrol
engines 2.0 JTS
and 2.0 JTS Selespeed
Lubricants for petrol engines (*)Lubricants for
diesel engines (*) For decidedly sportive use of the car fully synthetic SELENIA RACING SAE 10W60 engine oil is recommended.
For use in particularly harsh weather conditions SELENIA PERFORMER MULTIPOWERSAE 5W-30 engine oil is recommended.
SELENIA PERFORMER MULTIPOWERis not required when using SELENIA RACING10W-60 engine oil.
WARNINGDo not top up with oil with different specifications that the oil already in the engine.Synthetic oil, SAE 10W-60 grade
Synthetic-based engine oil, SAE 10W-40 grade
that pass ACEA A3 and API SL specifications.
Synthetic-based engine oil SAE 5W-30 grade,
that pass API SL, ACEA A1-A5, FIAT 9.55535-M1 specifications.
Synthetic-based engine oils SAE 5W-40 grade
that pass ACEA B4 and API CF, FIAT 9.55535-M2 specifications.SELENIA RACING
SELENIA 20K
for Alfa Romeo
SELENIA PERFORMER
MULTIPOWER
SELENIA WR
A0B0682m

TECHNICAL SPECIFICATIONS
321
UseLubricants and greases
for transmissionsBrake fluidProtective agent for radiatorsAdditive for fuel oil
Windscreen/
rearscreen/headlampwasher fluid
(*) IMPORTANTDo not add or mix with fluids with specifications other than the specified ones.Quality features of fluids and lubricants
for correct vehicle operation
Synthetic-based engine oil, SAE 75W-80 EP grade that passes API GL5
and MIL-L-2105 D Lev specifications
SAE 75W-85 completly synthetic engine oil.
Meets API GL 4 and ZF TE ML06 (B&C) LEVEL, ALLISON C4 specifications
“ATF DEXRON II D LEV”, type oil
“ATF DEXRON III” type specific oil
“ATF DEXRON II D LEV”, SAE 10W type oil
Lithium-soap-based grease with molybdenum bisulphate.
Consistency NLGI 2
FMVSS n° 116 DOT 4, ISO 4925, SAE J1704,
CUNA NC 956-01 synthetic fluid
Protective with antifreeze action, blue color, based on inhibited monoethylene
glycol, CUNA NC 956-16
Protective with antifreeze action, red colour, based on inhibited monoethylen
glycol, with O.A.T.-based organic formula, that passes CUNA NC 956-16,
ASTM D 3306 specifications
Additive for fuel oil with protective action for Diesel engines
Mixture of spirits and surface-active agents CUNA NC 956-11Recommended fluids
and lubricants
TUTELA CAR
ZC 75 Synth
TUTELA CAR
MATRYX
TUTELA GI/2
TUTELA CAR
CS SPEED
TUTELA GI/A
TUTELA MRM 2
TUTELA CAR TOP 4
for Alfa Romeo
PARAFLU 11 (*)
or
PARAFLU UP (*)
DIESEL MIX
TUTELA
PROFESSIONAL
SC 35
Applications
Mechanical gearbox and
differential
Mechanical gearbox and
differential for high
temperatures
Automatic gearbox
Selespeed transmission
electrically-operated
electrohydraulic drive
Hydraulic power steering
C.V. joints
Hydraulic brake and
clutch control
Cooling ducts
Percentage:
50% down to –35°C
To be mixed with the fuel
oil (25 cc per 10 litres)
To be used neat
or diluted