2007 Acura TSX dead battery

CONT INUED
To select a memorized position, do
this:Make sure the parking brake is set
(M/T) or the shif t lever is in Park
(A/T).
Press the desired memory button
(1 or 2) until you hear a beep.
Doing any of the f ollowing af ter
pressing the MEMO button will
cancel the storing procedure.
Not pressing a memory button
within 5 seconds.
Readjusting the seat position.
Each memory button stores only one
driving position. Storing a new
position erases the previous setting
stored in that button’s memory. If
you want to add a new position while
retaining the current one, use the
other memory button.
All stored driving positions will be
lost if your vehicle’s battery goes
dead or is disconnected. Pressing the MEMO button again
within 5 seconds.
Press and release the MEMO
button on the driver’s door. You
will hear a beep. Then, both
indicators in the memory buttons
will start to blink. Press and hold
one of the memory buttons (1 or
2) within 5 seconds af ter you press
the MEMO button. When the
system completes storing a new
driving position, you hear two
beeps. The indicator in the stored
memory button will come on. 1.
2.
3.
Driving Position Memory System
Selecting a Memorized Position
Inst rument s and Cont rols
143
MEMORY BUTTONS
MEMORY BUTTONS MEMO BUTTON
INDICATORS

µIf the driver’s
window senses any obstacle while it
is closing automatically, it will
reverse direction, and then stop. To
close the window, remove the
obstacle, then use the window switch
again.
Auto reverse stops sensing when the
window is almost closed. You should
always check that all passengers and
objects are away from the window
bef ore closing it. If your vehicle’s battery is
disconnected or goes dead, or the
driver’s window f use is removed, the
AUTO f unction may be disabled. If
the AUTO f unction is disabled, the
power window system will need to be
reset af ter reconnecting the battery
or installing the f use.
The power window system has a key-
of f delay f unction. The windows will
still operate f or up to 10 minutes
after you turn off the ignition switch.
Opening either f ront door cancels
the delay function. You must turn
the ignition switch to the ON (II)
position again bef ore you can raise
or lower the windows.
If the power windows do not operate
properly af ter resetting, have your
vehicle checked by your dealer. Pull and hold the driver’s window
switch to close the window
completely, then hold the switch
f or about 2 seconds. Start the engine. Push down and
hold the driver’s window switch
until the window is f ully open.
1.
2.
AUTO REVERSE
Power Windows
148

µ
µ
µ
CONT INUED
The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM. Pick the preset number (1 6)
you want for that station. Press
the button or icon and hold it until
you hear a beep.
Each preset button or icon
can store one f requency on AM, and
two f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button or icon.
To use the SCAN, preset and A.SEL
f unction, press the AUDIO DISPLAY
button to view these icons.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button, or
touch the SCAN icon (models with
navigation system), then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor5seconds.Whenit
plays a station you want to listen to,
press the SCAN button or touch the
SCAN icon again. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
3.
4.
1.
2.
On vehicles with navigation system
Playing the AM/FM Radio
Preset
SCAN
Features
173

µ
Your vehicle’s audio system will
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic digit code using the
preset buttons (icon on vehicle’s with
navigation system). Because there
are hundreds of number
combinations possible f rom specif ic
digits, making the system work
without knowing the exact code is
nearly impossible. If your vehicle’s battery is discon-
nected or goes dead, the audio
system will disable itself . If this
happens, you will see ‘‘CODE’’ on the
frequencydisplaythenexttimeyou
turn on the system. Use the preset
buttons (icons on vehicles with
navigation system) to enter the f ive-
digit code. The code is on the radio
code card included in your owner’s
manual kit. When it is entered
correctly, the radio will start playing.
If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code. If you are
unsuccessf ul in 10 attempts, you
must then leave the system on for 1
hour bef ore trying again.If the code card is lost, a dealer can
access your code with your radio’s
serial number. To access the serial
number, turn the radio on. It must
display ‘‘CODE’’, then turn the radio
of f . Push the preset 1, preset 6, and
power buttons at the same time, then
quickly release.
You will have to store your favorite
stations on each side of the preset
buttons (1 6) after the system
begins working. Your original
settings were lost when power was
disconnected.
If you lose the card, you must obtain
the code number f rom a dealer. To
do this, you will need the system’s
serial number. Youshouldhavereceivedacardthat
lists your audio system code number
and serial number. It is best to store
this card in a saf e place at home. In
addition, you should write the audio
system’s serial number in this owner’s
manual.
Radio T hef t Protection
Features
201

For example:1:06 would RESET to 1:00.
1:52 would RESET to 2:00.
Refer to the navigation system
owner’s manual to set up the time.
If your vehicle’s battery is
disconnected or goes dead, you may
need to set the clock.
To set or change the time, press and
hold the TUNE/SOUND knob until
you hear a beep. The displayed time
begins to blink. Press on the H
(Preset 4) until the numbers advance
to the desired time. Change the
minutes by pressing the M (Preset
5) until the numbers advance to the
desired time. When you are f inished,
press the TUNE/SOUND knob
again to set the time.
You can quickly set the time to the
nearest hour. If the time displayed is
bef ore the half hour, press and hold
the TUNE/SOUND knob, then press
theR(Preset6)tosetthetimeback
to the previous hour.
If the time displayed is af ter the half
hour, the same procedure sets the
time f orward to the beginning of the
next hour.
On vehicles without navigation system
On vehicles with navigation system
Setting the Clock
202
TUNE/SOUND
KNOBR BUTTON
M BUTTON
DIGITAL CLOCK
H BUTTON

µ
Todothis,pressandholdthetwo
outside buttons on the HomeLink
transceiver for about 20 seconds,
until the red indicator f lashes.
Release the buttons, then proceed to
step 1. If you just
received your vehicle and have not
trained any of the buttons in
HomeLink bef ore, you should erase
any previously learned codes bef ore
training the f irst button.
If you are training the second or
third buttons, go directly to step 1.
Unplug the garage door opener
motor f rom the electrical outlet.
Holdtheendof thegaragedoor
opener remote 2 to 5 inches f rom
HomeLink. Make sure you are not
blocking your view of the red
indicator in HomeLink.
The HomeLink
universal
transceiver built into your vehicle
canbeprogrammedtooperateupto
three remotely controlled devices
around your home, such as garage
doors, lighting, or home security
systems.
If you are training HomeLink to
operate a garage door or gate, you
should unplug the motor f or that
device during training. Repeatedly
pressing the remote control button
could burn out the motor.
HomeLink stores the code in a
permanent memory. There should
be no need to retrain HomeLink if
your vehicle’s battery goes dead or is
disconnected. If your garage door
opener was manuf actured bef ore
April 1982, you may not be able to
program HomeLink to operate it.
They do not have the saf ety f eature
that causes the motor to stop and reverse if an obstacle is detected
during closing, increasing the risk of
injury.
Always ref er to the opening
instructions and saf ety inf ormation
that came with your garage door
opener or other equipment you
intend to operate with HomeLink. If
you do not have this inf ormation,
contact the manuf acturer of the
equipment.
For quick and accurate training,
make sure the remote transmitter
for the device (garage door,
automatic gate, security system, etc.)
has a fresh battery.
1.
2.
CONT INUED
T raining HomeL ink
General Inf ormation Important Saf ety Precautions
Bef ore you begin
HomeL ink Universal Transceiver
Features
207

µµµ µ
µ
µ
CONTINUED
To
shift from:
PtoR
RtoP
NtoR
DtoD DtoN
DtoD NtoDRtoN Do
this:
Press the brake pedal
and move the lever.
Move the lever.
3
3
To avoid transmission damage, come
to a complete stop before shifting
into Park. The shift lever must be in
Park before you can remove the key
from the ignition switch.
Press the brake
pedal, and move the shift lever from
Park to reverse. To shift from
reverse to neutral, come to a
completestop,andthenshift.
Your vehicle has a reverse lockout so
you cannot accidentally shift to
reverse from neutral or any other
driving position when the vehicle
speed exceeds 5 6 mph (8 10
km/h).
If you cannot shift to reverse when
the vehicle is stopped, press the
brake pedal, slowly shift to neutral,
andthenshifttoreverse. Use
neutral if you
need to restart a stalled engine, or if
it is necessary to stop briefly with
the engine idling. Shift to the Park
position if you need to leave your
vehicle and apply the parking brake.
Press on the brake pedal when you
are moving the shift lever from
neutral to another gear.
Use this position for
your normal driving. The
transmission automatically selects a
suitable gear for the vehicle speed
and acceleration. You may notice the
transmission shifting up at higher
speeds when the engine is cold. This
helps the engine warm up faster.
If
you have done all of the above and
still cannot move the lever out of
Park, see on
page .This
position mechani-
cally locks the transmission. Use
Park whenever you are turning off or
starting the engine. To shift out of
Park, you must press on the brake
pedal and have your foot off the
accelerator pedal. Move the shift
levertotherighttoshiftoutofPark.
If there is a problem in the reverse
lockout system, or your vehicle’s battery
is disconnected or goes dead,
you cannot shif t to reverse. (Ref er to on page ).
251 251
Automatic Transmission
Reverse (R)
Neutral (N)
Drive (D)
Shif t L ock Release
Park (P)
Shif t L ock Release
Driving
247

Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics for the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed. To
check if they are set, turn the
ignition switch to the ON (II)
position, without starting the engine.
The malfunction indicator lamp will
come on for 20 seconds. If it then
goes off, the readiness codes are set.
If it blinks five times, the readiness
codes are not set. If possible, do not
take your vehicle for a state
emissions test until the readiness
codes are set. Refer to
for more
info rmation (see page ).
If
the battery in your vehicle has
been disconnected or gone dead,
thesecodesmaybeerased.Ittakes
several days of driving under various
conditions to set the codes again.
If
your vehicle has an automatic
transmission, the malfunction
indicator lamp may also come on
with the ‘‘D’’ indicator.
You will also see a ‘‘CHECK
EMISSION SYSTEM’’ message on
the multi-information display (see
page ). 357
84 Readiness Codes
State
Emissions T esting
Malf unction Indicator L amp
T aking Care of t he Unexpect ed
333
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and engine. Those repairs may
not be covered by your vehicle’s
warranties.