2007 Acura TSX trunk

Open the trunk.
Pull the lining back caref ully.Determine which of the two bulbs
is burned out: taillight or back-up
light.
To replace a bulb on the right side,
remove the trim clip. For the lef t
side, remove the two trim clips. Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to test the new
bulb.
Reinstall the trunk lid trim. Make
sure it is installed under the edge
of the trunk lid seal.
Press the trim clips back into their
holes.
1.
2. 5.
6. 4.
3. 7.
8.
9.
10.
Replacing Rear Bulbs
(in T runk L id)
Lights
Maint enance
303
SOCKETS BULBS
TRIM CLIPS

Open the trunk, and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
1.
2.
3. Replacing a High-mount Brake
Light Bulb Side T urn Signal L ight
Rear L icense Plate BulbReplacing a Front Fog L ight Bulb
Lights
304
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.

Block the rear wheels.
If the vehicle is to be stored f or a
longer period, it should be
supported on jackstands so the
tires are of f the ground.
Leave one window open slightly (if
the vehicle is being stored
indoors).
Disconnect the battery.
Support the f ront wiper blade
arms with a f olded towel or rag so
they do not touch the windshield.
To minimize sticking, apply a
silicone spray lubricant to all door
and trunk seals. Also, apply a
vehiclebodywaxtothepainted
surfaces that mate with the door
and trunk seals.
If you need to park your vehicle f or
an extended period (more than 1
month), there are several things you
should do to prepare it f or storage.
Proper preparation helps prevent
deterioration and makes it easier to
get your vehicle back on the road. If
possible, store your vehicle indoors.
Fill the f uel tank.
Change the engine oil and f ilter.
Wash and dry the exterior
completely.
Cleantheinterior.Makesurethe
carpeting, floor mats, etc., are
completely dry. Leave the parking brake off. Put
the transmission in reverse
(manual) or Park (automatic).
Cover the vehicle with a
‘‘breathable’’ cover, one made
f rom a porous material such as
cotton. Non-porous materials, such
as plastic sheeting, trap moisture,
which can damage the paint.
If possible, periodically run the
engine until it reaches f ull
operating temperature (the
cooling f ans cycle on and of f
twice). Pref erably, do this once a
month.
Vehicle Storage
Maint enance
317

CONT INUED
Park the vehicle on f irm, level and
non-slippery ground. Put the
transmission in Park (automatic)
or reverse (manual). Apply the
parking brake.
If you have a f lat tire while driving,
stop in a saf e place to change it.
Drive slowly along the shoulder until
you get to an exit or an area that is
far away from the traffic lanes.
Turn on the hazard warning lights,
and turn the ignition switch to the
LOCK (0) position. Have all
passengers get out of the vehicle
while you change the tire.
2.
1.
Changing a Flat Tire
T aking Care of t he Unexpect ed
321
TRUNK FLOOR
JACK TOOLS
TOOL TRAY
The vehicle can easily roll off
the jack, seriously injuring
anyone underneath.
Follow the directions for
changing a tire exactly, and
never get under the vehicle
when it is supported only by the
jack.

Open the trunk. Raise the trunk
f loor by lif ting up on the back edge.
Take the tool tray out of the trunk,
and remove the tools and the jack.
Unscrew the wing bolt and take
the spare tire out of the trunk.
Loosen each wheel nut 1/2 turn
with the wheel nut wrench.Place the jack under the jacking
point nearest the tire you need to
change. Turn the end bracket
clockwise until the top of the jack
contacts the jacking point. Make
sure the jacking point tab is
restinginthejacknotch.
Use the extension and the wheel
nut wrench as shown to raise the
vehicle until the f lat tire is of f the
ground.
Remove the wheel nuts and f lat
tire. Handle the wheel nuts
caref ully; they may be hot f rom
driving. Place the f lat tire on the
ground with the outside surf ace of
the wheel f acing up.
7.
3.
4.
5.
6. 8.
9.
Changing a Flat Tire
322
JACKING POINT
TOOL TRAY WHEEL NUT WRENCH
EXTENSION

Securetheflattirebyscrewing
the wing bolt back into its hole.
Store the jack and tools in the tool
tray, and place the tool tray back
in the trunk. Store
the wheel cover or center
cap in the trunk. Make sure it does
not get scratched or damaged.
Lower the trunk floor, then close
the trunk lid.
Remove the center cap before
storing the flat tire in the trunk
well.
Place the flat tire face down in the
spare tire well.
Remove the spacer cone from the
wing bolt, turn it over, and put it
back on the bolt. Refer to
(see page ).
19.
20.
17.
18.
14.
15.
16. 260
Changing a Flat Tire
Changing a T ire with
TPMS
324
WING BOLT
For
spare
tireFor
normal
tire
SPACER CONE
Loose items can fly around the
interior in a crash and could
seriously injure the occupants.
Store the wheel, jack, and tools
securely before driving.

Use a screwdriver or coin to
remove the round plug in the
center of the headliner.
Insert the moonroof wrench into
the socket behind this plug. Turn
the wrench until the moonroof is
fully closed.
Remove the wrench. Reinstall the
round plug. If
you need to close the moonroof
manually, it means the moonroof
opening/closing function is
developing a problem. Have your
vehicle checked by your dealer.
If
the electric motor will not close
the moonroof, do the following:
Check the f use f or the moonroof
motor (see page ). If the f use
is blown, replace it with one of the
same or lower rating.
Try closing the moonroof . If the
new f use blows immediately or the
moonroof motor still does not
operate, you can close the
moonroof manually.
Get the moonroof wrench out of
the tool kit in the trunk. 5.
6.4.
3. 1.
2. 340
Closing t he Moonroof
T aking Care of t he Unexpect ed
335
SOCKET
ROUND PLUG
MOONROOF WRENCH

µ
Î µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
CONTINUED
Specifications
T
echnical Inf ormat ion
347
Lights Battery
Alignment Fuses
Engine
55
W
35 W
12 V
12
V
12
V
12 V
3CP 21 W
12
V 55 W
Headlights
Front
fog lights
Front turn signal
Front parking lights/
Side marker lights
Rear turn signal lights
Stop/Taillights
Taillights
High-mount brake light
Back-up lights
Rear side marker lights
License plate light
Ceiling light
Spotlights/Front ceiling lights
Trunk light
Door courtesy lights
Vanity mirror lights 12 V 1.1 W
2CP
12 V
12
V 5 W
8W
12 V 8W
12 V
12
V 3 CP
3CP
12 V
12
V 21 W
21
W
12 V 5W
12 V
12
V 21/5 W
21
W
12 V Capacity
12 V 36 AH/5 HR
On vehicles with high voltage discharge type headlights,
replacement of a headlight bulb should be performed by your dealer. Toe-in
Camber
Caster 3°13’1°
0°
0.08
in (2.0 mm)
0.00
in (0.0 mm)
Interior
Under-hood
Type
BorexStroke
Displacement
Compression
ratio
Spark plugs
SKJ20DR-M11 IZFR6K-1110.5
: 1
144
cu-in (2,354 cm
)
3.43
x 3.90 in (87.0 x 99.0 mm)
Water
cooled 4-stroke, DOHC
i-VTEC 4-cylinder, gasoline engine
See
page 340 or the fuse label
attached to the inside of the fuse
box door on each side of the
dashboard.
See page 339 or the fuse box
cover.
Front
Rear
Front
Rear
Front
High
Low
NGK:
DENSO:
: