2007 Acura TSX ECO mode

µµ
To
change the ‘‘INTERIOR LIGHT
DIMMING TIME,’’ see page .
If you unlock the doors with the
remote transmitter, but do not open
anydoorswithin30seconds,the
doors automatically relock and the
security system sets. To change this
setting, refer to ‘‘SECURITY
RELOCK TIMER’’ on page .
Each remote transmitter also
activates the Driving Position
Memory System and changes the
‘‘MEMORY POSITION LINK’’
setting according to that remote (see
page ).
Pressthisbuttonfor
about 1 second to attract attention;
thehornwillsoundandtheexterior
lights will f lash f or about 30 seconds.
To cancel panic mode, press any
other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position.
Pressthisbuttonfor
about 1 second to open the trunk.
You cannot open the trunk if the key
is in the ignition switch.
142
106
115 Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
132
DRIVER 1 REMOTE DRIVER 2 REMOTE

To open: You can open and close the windows
with the key in the driver’s door lock.Insert the key in the driver’s door
lock.
Turn the key clockwise, then
release it.
You can open all of the windows
from the outside with the remote
transmitter.
Press the UNLOCK button once
to unlock the driver’s door
(depending on the ‘‘DOOR LOCK
MODE’’ setting).
Press the UNLOCK button a
second time, and hold it. The
passenger’s doors unlock, and all
f our windows start to open. To
stop the windows, release the
button.
To open the windows further,
press the button again (within 10
seconds).
You cannot close the windows with
the remote transmitter. Turnthekeyclockwiseagain,and
hold it. All f our windows start to
open. To stop the windows,
release the key.
To open the windows f urther, turn
andholdthekeyagain(within
10 seconds).
To close: Insert the key in the driver’s door
lock.
Turn the key counterclockwise,
then release it.
Turn the key counterclockwise
again, and hold it. All four
windowsstarttoclose.Tostopthe
windows, release the key.
To close the windows f urther, turn
andholdthekeyagain(within
10 seconds).
1.
2.
3.
1.
2.1.
2.
3. 3.
4.
4.
Power Windows
Opening t he Windows wit h t he
Remote Transmitter
Opening/Closing t he Windows wit hthe Key
Inst rument s and Cont rols
149
Open
Close UNLOCK BUTTON

µ
µ
µ
CONT INUED
The preset f requencies may be lost if
your vehicle’s battery goes dead, is
disconnected, or the radio f use is
removed. Repeat steps 1 through 3 to store a
total of six stations on AM and
twelve stations on FM. Pick the preset number (1 6)
you want for that station. Press
the button or icon and hold it until
you hear a beep.
Each preset button or icon
can store one f requency on AM, and
two f requencies on FM.
Select the desired band, AM or
FM. FM1 and FM2 let you store
two f requencies with each preset
button or icon.
To use the SCAN, preset and A.SEL
f unction, press the AUDIO DISPLAY
button to view these icons.
The SCAN f unction
samples all stations with strong
signals on the selected band. To
activate it, press the SCAN button, or
touch the SCAN icon (models with
navigation system), then release it.
You will see SCAN in the display.
The system will scan f or a station
with a strong signal. When it f inds
one, it will stop and play that station
f or about 5 seconds.
If you do nothing, the system will
then scan f or the next strong station
andplayitfor5seconds.Whenit
plays a station you want to listen to,
press the SCAN button or touch the
SCAN icon again. UsetheTUNE,SEEK,orSCAN
function to tune the radio to a
desired station.
3.
4.
1.
2.
On vehicles with navigation system
Playing the AM/FM Radio
Preset
SCAN
Features
173

µ
µ If you are
traveling far from home and can no
longer receive your preset stations,
you can use the auto select feature to
find stations in the local area. If you do not like the stations Auto
Select has stored, you can store
other f requencies on the preset
buttons or icons. Use the TUNE,
SEEK, or SCAN f unction to f ind
stations, then store them in the
preset buttons or icons as described
previously.
Press the A. SEL button or touch the
A. SEL icon. A. SEL will appear in
the display, and the system will go
into scan mode f or several seconds.
It stores the f requencies of six AM,
and twelve FM stations in the preset
buttons (1 6) or icons. You will
see a ‘‘0’’ displayed af ter pressing a
preset button or icon if Auto Select
cannot f ind a strong station f or every
preset button or icon. press the
A.SEL button or touch the A.SEL
icon. This restores the presets you
originally set.
To turn of f Auto Select,
AUTO SELECT
Playing the AM/FM Radio
174

µ
µ Ifyouwanttoadjustthesoundwhile
the radio or CD is playing, push the
AUDIO DISPLAY button and then
push the TUNE/SOUND knob or
touch the SOUND icon in the display.
The current setting is shown on the
display.
You select which of these you want
to adjust by pressing the TUNE/
SOUND knob. The mode changes
from BASS to TREBLE to FADER to
BALANCE,andthenbacktothe
selected audio mode, each time you
press the knob. Turn the knob to
adjust the setting to your liking.
When the level reaches the center,
you will see ‘‘ ’’ in the display.
The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode.
Bass, Treble, Balance, and Fader are
each adjustable.
These two
modes adjust the strength of the
sound coming f rom each speaker.
BAL adjusts the side-to-side strength,
while FAD adjusts the f ront-to-back
strength.
Use the TRE/BAS
modes to adjust the tone to your
liking.
On vehicles without navigation system On vehicles with navigation system
CONT INUED
Adjusting the Sound
Balance/Fader
Treble/Bass
Features
175

´µ
You select which of these you want
to adjust by pressing the TUNE/
SOUND knob. The mode changes
from BASS to TREBLE to FADER to
BALANCE,andthenbacktothe
selected audio mode, each time you
press the button. You can also select
themodebytouchingthe
adjustment bar on the display
directly. To adjust the TREBLE and BASS,
touch or on each side of the
TREBLE or BASS adjustment bar.
The adjustment bar shows you the
current setting.
The Left/Right BALANCE adjusts
the side-to-side strength, while
Front/Rear FADER adjust the front-
to-back strength. To adjust the Left/
Right BALANCE, touch the ‘‘L’’ or
‘‘R’’ icon. To adjust the Front/Rear
FADER, touch the ‘‘FR’’ or ‘‘RR’’ icon.
The system will automatically return
the display to the selected audio
mode about 5 seconds af ter you stop
adjusting a mode.
Adjusting the Sound
176
ADJUSTMENT BARS

µ
µ
µ Youcanstoreupto12
preset channels using each side of
the preset bar or preset icons on the
screen. Each side of the bar stores
one channel f rom the XM1 band and
one channel f rom the XM2 band. Pick a preset number (icon) you
want f or that channel. Press and
hold the bar (icon) until you hear a
beep.
Repeat steps 2 and 3 to store the
f irst six channels.
Once a channel is stored, press and
release the proper side of the preset
bar (icon) to tune to it.
To store a channel:
Press the XM button. Either XM1
or XM2 will show in the display.
Usethetune,seek,orscan
function to tune to a desired
channel. Press the XM button again or
touch the other XM icon (XM1 or
XM2) on the audio display. Store
the next six channels using steps 2
and 3.
In category mode, only channels
within that category can be selected.
In channel mode, all channels can be
selected.
Press either side of the CATEGORY
bar ( or ) to select another
category.
The scan f unction gives
you a sampling of all channels while
in the channel mode. In the category
mode, only the channels within that
category are scanned. To activate
scan, press the SCAN button or
touch the SCAN icon on the screen.
The system plays each channel in
numerical order f or a f ew seconds,
then selects the next channel. When
you hear a channel you want to listen
to, press the button or touch the icon
again. 1.
2.3.
4.
5.
CONT INUED
Preset
SEEK /SK IP (CA T EGORY)
SCAN
Playing the XMSatellite Radio (U.S. Models)
Features
181

To take the system out of CD mode,
press the AM/FM or CD/AUX, or
CD/AUX/XM button to switch to
the radio or satellite radio (U.S.
models only), or optional tape player
(if a tape is loaded) while a CD is
playing. When you return to CD
mode by pressing the CD/AUX or
CD/AUX/XM button, play will
continue at the same point that it lef t
off.To remove the disc that is currently
playing, press and release the eject
( ) button. You will see EJECT
in the display. When you remove the
disc from the slot, the system begins
the load sequence so you can load
another disc in that position. If you
do not load another CD within 15
seconds, the system selects the
previous mode [AM, FM1, FM2, or
XM Radio (U.S. models)].
If you do not remove the CD f rom
the slot, the system will reload the
CD af ter 15 seconds and put the CD
changer in pause mode. To begin
playing the CD, press the CD button.
To remove a different CD from the
changer,firstselectitwiththe
appropriate preset button, or the
appropriate icon or CH/DISC bar.
When that CD begins playing, press
the eject button.Af ter that disc is ejected, pressing
the eject button again will eject the
next disc in numerical order. By
doing this six times, you can remove
all the CDs f rom the changer.
If you press the eject button while
listening to the radio, or with the
audio system turned of f , the disc
that was last selected is ejected.
In any mode, if you press the eject
button and hold it until you hear a
beep, the system will eject all of the
discs in the changer.
You can also eject discs when the
ignition switch is of f by pressing the
eject button. The disc that was last
selected is ejected f irst. You can
eject up to 5 discs, one at a time.
If you turn of f the system while a CD
is playing, either by pushing the
VOL/PWR knob or by turning of f
the ignition, the CD will stay in the
drive. When you turn the system
back on, it will begin at the same disc
and track.
Playing Discs
T o Stop Playing a CD
Removing CDs f rom the Changer
192