2007 Acura RL reset

ÛÝ
To exit SECURITY RELOCK
TIMER without changing the
current setting, select EXIT by
pressing the INFO ( / ) button,
then press the SEL/RESET button.
The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
security relock timer setup.
Multi-Inf ormation Display
132
——
y

y
(y
y

ÛÝÛ
Ý
ÛÝ
ÛÝ
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select WIPER SETUP by
pressing the INFO ( / ) button,
th en press the SEL/RESET button.
The
changeable setting under
WIPER SETUP is called WIPER
ACTION. To get into WIPER
ACTION, do this:
Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
WIPER ACTION, then press the
SEL/RESET button to enter your
selection.
CONTINUED
Wiper Setup
Multi-Information Display
Instru m ent sand Cont ro ls
133
Press the or button.
Press the SEL/RESET button. seepage134
——
y
y
(y
y

Û
Ý
µ
µ
You can select from these two
settings when the wiper switch is in
the INT (intermittent) position:
While the multi-information display
is in the WIPER SETUP screen of
the CUSTOMIZE GROUP, press the
SEL/RESET button. The screen
changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select INTERMITTENT or WITH
VEH SPD by pressing the INFO ( /
) button, then press the SEL/
RESET button to enter your
selection.
INTERMITTENT The
intermittent operation varies
according to the selection you make
on the wiper lever’s intermittent
control ring.
WITH VEH SPD The intermittent
operation varies according to vehicle
speed.
Wiper Action
Multi-Inf ormation Display
134
——
y

y
(y
y

ÛÝ
To exit WIPER ACTION without
changing the current setting, select
EXIT by pressing the INFO ( / )
button, then press the SEL/RESET
button. The screen goes back to
CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the
wiper action setup.
Multi-Inf ormation Display
Inst rument s and Cont rols
135
——
y
y
(y
y

When you turn the ignition switch to
the LOCK (0) position and release it,
or remove the built-in key from the
ignition switch, the steering wheel
au tomatically moves fully in and up.
Steering wheel movement is also
controlled by the driving position
memory system (see page ).
To change the ‘‘AUTO TILT &
TELESCOPIC’’ setting, see page
. If your vehicle’s battery is
disconnected or goes dead, or the
f use f or the power tilt and telescopic
steering wheel is removed, the
power tilt and telescopic steering
wheel system needs to be reset
when you reconnect the battery or
install the f use.
The steering wheel returns to its
original position when you push the
ignition switch or insert the built-in
key back in the ignition switch. Push the ignition switch f or more
than 1 second and release it, or
insert the built-in key into the
ignition switch, and remove it. The
steering wheel automatically moves
f ully in and up to let you know the
system is reset.
160
106
Steering Wheel A djustments
148
——
y

y
(y
y

Most audio system functions can still
be controlled by standard buttons,
dials, and knobs, but some functions
can only be accessed using the
interface dial. The interface dial has
two parts, a knob and a selector. The
selector can be pushed left,
right, up, down, and in. Use the
selector to scroll through lists, to
select menus, and to highlight menu
items. When you make a selection,
push the center of the selector
(ENTER)togotothatselection. The knob turns left and right. Use it
to make selections or adjustments to
a list or menu on the screen. When
you unlock the doors with
your remote and turn the audio
system on, the driver’s ID (Driver 1
or Driver 2) is detected, and the
radio preset memory (see page ),
the auto select preset memory (see
page ), and the volume and
sound level settings (see page )
are turned to the respective
memorized mode automatically.
The audio system can also be
operated by voice control.
See the Navi section in your quick
start guide for an overview of this
system, and the navigation system
manual for complete details.
Refer to Voice Control Basics for
complete details (see page ). 210
211 214
263
On models without navigation system
On models with navigation system
Interf ace Dial
Personalization Setting
Voice Control System
Audio System
Features
207
KNOB
ENTER
SELECTOR
——
y
y
(y
y

Audio System
Playing the AM/FM Radio
208
PRESET BUTTONSAM/FM
BUTTON
TUNE
BUTTONS TUNE
BUTTONS
AUTO
SELECT
BUTTON
AM BUTTON
FM BUTTON
AUDIO
DISPLAY
BUTTON SEEK
BUTTONS
AUDIO
DISPLAY
BUTTON
PRESET BUTTONS
UPPER DISPLAY
SCAN
BUTTON SEEK
BUTTONS SCAN
BUTTON
INTERFACE DIAL INTERFACE DIAL
POWER/
VOLUME
KNOB
POWER/
VOLUME
KNOB
U.S. models (Technology package model is shown)
Canadian and Hawaiian models
——
y
y
(y
y

µUse the TUNE button to
tune the radio to a desired f requency.
Press the button to tune to a
higher f requency, or the button
to tune to a lower f requency. To tune
with the interf ace dial, push the
selector down, and turn the knob to
TUNE. Then press ENTER on the
selector, and turn the knob to the
desired f requency. To exit the
TUNE mode, press ENTER on the
selector.
You can use any of f ive methods to
f ind radio stations on the selected
band:
the
preset buttons, and .
The ignition switch must be in the
ACCESSORY (I) or the ON (II)
position. Press the AUDIO button to
view the audio control display. Turn
the system on by pressing the
power/volume knob or the AM/FM
button (AM or FM button on
Canadian and Hawaiian models).
Adjust the volume by turning the
power/volume knob. The band and f requency that the
radio was last tuned to are shown on
the display. To change bands, press
the AM/FM button (AM or FM
buttononCanadianandHawaiian
models). You can also change bands
by pushing the interf ace selector up.
Each time you push it up, the band
will change to FM1, FM2, or AM. On
the FM bands, STEREO will be
shown on the navigation screen and
ST on the upper display, if the
stationisbroadcastinginstereo.
Stereo reproduction on AM is not
available.
CONT INUED
TUNE
To Select a Station TUNE,SEEK,SCAN, AUTO SELECT
Audio System
Features
209
STEREO ICON
TUNE ICON
BAND
——
y
y
(y
y