2007 Acura RL bulb

This indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. This
indicator has three functions:
Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes when VSA is active (see
page ).
This indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. For more information, see
page . The
left or right turn signal indicator
blinks when you signal a lane change
or turn. If the indicator does not
blink or blinks rapidly, it usually
means one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signals blink. All
turn signals on the outside of the
vehicle should flash.
It
comes on along with the VSA
system indicator if there is a
problem with the VSA system.
You will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
information display (see page ).
Ifitcomesonandstaysonatany
other
time, or it does not come on
wh en you turn the ignition switch to
the ON (II) position, there is a
problem with the VSA system. You
will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
info rmation display (see page ).
Take your vehicle to a dealer to have
it checked. Without VSA, your
vehicle still has normal driving ability,
but will not have VSA traction and
stability enhancement. For more
info rmation, see page . 1.
2.
3.
78 78
371 371371
406
Instrument Panel Indicators
Vehicle Stability Assist
(VSA ) System IndicatorVSA Activation Indicator
Turn Signal and
Hazard Warning
Indicators
Inst rument s and Cont rols
65
——
y

y
(yy

The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
ci rcuit even with the light switch off
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself. If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced. Your
vehicle has halogen high beam
headlight bulbs which are also used
for the daytime running light.
Handle it by its base and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Your
vehicle is equipped with an
automatic headlight adjusting
system that adjusts the vertical angle
of the headlights automatically.
Refer to page for more
inf ormation.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer (if applicable),
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied technician. 144
Lights
Headlight A iming
Replacing a Headlight/Daytime
Running L ight Bulb
404
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
——
y


y
(yy

CONTINUED
Remove the electrical connector
from the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Remove
the left or right side
engine compartment cover from
thesideyouareworkingonby
carefully pulling the cover out (see
page ).
Ifyouarereplacingthebulbon
the driver’s side, remove the
ba ttery cover (see page ), then
remove the battery hold-down by
removing the two nuts with a 10
mm wrench. Then caref ully slide
the battery toward the engine to
access the bulb. 2.
3.
1.
394
424
Lights
Maint enance
405
NUTSBULB
BATTERY HOLD-DOWN CONNECTOR
——
y

y
(y
y

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Reinstall the engine compartment
side cover.
Push
the electrical connector back
onto the bulb. Make sure it is on
all the way.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Reinstall
the battery in the reverse
order of removal, and reinstall the
cover on the battery. Remove
the left or right side
engine compartment cover from
thesideyouareworkingonby
carefully pulling the cover out (see
page ).
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
2.
1.
4.
5.
6.
7.
8.
3.
394
424
Lights
Replacing a Front T urn Signal/
FrontParkingLightBulb
406
SOCKET
BULB
——
y


y
(y

y

CONTINUED
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
Use a flat-tipped screwdriver to
remove the holding clip from the
windshield washer reservoir.
(Passenger’s
side)
Remove
the left or right side
engine compartment cover (see
page ).
Pull the bulb straight out of its
socket. Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
Reinstall the engine compartment
side cover.
1.
2.
5.
6.
7.
8. 394
424
4.
On model without adaptive f ront
lighting system
Lights
Replacing a Front Position/Side
Marker L ight Bulb
Maint enance
407
SOCKET
BULB
——
y

y
(y
y

Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
(Passenger’s side)
Reinstall the windshield washer
reservoir.
Reinstall the engine compartment
side cover.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. 5.
6.
7.
8.
9.
3.
4.
Lights
ReplacingaFogLightBulb
408
SOCKET
HOLDING CLIP
BULB
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
——
y

y
(y
y

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two mounting bolts
onthesideundercoverand
tighten them securely. Put the
holding clip back on the side
under cover and push on the
center until it locks (the center is
flushwiththehead).
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Caref ully push up the side under
cover into the bumper. Use a Phillips-head screwdriver to
remove the two mounting bolts,
and remove the holding clip with a
f lat-tipped screwdriver. 3.
4. 5.
6.
8. 7.
1.
2.
Lights
Maint enance
409
CLIP CONNECTORBULB
BOLTS
——
y

y
(y
y

Determine which of the two bulbs
is burned out: turn signal or back-
up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Carefully pry in the top or bottom
edge of the trim with a small f lat-
tipped screwdriver, and pull the
trim straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.
2. 1.
3.
4.
5.6.
7.
8.
Lights
Replacing Rear Bulbs
410
MOUNTING NUT
MAINTENANCE LID BOLTS
BULBS
TAIL LIGHT TRIM SOCKETS
——
y

y
(y
y