2007 Acura RDX Info button

Diagnostic inf o and recall/
campaign messages can only be
deleted by your dealer.
To delete a single message: Press the INFO button to bring up
the Information screen.
Scroll to the Messages option,
then select it by pressing ENTER
on the interf ace selector.
Usetheinterfaceknobtoscrollup
or down to the message title you
want to delete, and select it by
pressing ENTER on the interf ace
selector.
Scroll to Delete with the interface
knob, and select it by pressing
ENTER on the interf ace selector. When you open a message, you can
read a summary of it, and then
choose one of several options. If an
option is not available f or a message,
that button will not be highlighted.
Scroll to the category with the
messages you want to delete, and
selectthecategorybypressing
ENTER on the interf ace selector. Scroll to the Delete Messages
option, and select it by pressing
ENTER on the interf ace selector. Usetheinterfaceknobtoscrollto
the AcuraLink/Messages button,
and select it by pressing ENTER
on the interf ace selector. Select MORE by pushing the
interface selector to the right. Press the SETUP button to view
the setup screen. The Delete All Messages
command only works f or quick tip
and maintenance minder messages.
Other messages must be deleted
individually. To delete all messages:
AcuraLink
Deleting Messages Message Options
246
NOTE:NOTE:
——
y
y
() y
y

µ
µ
µ
µ µ
µ To
set your AcuraLink preferences
(thetypesofmessagesyouwantto
receive, if an y), visit the Own er Link
website at
www.ow ners.acura.com,
and choose what you would like to
receive. If you do not have internet
access, call Acura Client Services at
(800) 382-2238; they can set your
message preferences for you.
Select
this button to
delete the current message.
Select this button to hear a
voice read the entire message. This
gives you more information than the
screen can display at one time. When
you select the Voice button, it
ch anges to a Stop Reading button.
Select the button again to stop the
voice.
Select this button to call a
phone number embedded in the
message. When you select , the
HandsFreeLink (HFL) dials the
number for you.
To make a call, your Bluetooth
compatible phone must be paired to
your vehicle’s HandsFreeLink (see
page ).
Select this button to f ind the nearest
Acura dealer using the navigation
system. Select
this button to call the Acura dealer
you purchased your vehicle f rom.
AcuraLink also directs you to this
dealer so you can schedule a
maintenance appointment or receive
inf ormation about a message. If you
visit another dealer f or service two
times within a 14-month period,
AcuraLink will reset to call that
dealer.
Select this
button to get more inf ormation about
the current diagnostic message. To
use this option, your cell phone must
be linked to the HFL and have a
compatible data service available.
Access the Owner Link website to
f ind out which data services are
currently compatible with AcuraLink.
257
AcuraLink
Message Pref erences
Delete
Voice
Call
Call
Find Nearest Acura Dealer Call Your A cura Dealer
Diagnostic Inf o
Features
247
——
y
y
() yy

µ
µ
µ
µ Select
this button to begin the process
required to connect to Acura. This is
used to access the most recent
diagnostic information when a
problem occurs. Select
ON to have
the system automatically read each
message to you. Select OFF to
manually select the Voice button
when you want a message read to
you.
To
access the following functions,
press the SETUP button, push the
interface dial to the right to select
MORE, then rotate the interface dial
to select AcuraLink/Messages.
Select this
button to delete all stored messages
within a category, except for
diagnostic info and recall campaign
messages. These messages can only
be deleted by a certified technician
after the recall is done or the
problem is corrected, or through a
broadcast message from Acura.
Select ON if you want to be notified
of new messages (envelope icon
appears on the naviga tion screen).
Select OFF if you do not want to be
noti fied of new messages (envelope
icon does not appear on the
naviga tion screen). For
the Phone Data
Connection button to be active, you
need a Bluetooth compatible and
enabled cellphone paired to the
HandsFreeLink (HFL), and a
compatible data service (see on page ).262
AcuraLink
AcuraL ink/Message Screen
Phone-Data Connection Auto Reading
Delete Messages
New Message Notif ication
Pairing
Your Phone
248
NOTE:
——
y
y
() yy

For security purposes, newer garage
door opening systems use a ‘‘rolling’’
or variable code. Information from
the remote control and the garage
door opener are needed bef ore
HomeLink can operate the garage
door opener.Find the ‘‘training’’ button on your
garage door opener unit. The
location will vary, depending on
the manufacturer. Make sure you have properly
completed the ‘‘Training
HomeLink’’ procedure. Press the HomeLink button again
f or about 1 second. It should
operate the garage door.
The ‘‘Training HomeLink’’
procedure trains HomeLink to the
proper garage door opener code.
The f ollowing procedure
synchronizes HomeLink to the
garage door opener so it sends and
receives the correct codes. Press the training button on the
garage door opener unit until the
indicator next to the button comes
on. The indicator may blink, or
comeonandstayon.Youthen
have approximately 30 seconds to
complete the f ollowing steps.Press and hold the button on
HomeLink f or 3 to 4 seconds.
Press and hold the HomeLink
button again f or 3 to 4 seconds.
This should turn of f the training
indicator on the garage door
opener unit. (Some systems may
require you to press the button up
to three times.)
6.
2. 4.
5.
1. 3.
T raining With a Rolling Code
System
HomeL ink Universal Transceiver
Features
255
TRAINING BUTTON
——
y


y
() yy

Youshoulderaseallthreecodes
before selling the vehicl e.
Toerasethecodesstoredinallthree
buttons,
press and hold the two
outside buttons until the red
indicator begins to flash, then
release the buttons.
If you want to retrain a programmed
button for a new device, you do not
have to erase all button memory.
You can replace the existing memory
code using this procedure: If
a standard transmitter was
programmed, the indicator will
stay on for about 25 seconds.
HomeLink
is a registered
trad emark of Johnson Controls, Inc.
If
you have problems with training
the HomeLink Universal Transceiver,
or would like information on home
products that can be operated by
HomeLink, call (800) 355-3515. On
the Internet, go to
www.homelink.com. Once
the HomeLink indicator
begins to flash slowl y, continue to
hold the HomeLink button, and
f ollow steps 3 thru 6 under
‘‘Training HomeLink’’ (see page ).
If a rolling code transmitter was
previously programmed, the
indicator will f lash rapidly f or 2
seconds, and then stay on f or
about 23 seconds.
Press and hold the HomeLink
button to be trained until the
HomeLink indicator begins to
flash slowly.
1. 2.
253
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Erasing Codes
Retraining a Button Customer Assistance
HomeL ink Universal Transceiver
256
——
y

y
() y
y

ÛÝ
Turn the engine off, and confi
rm the
fuel fill cap is installed. If it is, loosen
it, then retighten it until it clicks at
least once. When you c an restart the
engine, the message appears again.
The message goes off after several
days of norm al driving once you
tighten or replace the fuel fill cap. To
scroll to another message, press the
INFO ( / ) button.
If your fuel fill cap is loose or
missing, a ‘‘TIGHTEN FUEL CAP’’
message appears on the multi-
information display after you start
the engine.
Turn the engine off, and confi
rm the
fuel fill cap is installed. If it is, loosen
it, then retighten it until it clicks at
le ast once. When you restart the
engine, the message appears again.
The message goes off after several
days of norm al driving once you
tighten or replace the fuel fill cap. To
scroll to another display, p ress the
Select/Reset knob.
If the system still detects a leak in
your vehicle’s evaporative emissions
system, the malfunction indicator
lamp (MIL) comes on. If the fuel fill
cap was not already tightened, turn
the engine off, and check or
retighten the fuel fill cap until it
clicks at least once. The MIL should
go off after several days of normal
driving once the cap is tightened or
replaced. If the MIL does not go off,
have your vehicle inspected by a
dealer. For more information, see
page .
If the system still detects a leak in
your vehicle’s evaporative emissions
system, the malfunction indicator
lamp (MIL) comes on. If the fuel fill
cap was not already tightened, turn
the engine off, and check or
retighten
the fuel fill cap until it
clicks at least once. The MIL should
go off after several days of normal
driving once the cap is tightened or
replaced. If the MIL does not go off,
have your vehicle inspected by a
dealer. For more inf ormation, see
page . 394
394
On RDX with Technology Package
modelTighten Fuel Cap Message
Service Station Procedure
Bef ore Driving
281
——
yy
() yy

ÛÝ
To display the tire pressure monitor,
press the INFO ( / ) button until
it appears on the multi-inf ormation
display.
When all tire pressures are normal,
the tire pressure monitor will show a
‘‘TIRE PRESS. OK SYSTEM FUNC
NORMAL’’ message. When any of the tires have low
pressure, the low tire pressure
indicator on the instrument panel
comes on, and the multi-inf ormation
display also interrupts the current
display and shows a ‘‘CHECK TIRE
PRESSURE’’ message. You can see
one or more of the low pressure tire
positions highlighted in the display
along with this message.When any of the tires have low
pressure, the tire pressure monitor
shows a ‘‘TIRE PRESS. ERROR
SYSTEM FUNC NORMAL’’
message.
On RDX with Technology Package
model
Tire Pressure Monitoring System (TPMS)
312
INFO BUTTONS
——
y

y
() y
y

If one or more tires have low
pressure, the low tire pressure
indicator on the instrument panel
also comes on (see page ).
It is possible that the pressures
shown on the multi-inf ormation
display and the pressures you
manually measure are slightly
dif f erent.
If the dif f erence is signif icant or you
cannot make the low tire pressure
indicator and message on the multi-
inf ormation display go out af ter
inf lating the tires to the specif ied
values, have your dealer check the
system as soon as possible.
When the TPMS is functioning
normally, you can see the tire
pressure readings of each tire in psi
(U.S. models) or kPa (Canadian
models) by pressing the SEL/
RESET button while the multi-
inf ormation display shows the tire
pressure monitor. If there is a problem with the TPMS,
the multi-information display shows
a ‘‘CHECK TPMS SYSTEM’’
message.
73
CONT INUED
On RDX with Technology Package
model On RDX with Technology Package
model
Tire Pressure Monitoring System (TPMS)
T ire Pressure ReadingsCheck T PMS System Message
Driving
313
U. S.
Canada SEL/RESET BUTTON
——
y
y
() y
y