2007 Acura RDX ECO mode

This indicator comes on for a few
seconds when you turn the ignition
switch to the ON (II) position. It
remindsyouthatitistimetotake
your vehicle in for scheduled
maintenance. The maintenance main
items and sub items will be displayed
in the information display. See page
for more information on the
maintenance minder.
This indicator goes off when your
dealer resets it after completing the
required maintenance service. This
indicator comes on when there
is a system message in the multi-
information display. Press the INFO
button on the steering wheel (see
page ) to see the message (see
page ).
This indicator comes on when the
washer fluid level is low. Add washer
fluid when you see this indicator
(see page ).
Most
of the time, this indicator
comes on along with other indicato rs
in the instrument panel such as the
seat belt reminder indicator, SRS
indicato r, VSA system indicato r, etc. Your
vehicle has a door and tailgate
open monitor on the information
display. If any door(s) or the tailgate
is not closed tightly, the appropriate
light/lights will come on to reminds
you to close the tailgate or the
door(s).
The door and tailgate open monitor
appears on the multi-inf ormation
display (see page ).
79
330
35384
86
On RDX model only
On RDX with Technology Package
model only
Canadian RDX model only On RDX with Technology Package
model only
On RDX model
Instrument Panel Indicators
Maintenance Minder
Indicator
System Message
Indicator
Washer Level IndicatorDoor and T ailgate Open Monitor
74
——
y

y
() yy

¶¶µµ
µµµ
µµµ
To reset a trip meter, display it, and
then press and hold the Select/Reset
knob until the number resets to ‘‘0.0’’.
When you reset Trip A, AVG. FUEL
A is reset at the same time. When
you reset Trip B, AVG. FUEL B is
reset.
This shows your vehicle’s average
f uel economy in mpg (U.S. models)
or
/100 km (Canadian models)
since you last reset the Trip A or
Trip B. If the outside temperature is
incorrectly displayed, you can adjust
it up 5°F in U.S. models ( 3°C in
Canadian models) warmer or cooler.
NOTE: The temperature must be
stabilized bef ore doing this
procedure.
When the temperature reaches the
desired value, release the Select/
Reset knob. You should see the new
outside temperature displayed.
The average f uel mileage will be
reset when you reset the trip meter,
or if the vehicle’s battery goes dead
or is disconnected. This shows the outside temperature
in Fahrenheit (U.S. models), or in
Centigrade (Canadian models).
The temperature sensor is in the
f ront bumper. The temperature
reading can be affected by heat
ref lection f rom the road surf ace,
engine heat, and the exhaust f rom
surrounding traf f ic. This can cause
an incorrect temperature reading
when your vehicle speed is under
19 mph (30 km/h). When you start
your trip, the sensor is not f ully
acclimatized, theref ore it may take
several minutes until the proper
temperature is displayed.
In certain weather conditions,
temperature readings near f reezing
(32°F, 0°C) could mean that ice is
f orming on the road surf ace.
To adjust the outside temperature
indicator, press and hold the Select/
Reset knob f or 10 seconds. The
f ollowing sequence will appear f or 1
secondeach:0,1,2,3,4,5, 5, 4,
3, 2, 1, 0 (U.S.) or 0, 1, 2, 3,
3, 2, 1, 0 (Canada).
CONT INUED
Gauges
AVG. FUEL A/B Out side T emperat ure Indicat or
Inst rument s and Cont rols
77
——
y

y
() yy

This shows the estimated distance
you can travel on the fuel rema ining
in the fuel tank. This distan ce is
estimated from the fuel economy
you received over the last several
miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traffic, etc.
This shows the time traveled since
you last reset it. When you turn the
ignition switch to the ON (II)
pos ition, ELAPSED TIME is reset.
You can customize the ELAPSED
TIME reset condition in the multi-
info rmation display (see page ).You
can customize the Trip A and
AVG. FUEL A reset condition in the
multi-info rmation display (see page
).
This
shows your vehicle’s average
fuel economy in mpg (U.S. model s)
or
/100 km (Canadian models)
since you last reset the Trip A or
Trip B.
When
you reset Trip A, AVG.
SPEED is also reset.
This
shows the average speed you
are traveling in miles per hour (mph)
forU.S.modelsorkilometersper
hour (km/h) for Can adian models.
When the battery is disconnect ed, or
you refuel, RANGE is also reset.
The
multi -information display in the
instrument panel shows you the
engine oil life and maintenance
service items when the ignition
switch is in the ON (II) position. This
information helps to keep you aware
of the periodic maintenance your
vehicle needs for continued trouble-
free driving. Refer to page for
more inf ormation.
This shows your current f uel
mileage.
When you turn of f the engine, INST.
MPG or INST. L/100 km is also
reset.
The average f uel mileage will be
reset when you reset the trip meter,
or if the vehicle’s battery goes dead
or is disconnected.98
100
330
Multi-Inf ormation Display
RANGE
EL A PSED T IME
AVG. FUEL A/B A VG. SPEED
Maintenance Minder
INST.MPG(U.S.models)/INST.
L /100km (Canadian models)
82
——
y
y
() yy

ÛÝÛÝ
With
the multi-information display
and the INFO ( / ) and SEL/
RESET buttons on the right side of
the steering wheel, you can
cu stomize some vehicle control
settings.
To enter the customizing mode,
press and hold the INFO ( / )
button for more than 3 seconds.
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the tran smission in
Park. You
cannot customize the settings
under these conditions:
If you turn the ignition switch to
the ACCESSORY (I) or the LOCK
(0) position.
If you move the shift lever out of
Park. If
you want the settings as they were
when the vehicle left the factory,
select DEFAULT ALL, as described
on page .
Refer to the table in the next page
about the settings you want to
customize.
The
first customizing menu is:
CHG SETTING
DEFAULT ALL If
you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button (see page ). 90
91
CONT INUED
Customized Settings
Multi-Inf ormation Display
Inst rument s and Cont rols
87
——
y
y
() yy

Î
Î
Î
Î
Î
Menu Item Page
Group Setup Setting Option
Description
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK TIMER
AUTO DOOR UNLOCK 110
112
114
116
90
DOOR SETUP
(P.107)
DEFAULT ALL DRIVER DOOR
ALL DOORS
ON
OFF
30 sec
60 sec
90 sec
DRIVER’S DOOR WITH
SHIFT TO P
ALL DOORS WITH
SHIFT TO P
DRIVER’S DOOR WITH
IGN OFF
ALL DOORS WITH IGN
OFF
OFF
SET
EXIT
Changes which doors unlock with the remote
transmitter in a first push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock and not opening the door.
Changes when the doors automatically unlock.
Changes all the customized settings as they were
the vehicle left the factory.
: Default setting
Multi-Inf ormation Display
Inst rument s and Cont rols
89
——
y

y
() yy

ÛÝÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button. To enter the customizing mode,
press and hold the INFO ( / )
button for more than 3 seconds. When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
CUSTOMIZE ENTRY.
To set the def ault settings, select
DEFAULT ALL, and press the SEL/
RESET button. Then select SET, and
press the SEL/RESET button.
Multi-Inf ormation Display
DEFAUL T AL L
90
——
yy
() yy

ÛÝ
To exit DOOR LOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, and then press the
SEL/RESET button. The screen
goes back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE MENU.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE MENU. If this
happens, you need to repeat the
same procedure.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
111
——
yy
() y

y

The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights on
reminder beeper. Wi
th the headlight switch off or in
the position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch off, even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
You can change the ‘‘HEADLIGHT
AUTO OFF TIMER’’ setting on the
multi-inf ormation display (see page
).
105
On RDX with Technology Package
model
Daytime Running L ights
Headlights
Inst rument s and Cont rols
123
——
y

y
() y
y