2007 Acura MDX Clock

Make sure the engine and radiator
are cool.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pour the coolant slowly and
caref ully so you do not spill any.
Clean up any spill immediately; it
could damage components in the
engine compartment.
Put the radiator cap back on, and
tighten it fully.
Relieve any pressure in the cooling
system by turning the radiator cap
counterclockwise, without
pressing down. Remove the radiator cap cover. Remove the radiator cap by
pushing down and turning
counterclockwise.
3. 4.
1.
2. 5.
CONT INUED
Engine Coolant
Maint enance
391
RADIATOR CAP COVER
RADIATOR CAP
——y
y
()-yy

CONTINUED
Remove the electrical connector
from the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
Remove
the front bulkhead cover
(see page ). Open the hood.
Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustment should be done by your
dealer or other qualif ied mechanic.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.
1.
2.3.
4.
386
MDX and Technology Packages models
Headlight A iming Replacing a High Beam Headlight
Bulb
L ow Beam Headlight Bulb
Replacement
Lights
Maint enance
397
BULB
CONNECTOR
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
——y
y
()-yy

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Insert
the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working.
Open the hood.
Remove the f ront bulkhead cover
(see page ).
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
1.
2.
3.
4.
5.
5.
6.
7.
6.
7.
386
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
Lights
398
BULB
BULB
SOCKET
FRONT TURN SIGNAL LIGHT
PARKING LIGHT
SOCKET
——y
y
()-yy

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Remove the two bolts, and remove
the rear light assembly f rom the
rear pillar.
Open the tailgate. Use a
screwdriver protected with a cloth
to pry open the two covers.
Determine which of the two bulbs
is burned out: turn signal/hazard
lights or side marker light.
1. 2.
3.
3.
4.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
400
CONNECTOR
INNER FENDER COVER
BOLT
BOLT
——y
y
()-yy

CONT INUED
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Install the rear light assembly in
the rear pillar. Tighten the two
bolts. Snap the bolt covers into
position.
Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
1.
4.
5. 6.
7.
8.
9.
Lights
Replacing a Back-up L ight Bulb
Maint enance
401
COVER
BULB SOCKET
——y

y
()-yy

Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working. Place the cover back into the light
assembly. Push it up until it locks
in place. Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
4.
5. 6.
2.
3. 7.
Lights
Side T urn Signal L ight
Rear L icense Plate Bulb
402
BULB
SOCKET
——y
y
()-yy

The spare tire is stored
underneath the rear cargo area.
Remove the plastic cover on the
cargo area lining to access the
shaft for the spare tire hoist.
The tools and jack are under the
cargo area behind a cover on the
driver’s side. Remove the cover by
turning the knobs
counterclockwise, then pulling out
the cover. Turn the jack’s end bracket
counterclockwise to loosen it, then
remove the jack.
5. 6. 7.
Changing a Flat Tire
420
COVER
KNOB PLASTIC COVER
——y
y
()-yy

Remove the bracket from the
spare tire. Keep turning the wheel nut
wrench to create slack in the cable.Loosen each wheel nut 1/2 turn
with the wheel nut wrench.
Put the wheel nut wrench on the
hoist shaf t. Turn the wrench
counterclockwise to lower the
spare tire to the ground. 11.
10.
8. 9.
CONT INUED
Changing a Flat Tire
T aking Care of t he Unexpect ed
421
BRACKET
WHEEL NUT WRENCH
WHEEL NUT WRENCH
The wheel nut wrench supplied with
your vehicle is specially adapted to f it
the hoist shaf t. Do not use any other
tool.
——y
y
()-yy