2007 Abarth Grande Punto lock

139
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
WHEN NEEDING TO
CHANGE A BULB
GENERAL INSTRUCTIONS
❒ When a light is not working, check that
the corresponding fuse is intact before
changing a bulb. For the location of fus-
es, refer to the paragraph “If a fuse
blows” in this section;
❒ Before changing a bulb check the con-
tacts for oxidation;
❒ Burnt bulbs must be replaced by oth-
ers of the same type and power;
❒ Always check the height of the head-
light beam after changing a bulb.
IMPORTANT The headlight inner surface
may be lightly misted over: this is not a
fault but a natural fact due to low tem-
perature and the level of air humidity. It
will disappear as soon the headlights are
turned on. The presence of drops inside
the headlights means water infiltration,
therefore contact Abarth Dealership.
TYPES OF BULBS
Various types of bulbs are fitted to your
car:
AGlass bulbs: clipped into position. Pull
to remove.BBayonet type bulbs: to remove this
type of bulb from its holder, press
the bulb and turn it counter-clock-
wise.
CTubular bulbs: release them from
their contacts to remove.
D-EHalogen bulbs: to remove the bulb,
release the clip holding the bulb in
place. Halogen bulbs must be han-
dled touching only the metal-
lic part. If the transparent bulb
is touched with the fingers, its
lighting intensity is reduced and life of
the bulb may be compromised. If
touched accidentally, rub the bulb with
a cloth moistened with alcohol and al-
low to dry.
Modifications or repairs to
the electrical system (elec-
tronic control units) carried out in-
correctly and without bearing the fea-
tures of the system in mind can cause
malfunctions with the risk of fire.
WARNING
Halogen bulbs contain pres-
surised gas which, if broken,
may cause small fragments of glass to
be projected outwards.
WARNING
fig. 10F0M0207m

141
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IF AN EXTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT LIGHT UNITS fig. 11
The front light units contain sidelights,
dipped beam, main beam and direction in-
dicator bulbs.
The bulbs are arranged inside the light unit
as follows:
Asidelights
Bdipped beams/main beams (double
light)
Cdirection indicatorsSIDELIGHTS fig. 12
To change the bulb, proceed as follows:
❒remove the snap-fitted rubber cap A,
as shown by the arrow;
❒press tabs Band remove the bulb hold-
er;
❒remove the bulb Cand replace it;
❒refit the bulb holder and refit the cap
A, check for proper locking.
fig. 11F0M0178mfig. 12F0M0179m

142
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
DIPPED BEAM/ MAIN BEAM
HEADLIGHTS fig. 13
To change the bulb, proceed as follows:
❒remove the snap-fitted rubber cap A,
as shown by the arrow;
❒disconnect the central electric connec-
tor and release the bulb holder catch;
❒remove the bulb Band replace it;
❒fit the new bulb, making the outlines of
the metallic part coincide with the
grooves on the reflector;
❒refit the bulb holder catch and reconnect
the electrical connector;
❒refit the cap Alocking it properly.DIRECTION INDICATORS
Front fig. 14-15
To change the bulb, proceed as follows:
❒steer the right/left wheel outwards;
❒turn the catch A-fig. 14as shown by
the arrow, then use the lid B;
❒remove the cover/bulb holder C-
fig. 15turning counterclockwise;
❒remove the bulb Dpushing it gently and
turning counterclockwise (“bayonet”
clamping), then replace it;
❒refit the cover/bulb holder Cby turn-
ing it clockwise and locking it proper-
ly;
❒close the lid B-fig. 14the turn the
catch A.
fig. 13F0M0180mfig. 14F0M0261mfig. 15F0M0181m

143
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
Side fig. 16
To change the bulb, proceed as follows:
❒work on the lens Ato compress the in-
ternal catch B, then pull the unit out-
wards;
❒turn the bulb holder C counterclock-
wise, remove the snap-fitted bulb D
and replace it;
❒refit the bulb holder Cin the lens by
turning it clockwise;
❒refit the unit making sure the catch
clicks into place B.FRONT FOG LIGHTS
(where provided)
Contact Abarth Dealership to have front
fog lights A-fig. 17replaced.
REAR LIGHT UNITS fig. 18-19
Rear light units contain taillights, brake
light and direction indicators bulbs.
The bulbs are arranged inside the light unit
as follows:
Bdirection indicators
Ctaillights
Dtaillights/brake light (double light).
fig. 16F0M0182m
fig. 18F0M0184m
fig. 17F0M041Ab

144
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
To change the bulb proceed as follows:
❒open the tailgate then, slacken the two
fastening screws A;
❒disconnect the central electric connec-
tor and pull the lens unit outwards;
❒slacken the screws Eand remove the
bulb holder;
❒remove the bulb to replace B, Cor D
pushing it slightly and turning it coun-
terclockwise (“bayonet” clamping) and
replace it;
❒refit the bulb holder and tighten the
screws E;
❒reconnect the electric connector, suit-
ably refit the unit to the car body and
then tighten the fastening screws A.
fig. 20F0M0208m
fig. 19F0M0185m
REAR FOG LIGHTS fig. 20
Contact Abarth Dealership to have rear
fog lights Areplaced.

146
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
IF AN INTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT CEILING LIGHT
To replace the bulbs proceed as follows:
❒work in the points shown by the ar-
rows and remove light A-fig. 26
❒open the protection lid B;❒change the bulb fig. 25releasing it from
the side contacts and making sure the
new bulb is correctly fastened between
the contacts;
❒refit the snap-fitted lens unit.
fig. 26F0M0213m
fig. 27F0M0234m
fig. 25F0M0233m
❒replace bulbs C-fig. 27releasing them
from the side contacts; make sure that
new bulbs are correctly clamped be-
tween contacts;
❒re-close the lid B-fig. 27and secure light
A-fig. 26into its housing locking it
properly.

147
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
BOOT LIGHT fig. 28
To change the bulb, proceed as follows:
❒ open the tailgate;
❒remove the light Alevering in the point
shown by the arrow;
❒open the protection Band replace the
snap-fitted bulb;
❒re-close the protective cover Bon the
lens;
❒refit the light Ainserting it in its cor-
rect position firstly on one end and
then on the other until it clicks into
place.PUDDLE LIGHTS
(for versions/markets,
where provided) fig. 29-30
To change the bulb, proceed as follows:
❒remove the light by pressing clip Awith
a screwdriver;
❒press the bulb protection cover sides
Bon the two fastening pins and turn it;
❒replace the snap-fitted bulb C;
fig. 28F0M0216mfig. 29F0M0217mfig. 30F0M0229m
❒refit bulb protection cover fitting the
two fastening pins;
❒refit the ceiling light inserting first end
Dand then pressing the other end un-
til hearing the locking click of the clip.

152
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IINDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
7.5
7.5
5
5
10
5
20
20
20
20 1
8
13
2
5
11
4
6
14
7
FUSE SUMMARY TABLE
Fuse box on dashboard fig. 33
USERSFUSE AMPERE
Right dipped headlamp
Left dipped headlamp, headlamp alignment corrector
INT/A power supply for relay coils in engine fuse junction unit and relay coils in
body computer control unit
Front courtesy light, lights in visors, luggage compartment light
+ battery power supply for EOBD diagnostic socket, automatic climate control
system control unit, alarm siren, car radio, convergence control unit, tyre
monitoring control unit
INT power supply for instrument panel, switch on brake pedal (N.O. contact),
third brake light
Door locking/unlocking motors, dead lock activation motors, tailgate unlocking motor
Windscreen/rearscreen washer pump
Electric window motor on driver’s front door
Electric window motor on passenger side front door