2007.5 PEUGEOT 4007 handbrake
[x] Cancel search: handbrakePage 6 of 221
FAMILIARISATION
9
INSTRUMENTS AND CONTROLS
1. A u d i o e q u i p m e n t c o n t r o l s .
2. T e l e p h o n e c o n t r o l s .
3. S t e e r i n g w h e e l a d j u s t m e n t c o n t r o l .
4. F r o n t a n d r e a r w i p e r s / w a s h - w i p e
control.
5. I n s t r u m e n t p a n e l .
6. Driver's air bag.
Horn.
7. C r u i s e c o n t r o l s w i t c h e s .
8. Gear lever.
9. Handbrake.
10. Bonnet release.
11. E n c l o s e d s t o r a g e c o m p a r t m e n t .
12. H e a d l a m p h e i g h t a d j u s t m e n t .
Deactivation of the ASC system.
D e a c t i v a t i o n o f t h e a u d i b l e p a r k i n g assistance.
13. C u p h o l d e r .
14. S i d e a d j u s t a b l e a n d c l o s i n g v e n t .
15. Information button.
16. W i n d o w d e - i c i n g a n d d e m i s t i n g
vent.
17. W i n d s c r e e n d e - i c i n g v e n t .
Page 18 of 221
1
INSTRUMENTS and CONTROLS
Indicator lights is on Cause Observations
Diesel
pre-heating Fixed This comes on when
the ignition switch is at
ON. Wait until this light has switched off before
starting.
The duration for which this is displayed is
determined by the exterior climatic conditions.
Warning lights is on Cause Observations
Handbrake/
B r a k e fl u i d l e v e l Fixed This comes on for a
few seconds when the
ignition is turned to
"ON" then switches off.
It is accompanied by a message on the
instrument panel display.
The handbrake is
applied or has not been
released fully. It is accompanied by a message on the
instrument panel display. Release the
handbrak²e to switch off the warning light.
T h e b r a k e fl u i d l e v e l i s
too low. It is accompanied by a message on the
i n s t r u m e n t p a n e l d i s p l a y . T o p u p w i t h b r a k e fl u i d
and contact a PEUGEOT dealer.
Emission
control system Fixed or
fl a s h i n g This comes on or
fl a s h e s i f t h e s y s t e m
fails. Contact a PEUGEOT dealer without delay.
It should switch off a few seconds after starting
the engine.
Battery charge Fixed This comes on if a
charging circuit fault
occurs. It should switch off when the engine is started.
It is accompanied by a message on the
instrument panel display. Check the battery
terminals (refer to the "Battery" section).
Page 21 of 221
1
INSTRUMENTS and CONTROLS
Warning messages (ignition at "ON")
Message is on
Associated
w a r n i n g l i g h t
Cause Solution - action Observations
ABS Fixed Anti-lock braking
system (ABS)
fault. Contact a PEUGEOT
dealer.
The vehicle retains
conventional braking
without assistance but
you are advised to stop.
Braking
system Fixed and The level of
b r a k e fl u i d i n t h e
reservoir is too
low.
Stop and top up,
otherwise contact a
PEUGEOT dealer. If the message
remains on after
topping up, contact a
PEUGEOT dealer.
Braking system
fault. Contact a PEUGEOT
dealer.
It is essential to
s t o p .
Handbrake on Fixed You have moved
off with the
handbrake still
applied. Release the handbrake.
Coolant
temperature Flashing
(slow)
- High engine
temperature. If the message
fl a s h e s
s l o w l y , wait for the
engine to cool before
topping up the level, if
necessary.
It is essential to
s t o p y o u r v e h i c l e i n
a s a f e p l a c e .
Flashing (rapid) If the message
fl a s h e s
r a p i d l y , contact a
PEUGEOT dealer
without delay.
Seat belt Fixed The driver has
not fastened or
has unfastened
his seat belt. Fasten your seat belt. An intermittent
audible signal is
heard above 5 mph
(8 km/h).
Page 32 of 221
1
i
i
INSTRUMENTS and CONTROLS
When the vehicle is
s t a t i o n a r y , it allows the
user to change the fol-
lowing parameters:
- the choice of the reini- tialisation of the aver-
age consumption and
average speed,
- the fuel consumption unit,
- the temperature display unit,
- the display language,
- activation/deactivation of the INFO
button sound,
- the break (rest) reminder display in- terval,
-
restore the manufacturer’s parameters.
FUNCTION PARAMETERS FUNCTION PARAMETERS
System which provides access to cer-
tain function parameters.
In order to change the settings, it
is essential that you stop the ve-
hicle and switch on the ignition.
Apply the handbrake and place
the gear lever in neutral.
When the vehicle is moving ,
the functions setting display is
not displayed when you press
the INFO button.
With the ignition on , press the INFO
button on the fascia, to the right of the
instrument panel, several times in suc-
cession until the "SETTING MENU"
screen is displayed. O p e r a t i o n
press and hold the INFO button for
a few seconds to display the menus
screen. Press and hold the
INFO button
for a few seconds to return to
the previous screen.
When the menus screen is dis-
played, if no operation is carried
out within 15 seconds, the func-
tion parameters screen is dis-
played.
on the menus screen, press the
INFO button to select a function
from the list:
MENU
1/2
:
- 1 - 2 (choice of the reinitialisation of
the average consumption and aver-
age speed),
- UNIT (choice of the fuel consump-
tion units),
- choice of the t e m p e r a t u r e d i s p l a y
unit ,
- LANGUAGE (choice of the display
language),
MENU
2 / 2 :
- a/b (choice of displaying a different
language on the instrument panel
display and the navigation display),
- a c t i v a t i o n / d e a c t i v a t i o n o f t h e
INFO button sound ,
- ALERT (changing of the "BREAK
ADVISED" break reminder display
interval),
- REINITIALISE (restore the manu-
facturer’s parameters). C h o i c e o f t h e r e i n i t i a l i s a t i o n o f
t h e a v e r a g e c o n s u m p t i o n a n d
a v e r a g e s p e e d
You can choose between two average
consumption and average speed reini-
tialisation modes:
- automatic reinitialisation
(choice 1) ,
- manual reinitialisation (choice 2) .
On the menus screen:
press the INFO button to select:
press and hold the INFO button for a
few seconds to switch in succession
from reinitialisation mode 1
(automatic)
to reinitialisation mode 2 (manual) .
T h e m o d e s e l e c t e d i s c o n fi r m e d .
Page 119 of 221
7
DRIVING
HANDBRAKE HANDBRAKE
Mechanical brake to hold the vehicle
when stationary.
Releasing
Pull on the handle and press the
button A to release the handbrake.
Applying
Pull the handbrake to immobilise
your vehicle.
When parking on a slope, direct your
wheels towards the pavement and ap-
ply the handbrake.
6 - SPEED MANUAL GEARBOX 6 - SPEED MANUAL GEARBOX
Reverse
To change to reverse gear, lift the ring
under the gear lever knob and push the
gear lever to the left then to the front.
Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.
When the vehicle is being
driven, the displaying of this
screen indicates that the
handbrake is still on or has
not been properly released.
Page 132 of 221
8
CHECKSCHECKS
Manual gearbox Refer to the servicing booklet
for details of gearbox mainte-
nance.
Brake pads Brake wear depends on the
style of driving, particularly in
the case of vehicles used in
town, over short distances. It
may be necessary to have the
condition of the brakes checked, even
between vehicle services.
Unless there is a leak on the circuit, a
d r o p i n t h e b r a k e fl u i d l e v e l i n d i c a t e s
that the brake pads are worn. Brake disc wear status
For any information relating to
checking of the brake disc wear
status, contact a PEUGEOT
dealer.
Handbrake If the handbrake travel is too
long or if you notice a loss
of effectiveness of this sys-
tem, the handbrake must be
adjusted, even between two
services.
This system must be checked by a
PEUGEOT dealer.
Only use products recommended by
PEUGEOT or products of equivalent
q u a l i t y a n d s p e c i fi c a t i o n s . In order to optimise the opera-
tion of units as important as
the braking system, PEUGEOT
s e l e c t s a n d o f f e r s v e r y s p e c i fi c
products.
To avoid damaging the electrical
units, the use of a high pressure
washer in the engine compart-
ment is strictly prohibited.
Transfer box and rear
differential.
Refer to the servicing booklet
for details of the service inter-
val for these components.
Page 135 of 221
9
i
PRACTICAL INFORMATION
Parking the vehicle
Immobilise the vehicle where it
d o e s n o t b l o c k t r a f fi c : i f p o s s i b l e ,
park the vehicle on level, stable
and non-slippery ground.
Apply the handbrake, switch
o f f t h e i g n i t i o n a n d e n g a g e fi r s t
gear to lock the wheels.
If necessary, place a chock un-
der the wheel diagonally oppo-
site the wheel to be changed.
Never go underneath a vehicle
raisedusing a jack; use a stand.
Removing the wheel
List of operations
Fit the anti-theft socket 5 on the
wheelbrace 1 to unlock the anti-theft
bolt.
Unlock the other bolts using the
wheelbrace 1 only.
Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underframe, which-
ever is closest to the wheel to be
changed.
E x t e n d t h e j a c k 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.
R a i s e t h e v e h i c l e u n t i l t h e r e i s s u f fi -
cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.
Remove the bolts and store them in
a clean place.
Remove the wheel.
Page 215 of 221
11
i
AUDIO EQUIPMENT and TELEMATICSEQUIPMENT and TELEMA
Changing the language,
programming the voice
Changing the language of the voice
commands
By default, the recognition system is in
English. Programming the user’s voice
You can use the user’s voice program-
ming function to create a voice model
for one person per language.
The characteristics of your voice and
your pronunciation are recorded in this
model for improved voice recognition.
It is essential that the vehicle is parked
in a safe place, with the handbrake ap-
plied.
Switch off your telephone during the
process to avoid any interruption.
1 - Press the SPEAK button. 5 - T h e s y s t e m s a y s t h e fi r s t o f 4 5 t y p i -
cal phrases.
If you do not start the program-
ming process within approxi-
mately 3 minutes after pressing
the SPEAK button, the process
is cancelled.
If you press the SPEAK button
within 5 seconds following the
reading of a voice command,
the recording of this command
is repeated.
1 - Press the SPEAK button.
2 - Say "Setup".
3 - Say "Language".
4 - The system says "Select a lan- guage: English, Spanish, French,
German or Italian".
5 - Say the language of your choice in English, example:
say "French" for French.
6 - The system then says "French selected. Is this correct?"
7 - Say "Yes" to start the change of language process or say
"No" to return to steps 4 to 7.
8 - The system repeats the language chosen and completes the change
of language process. 2 - Say "Word training".
3 - An explanation message is given.
4 - When you are ready to start, press and hold the SPEAK
button. 6 - Repeat each phrase in the
table on the next page.
The system records your voice and
moves on to the recording of the next
command.
Continue the process until all of the
phrases have been recorded.
7 - After reading all the voice com- mands, the system says "The word
enrolment is complete" and ends
the process.