2007.5 Peugeot 307 cruise control
[x] Cancel search: cruise controlPage 25 of 212
INSTRUMENTS and CONTROLS
24
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er’s driving habits. DISPLAY
In the event of under-revving or over-
r e v v i n g , t h e g e a r s e l e c t e d l a s h e s f o r
a few seconds, then the actual gear
engaged is displayed
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is select-
ed.
A u t o m a t i c g e a r b o x i n d i c a t o r
l i g h t s
"SNOW" indicator light This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
Page 28 of 212
INSTRUMENTS and CONTROLS
27
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
T r i p r e c o r d e r z e r o r e s e t
b u t t o n
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
L i g h t i n g r h e o s t a t
Page 116 of 212
DRIVING
103
This cruise control, of the new
generation, is linked with the speed
limiter. It has a display on the
instrument panel to indicate the
memorised reference speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
In order for it to be memorised or
activated, the vehicle speed must be
greater than 25 mph (40 km/h) with at
least fourth gear engaged for vehicles
i t t e d w i t h a m a n u a l g e a r b o x .
O n v e h i c l e s i t t e d w i t h a n a u t o m a t i c
gearbox, the lever must be in
position D , or in at least second gear
in sequential mode. When the cruise control function
is activated, pressing this button
enables you to display the distance
recorders.
After a few seconds or when this
button is pressed again, the display
returns to the cruise control function. First activation/memorising a
reference speed
As soon as you reach the chosen
speed, press button
2 or 3 . This
memorises the speed and the display
indicates (e.g. at 70 mph (110 km/h)):
Selecting the function
Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates:
Note: It is possible to accelerate
and drive momentarily at a speed
greater than the memorised speed.
T h e v a l u e m e m o r i s e d l a s h e s . W h e n
the accelerator pedal is released, the
vehicle will return to the memorised
speed.
Cancelling the cruise control
If you wish to cancel the cruise
control:
Press button 4 or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
(110 km/h)):
CRUISE CONTROL * Instrument panel display
* According to country.
Page 117 of 212
DRIVING
104
Cancelling the memorised
reference speed
When the vehicle becomes
stationary, after switching off the
ignition, the system no longer
memorises a speed.
Contact a PEUGEOT dealer to have
the system checked. When changing the memo-
rised reference speed by
means of a maintained press,
pay attention as the speed
can increase or decrease rapidly.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f i c .
In the event of a steep slope,
the cruise control cannot prevent
the vehicle from exceeding the
programmed speed.
In any event, the cruise control cannot
replace the need to comply with
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r i t o n e m a t o n t o p o f another.
Reactivating the cruise control
After cancellation of the cruise
control,
press button 4 . Your vehicle
will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)):
Changing the memorised
reference speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
A brief press increases by 1 mph
(1 km/h).
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 . Switching the function off
Place dial 1 in position 0 to switch
the system off.
Operating fault
In the event of a cruise control
malfunction, the memorised speed
i s e r a s e d , t h e d a s h e s l a s h f o r a f e w
seconds:
To memorise a speed lower than the
previous one:
press button 2 ; A brief press decreases by 1 mph (1 km/h). An extended press decreases by 5 mph
(5 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).
Page 118 of 212
DRIVING
105
This cruise control has a display on
the instrument panel to indicate the
memorised reference speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
In order for it to be memorised or
activated, the vehicle speed must be
greater than 25 mph (40 km/h) with at
least fourth gear engaged for vehicles
i t t e d w i t h a m a n u a l g e a r b o x .
O n v e h i c l e s i t t e d w i t h a n a u t o m a t i c
gearbox, the lever must be in position
D or at least second gear must be
engaged in sequential driving mode. When the cruise control function
is activated, pressing this button
enables you to display the distance
recorder.
After a few seconds or when this
button is pressed again, the display
returns to the cruise control function. First activation/memorising a
reference speed
As soon as you reach the chosen
speed, press button
2 or 3 . This
memorises the speed and the display
indicates (e.g. at 70 mph (110 km/h)):
Selecting the function
Place switch 1 in the ON
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates:
Note: It is possible to accelerate
and drive momentarily at a speed
greater than the memorised speed.
T h e v a l u e m e m o r i s e d l a s h e s . W h e n
the accelerator pedal is released, the
vehicle will return to the memorised
speed.
Cancelling the cruise control
If you wish to cancel the cruise
control:
Press button 4 or the brake or
clutch pedal.
The display indicates (e.g. at 70 mph
(110 km/h)):
* According to country.
Instrument panel display CRUISE CONTROL *
Page 119 of 212
DRIVING
106
Reactivating the cruise control
After cancellation of the cruise
control, press button 4 . Your vehicle
will return to the last memorised
speed. The display indicates (e.g. at
70 mph (110 km/h)):
Cancelling the memorised
reference speed
When the vehicle is stationary,
after the ignition has been
switched off, the system no longer
stores any speed.
Changing the memorised
reference speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
press button 3 ;
A brief press increases by 1 mph
(1 km/h).
An extended press increases by
5 mph (5 km/h).
A maintained press increases in
steps of 5 mph (5 km/h).
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 . Switching the function off
Place dial 1 in the OFF position to
switch the system off.
Operating fault
In the event of a cruise control
malfunction, the memorised speed
i s e r a s e d , t h e d a s h e s l a s h f o r a f e w
seconds:
Contact a PEUGEOT dealer to have
the system checked. When changing the memo-
rised reference speed by
means of a maintained press,
pay attention as the speed
can increase or decrease rapidly.
Do not use the cruise control on
s l i p p e r y r o a d s o r i n h e a v y t r a f i c .
In the event of a steep slope,
the cruise control cannot prevent
the vehicle from exceeding the
programmed speed.
In any event, the cruise control
cannot replace the need to observe
the speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To avoid any risk of jamming of the
pedals:
- ensure that the mat is positioned correctly.
- n e v e r i t o n e m a t o n t o p o f another. To memorise a speed lower than the
previous one:
press button 2 ;
A brief press decreases by 1 mph (1 km/h).
An extended press decreases by 5 mph
(5 km/h).
A maintained press decreases in steps
of 5 mph (5 km/h).