2007.5 Peugeot 207 Dag lights

!
135
Changing the third brake
light bulbs (4 bulbs W 5 W)

 Press on the i xing pins on each side
of the light.

 Take out the light from the outside.

 Turn the bulb holder which corre-
sponds to the faulty bulb one quar-
ter of a turn and remove it.

 Pull the bulb and change it. Changing the number plate light
bulbs (W 5 W)

 Insert a thin screwdriver in one of
the exterior holes of the lens.

 Push it towards the outside to unclip it.

 Remove the lens.

 Pull the bulb and change it.
To rei t, carry out these operations in re-
verse order.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

i
136
Rear lights (SW)
1. Brake lights (P 21 W).
2. Side lights (R 5 W).
3. Direction indicators (PY 21 W amber).
4. Fog lamps (P 21 W).
5. Reversing lights (P 21 W). Changing bulbs
These i ve bulbs are changed from out-
side the boot:

 remove the access l ap,

 disconnect the light connector,

 remove the light i xing bolt,

 take out the light from the outside,

 press on the four tabs and remove
the bulb holder,

 turn the bulb a quarter of a turn and
change it.
To rei t, carry out these operations in re-
verse order.
Take care to engage the light in its
guides keeping it in the centreline of the
vehicle.
Tighten the i xing bolt sufi ciently by hand
to guarantee the sealing of the light.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specii cation
and colour.
1. Brake lights (P 21 W).
2. Side lights (R 5 W).
3. Direction indicators
(PY 21 W amber).
4. Fog lamps (P 21 W).
5. Reversing lights (P 21 W).

!
137
Changing the third brake light
bulbs (4 bulbs W 5 W)

 Remove the two light i xing nuts.

 Take out the light from the outside.

 Press on the two tabs and remove
the bulb holder.

 Pull the bulb and change it.
To rei t, carry out these operations in re-
verse order.
Tighten the i xing bolt sufi ciently by hand
to guarantee the sealing of the light. Changing the number plate
bulbs (W 5 W)

 Insert a thin screwdriver into one of
the exterior holes of the lens.

 Push it towards the outside to unclip it.

 Remove the lens.

 Pull the bulb and change it.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

139
Fascia fuses
The fuse box is placed in the lower part
of the fascia (left-hand side).
Access to the fuses

 refer to the "Access to the tools"
paragraph. Fuse tables

Fuse N° Rating Functions

G39 20 A Hi-Fi amplii er.

G40 20 A Driver and passenger heated seats.

Fuse N° Rating Functions

F1 15 A Rear wiper.

F2 - Not used.

F3 5 A Air bags and pre-tensioners control unit.

F4 10 A
Clutch pedal switch, diagnostic socket, electrochro
matic
interior mirror, air conditioning, steering wheel a ngle
sensor, particle emission i lter pump (Diesel).

F5 30 A Electric windows, rear one-touch electric windows,
sunroof, panoramic roof shutter (SW).

F6 30 A Front one-touch electric windows, folding mirrors
supply.

F7 5 A Front and rear courtesy lights, map reading lights,
sun visor lighting, glove box lighting, clock.

140

Fuse N° Rating Functions

F8 20 A Audio equipment, audio/telephone, CD changer,
multifunction display, clock, steering wheel
controls, tyre under-inl ation detection, trailer fuse
box.

F9 30 A Front 12 V socket, rear 12 V socket (SW).

F10 15 A Alarm siren, alarm control unit, directional he adlamps.

F11 15 A
Diagnostic socket, low current ignition switch, aut
omatic
gearbox control unit.

F12 15 A Rain / brightness sensor, amplii er, trailer fuse box,
driving school module.

F13 5 A Engine fuse box, ABS relay, dual-function brake
switch.

F14 15 A Instrument panel, seat belt warning lights bar,
headlamp adjustment, air conditioning, hands-free
kit, rear parking assistance control unit, air bags.

F15 30 A Locking and deadlocking.

F17 40 A Rear screen and exterior mirrors de-icing.

SH - PARC shunt.

!
i
145
A l at battery prevents the engine
from starting (refer to the corre-
sponding paragraph).
If the telephone is being used at
this time:
- it will be maintained for 5 minutes with the RD4 audio equipment
hands-free kit,
- it will still be possible to i nish the call with the RT4 GPS au-
dio/telephone.
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
sufi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
headlamps, courtesy lights, etc. for a
maximum combined duration of thirty
minutes. Exiting economy mode
These functions are reactivated auto-
matically next time the vehicle is driven.

 In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this period
will always be between i ve and thirty
minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-function
display indicating that the vehicle has
switched to economy mode and the ac-
tive functions are put on standby.
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.

Removing a front or rear wiper blade

 Raise the corresponding wiper arm.

 Unclip the wiper blade and remove it.
Fitting a front or rear wiper blade

 At the front, check the size of the
wiper blade as the shorter blade is
i tted on the right-hand side of the
vehicle.

 Put the corresponding new wiper
blade in place and clip it.

 Fold down the wiper arm carefully.

!i
146
TOWING THE VEHICLE
Procedure for having your vehicle towed
or for towing another vehicle using a re-
movable towing eye.
Access to the tools Towing your vehicle

 On the front bumper, unclip the cov-
er by pressing at the bottom.

 Screw the towing eye in fully.

 Install the towbar.

 Switch on the hazard warning lights
on the towed vehicle.
 On the rear bumper, unclip the cover
by pressing at the bottom.

 Screw the towing eye in fully.

 Install the towbar.

 Switch on the hazard warning lights
on the towed vehicle.
Towing another vehicle
The towing eye is installed in the boot
under the l oor.
To gain access to it:

 open the boot,

 raise the l oor,

 secure it by hooking its cord on the
hook on the shelf support,

 remove the towing eye from the
holder. When towing with all four wheels on
the ground, always use a towbar.
When towing with only two wheels
on the ground, always use profes-
sional lifting equipment.
When towing with the engine off,
there is no longer any braking or
steering assistance.

 Place the gear lever in neutral
(position N on the automatic
gearbox).
Failure to comply with this special
requirement may result in damage
to certain braking components and
the absence of braking assistance
the next time the engine is started.

i
i
147
TOWING A TRAILER,
A CARAVAN, ETC.
Your vehicle is primarily designed for
transporting people and luggage, but it
may also be used for towing a trailer. Driving advice
The maximum towing load on a long
slope depends on the gradient and the
outside temperature.
In all cases, pay attention to the coolant
temperature.
Distribution of loads

 Distribute the load in the trailer so
that the heaviest items are as close
as possible to the axle and the nose
weight approaches the maximum
permitted without exceeding it.
Air density decreases with altitude, thus
reducing engine performance. Above
1 000 metres, the maximum towing load
must be reduced by 10 % and so on for
every 1 000 metres of altitude.
Refer to the "Technical Data" section for
details of the weights and towing loads
which apply to your vehicle.
Side wind

 Take into account the increased
sensitivity to side wind. Braking
Towing a trailer increases the braking
distance.
Tyres

 Check the tyre pressures of the tow-
ing vehicle and of the trailer, observ-
ing the recommended pressures.
Lights

 Check the electrical signalling on
the trailer.
The rear parking assistance will be
deactivated automatically if a gen-
uine PEUGEOT towbar is used.
 If the warning light and the

STOP warning light come
on, stop the vehicle and
switch off the engine as
soon as possible.
Towbar suited to the attachment of a
trailer or caravan with additional signal-
ling and lighting.
Cooling
Towing a trailer on a slope increases
the temperature of the coolant.
As the fan is electrically controlled, its
cooling capacity is not dependent on
the engine speed.

 To lower the engine speed, reduce
your speed.
We recommend the use of original
PEUGEOT towbars and their har-
nesses that have been tested and ap-
proved from the design stage of your
vehicle and that the i tting of the towbar
is entrusted to a PEUGEOT dealer.
If the trailer is not i tted by a
PEUGEOT dealer, it is imperative
that it is i tted using the electrical
pre-equipment installed at the rear of
the vehicle, in accordance with the
manufacturer's instructions. Driving with a trailer subjects the towing
vehicle to more signii cant stress and its
driver must be particularly careful.