2007.5 Citroen C5 maintenance

II
1919
A
IN BRIEF
M O N I T O R I N G
Tyre defl ation detection
This function allows you to display the log of alerts.
Press on button A. The following messages appear consecutively on the instrument panel screen:Tyre pressure check.
Maintenance indicator reminder.
Display of message alerts.Oil level check.

30
II
G
C
F
ADBE
I N S T R U M E N T P A N E L
A Fuel gaugeB Indicator:Coolant temperature
Cruise control/Speed limiter informationC Speed indicatorD Rev counterE Indicator:Engine oil temperature
Gear selector position and gear engaged (Auto-matic gearbox)
F Controls:Lighting rheostat
Resetting to zero of trip mileage computer and maintenance indicator

43
II
A
2121
I N S T R U M E N T P A N E L
Engine oil temperature gauge
Under normal operating condi-tions, the bars should be within section 1.
In severe operating conditions, the bars may extend into section 2.
In this event, slow down, and if nec-essary, stop the engine and check the levels (see chapter - Mainte-nance - “Levels”).
Fuel gauge
On horizontal ground, the lighting of the fuel low warning lamp warns you that you are using the reserve tank.
A message alert is displayed on the instrument panel.
Coolant temperature indica-tor
Under normal operating condi-tions, the bars should be within section 1.
In severe operating conditions, the bars may extend into section 2, the engine coolant temperature warn-ing lamp A and the STOP warning lamp will light up, stop immedi-ately.Switch off the ignition. The cooling fan may continue to operate for a certain time. Allow the engine to cool down while tak-ing the precautions indicated in chapter - Maintenace - “Levels”.
Contact a CITROËN dealer.
If the SERVICE warning lamp lights up, check the levels (see chapter - Maintenance - “Levels”).

35
II
A
B
C
Range
This is the distance that can still be travelled on the amount of fuel remain-ing in the tank.
When the range is lower than 30 km (19 miles), only four dashes are dis-played.
Instantaneous consumption
This is the result from the consumption recorded within the last 2 seconds. This function is only available when travelling at over 30 km/h (19 mph).
Instantaneous information
OPERATION
The trip computer is displayed on the instrument panel screen. I t gives you access to:2 types of instantaneous information:
Range.Instantaneous consumption.This information can be displayed in zone B of the instrument panel screen when you switch the ignition on, immediately after the display of oil level and/or maintenance information.The different information to be displayed is selected by rotating the con-trol knob A.
3 types of information for two journeys 1 and 2:
Average speed.Average consumption.The distance travelled.This information is displayed in zone C of the instrument panel by rotat-ing the control knob A.

38
II
A
I N S T R U M E N T P A N E L
C H E C K S / O I L L E V E L
Engine oil level indicator
When you switch the ignition on, the engine oil check is displayed for a few seconds on the instrument panel screen.Note: to ensure that this measurement is accurate, check the oil level o n horizontal ground after the engine has been switched off for at least 15 min-utes. An incorrect engine oil level can seriously damage your engi ne.
“Oil level incorrect” indicates that the oil level is too low.
Check using the manual dipstick. See “Lev-els”.
If, after topping up, the message re-appears, contact a CITROËN dealer.If, after topping up, the message topping up, the
“Oil level invalid” indicates a malfunctioning of the indicator.
Contact a CITROËN dealer.
“Oil level correct” indicates normal operating.
Log of alerts
This function allows you to display the log of alerts.
Press on button A. The following messages appear consecutively on the instrument panel screen:Tyre pressure check.
Maintenance indicator reminder.Display of message alerts.
Oil level check.

39
II
Maintenance indicator
It informs you when the next routine service is due in accordance with the vehicle servicing schedule in the Main-tenance Guide. This information is dependent on two parameters: the mileage covered, and the time elapsed since the last visit
Functioning if the distance to the next service is less than 3000 km
When switching on the ignition, a message is displayed on the instrument panel screen for a few seconds. It indicates to you the remaining distance before the next service.
Example: there remain up to the next service: 1900 km.
A few seconds after the ignition is switched on, the message disap-pears.
Functioning if the distance to the next service is less than 1000 km
When switching on the ignition, a message is displayed on the instrument panel screen for a few seconds. It indicates to you the remaining distance before the next service.
Example: there remain up to the next service: 500 km. When switch-ing on the ignition, a message is displayed on the instrument panel screen for a few seconds:
A few seconds after the ignition is switched on, the message disap-pears, then the maintenance sym-bol (spanner) remains lit.
Operation if the service inter-val has been passed
When switching on the ignition, a message is displayed on the instrument panel screen for a few seconds. It indicates to you that the service interval has been exceeded.
The routine service on your vehi-cle needs to be carried as soon as possible.
A few seconds after the ignition is switched on, the message disap-pears, then the maintenance sym-bol (spanner) remains lit.
I N S T R U M E N T P A N E L
M A I N T E N A N C E I N D I C A T O R

40
II
A
Resetting to zero of the maintenance indicator
If you are carrying out the service yourself, the procedure for resetting to zero is as follows:Swicth off the ignition, then move the key to position S, anti-theft.
Press on button A and keep it pressed.Switch on the ignition. The instrument panel screen counts down from 10 to 0 and displays the maintenance symbol.
Hold down button A until the zero appears and the maintenance symbol disappears.Switch off the ignition.

52
II
W I P E R S
Screen wash
Pull the screen wipe control stalk towards you.
The screen wash is accompanied by a timed wipe sequence. If the dipped beams are on, it is also accompanied by a timed headlamp wash.
Check that the wipers can operate freely in freezing temperatures.
Remove any accumulation of snow at the base of the windsc reen.
Changing the wiper blades
If changing the wiper blades, they must be stopped in the maintenance posi-tion. For this, switch off the ignition and then within one minute move the wiper control stalk. The wipers stand up vertically.
After replacement, switch on the ignition and move the wiper control stalk so that the wipers resume their normal position.
Remark: The maintenance position can also be used in snowy conditio ns to avoid a build up of snow.