2007.5 Citroen C2 DAG wheel
[x] Cancel search: wheelPage 58 of 191
-+
5 9
II
E L E C T R O N I C G E A R B O X S Y S T E M
M A N U A L M O D E
Gear controls under the steer-ing wheel
Place the gear lever in position M, and then the controls under the steering wheel will give you access t o t h e fi v e g e a r s i n f o r w a r d d r i v e .
To change gear:Pull the control “+” towards you to engage a higher gear.Pull the control “-” towards you to change down.
These controls do not permit you to select neutral or reverse gear, nor do they enable you to quit reverse gear.
Commands using the gear lever
Place the gear lever in position M, then:Push the lever to change to a higher gear.Pull the lever to change down.
Remarks:When the vehicle reduces speed, for example approach- i n g a s t o p s i g n o r t r a f fi c l i g h t s , the gearbox changes down automatically to 1st gear.
In manual mode, it is not neces-sary to release the accelerator during changes of gear.
A command to change gear is accepted only if the engine speed permits this.As the engine reaches maxi-mum revs and conditions per-mit, the system will automati-cally engage a higher gear.
Re-initialisation
The Electronic Gearbox System requires a re-initialisation after one of the following events:Change of battery or discon-nection of battery.Starting the engine with an assisting battery.
A system malfunction.
To re-initialise the system:Switch on the ignition. A dash and “AUTO” will display in the instrument panel.
Apply the brake pedal.
Wait until you see N, or a gear engaged, in the instrument p a n e l ( a b o u t 3 0 s e c o n d s ) .Release the brake.
Starting is again possible.
Page 63 of 191
6 4
II
ABS system
The ABS system enhances your safety by preventing the wheels from locking in the event of sudden braking or in conditions of poor road adherence. It enables you to retain control of the steering.
The functioning capability of all the electrical components essential to the ABS is monitored electronically before and during your journey. The ABS warning lamp lights up when you switch on the ignition: it should go out after a few seconds.
If the monitoring warning lamp does not go out, that means that the ABS has disconnected because there is a fault. Also, the fact that the monitoring warning lamp comes on durin g the journey shows that the ABS system is inactive. I n b o t h c a s e s , t h e n o r m a l b r a k i n g s y s t e m r e m a i n s e f fi c i e n t , e x a c t l y a s o n a v e h i c l e w i t h o u t A B S . H o w e v e r , i n o r d e r for the security associated with the correct functioning of the ABS to be restored, the vehicle should be examined as soon as possible by a CITROËN dealer.for the security associated with the correct associated with the
On roads with poor adherence (chippings, snow, ice etc.), it is always imperative to drive with prudence.
System of emergency braking assistance
(For vehicles with the ABS system)
The emergency braking assistance system helps you to attain the requ ired braking pressure more rapidly, thus to reduce the stopping distance. It operates as a function of the speed of action on the brake pedal, decreasing the resistance to this action. To prolong this action of the emerg ency braking assistance system, simply keep your foot on the brake pedal.
Emergency braking or sudden deceleration automatically operates th e hazard warning lamps. They will cease to operate automatically, or manually if you press the hazard lamps button on the dashboard.
B R A K E S
Page 64 of 191
A
6 5
II
This system is associated with the ABS and in addition to the ABS. In the event of a loss of control of the vehicle by the driver, the ESP system acts automatically on one or more wheels and also on the engine to bring the vehicle back on trajectory.
Operation
T h e E S P w a r n i n g l a m p fl a s h e s i n t h e i n s t r u m e n t p a n e l i f t h e E S P s y s t e m i s correcting the vehicle's trajectory.
Deactivation
In exceptional conditions (vehicle stuck in snow, soft ground, e tc.) it may prove useful to deactivate the ESP systems to allow the wheels to spin and thus regain traction.Press button A.
The warning lamp associated with control A (ESP Off) lights up, as does the ESP warning lamp on the instrument panel.
The ESP system is no longer active.
The ESP system reactivates:Automatically after the ignition has been switched off.
Automatically when you drive at above approx. 50 k m / h ( a p p r o x . 3 0 m p h ) ( A c c o r d i n g t o v e r s i o n ) .Manually with another press on button A.
Operational anomaly
If the system is malfunctioning, the warning lamp ESP lights up in the instrument panel.
Contact a CITROËN dealer to have the system checked.
The ESP system offers increased driving safety but is not in place to encourage the driver to take additional risks or to drive at excessive speeds.
The functioning of this system is subject to compliance with the manufacturer’s recommendations on wheels (tyres and rims), brake parts and electronic components, as well as with the assembly and repair procedures approved by CITROËN.on wheels (tyres and rims), brake parts and electronic parts and electronic
After any collision, have this system checked by a CITROËN dealer.
E L E C T R O N I C S T A B I L I T Y
P R O G R A M M E ( E S P )
Page 70 of 191
7 1
II
S P E E D L I M I T E R
Disengagement of the maximum speed
Press button 3 located on the end of control A.
This action causes the information “OFF” to appear in the instrument panel screen.
The memorised speed remains displayed and is not cancelled.
Temporary override of the maximum speed
At any time, it is possible to go above the memorised maximum speed by pressing the accelerator pedal hard down past the tight spot.
W h i l e t h e m e m o r i s e d s p e e d i s b e i n g e x c e e d e d , t h e d i s p l a y e d s p e e d fl a s h e s .
You have only to release the accelerator pedal to return below the maximum speed, to restore the function.
Remark: If during speed limitation the system cannot keep to the maxi mum speed (especially on a steep descent or i f y o u a c c e l e r a t e t o o h a r d ) , t h e s p e e d fl a s h e s . A d a p t y o u r s p e e d a s n e c e s s a r y .
The function will re-engage when your speed has returned below the desired maximum.
To cancel the functionBy moving the control from position “LIMIT” to position 0.Or stop the engine.
The speed that you chose is memorised.
I f t h e r e i s a m a l f u n c t i o n , t h e m e m o r i s e d s p e e d w i l l fl a s h a n d t h e w a r n i n g l a m p “OFF” will come on permanently in the display. Contact a CITROËN dealer. I f t h e r e i s a m a l f u n c t i o n , t h e m e m o r i s e d s p e e d w i l l fl a s h a n d t h e w a r n i n g l a m p “ I f t h e r e i s a m a l f u n c t i o n , t h e m e m o r i s e d s p e e d w i l l fl a s h a n d t h e w a r n i n g l a m p “
A fl o o r c o v e r i n g t h a t i s n o t r e c o m m e n d e d b y C I T R O Ë N m a y s l i d e u n d e r n e a t h t h e a c c e l e r a t o r p e d a l and thus prevent the tight spot from being crossed.
It will then be impossible to exceed the chosen speed, except by an action on the controls under the steering wheel.
The driver still has to remain attentive and in complete control of his vehicle.
Page 109 of 191
1 0 9
IV
F U S E S
Fuseboxes
There are two fuse boxes, one below the dashboard and one under the bonnet.
Dashboard fuses
To access the fuses under the dashboard, detach the cover by slidi ng your fi n g e r s i n t h e s p a c e b e t w e e n t h e b o t t o m o f t h e d a s h b o a r d a n d t h e s t e e r i n g wheel.
Replacing a fuse
Before replacing a fuse, you should ascertain the cause of the fault and have it remedied. The numbers of the fuses are indicated on the fusebox.
GoodBad
Pliers AReplace the fuse that has blown with one of the same rating (same colour).
Use the special pliers A stowed on the cover close to the fuseboxes, this includes a compartment for replacement fuses.
Page 110 of 191
1 1 0
IV
T A B L E O F F U S E S
D A S H B O A R D F U S E S
Ref.RatingFunction
35 AAirbags
410 A D i a g n o s t i c s o c k e t – P a r t i c l e fi l t e r a d d i t i v e – C l u t c h s w i t c h – S t e e r i n g a n g l e s e n s o r
530 A –
630 AScreen wash
820 ADigital clock – Controls at the steering wheel – Radio – Display
930 A C i g a r - l i g h t e r – D i g i t a l c l o c k – I n t e r i o r l a m p s – V a n i t y m i r r o r
1015 AAlarm
1115 AIgnition switch – Diagnostic socket
1215 AAirbag ECU – Rain and brightness sensor
1415 AParking assistance – Instrument panel – Air conditioning – Blueto oth® telephone®
1530 A Central locking – Deadlocking
1740 ADemisting - deicing of the rear screen
18SHUNTCUSTOMER PARK SHUNT
Page 120 of 191
A
119
V
Roof bars
For your safety and to avoid damage to the roof, you should use roof bars that are tested and approved by AUTO-MOBILES CITROËN for the design of your particular vehicle.For your safety and to avoid damage to the roof, you should use safety and
Recommendations:Spread the load evenly, avoiding overloading on one side.Position the heaviest weight as low down as possible.
Tie the load down securely and add warning signs if it is protruding.
Drive conservatively, as the vehicle will be more vulnerable to si de winds.The stability of your vehicle may be altered.
Remove the roof rack or roof bars when you are not using them.
When you are using a towbar, remove the jack from its stowage i n the spare wheel. Keep the jack to hand in the passenger compartment.
S A F E T Y R E C O M M E N D A T I O N S
Towbar
W e r e c o m m e n d y o u t o h a v e t h i s d e v i c e fi t t e d b y a C I T R O Ë N D e a l e r , w h o w i l l b e a c q u a i n t e d w i t h y o u r v e h i c l e ’ s t o w -ing capability and with the procedures necessary for installing a safety item of this kind.
Dimensions (in metres)
A : 0 , 7 1
Do not exceed the maximum permitted load.
For the maximum distributed load on the roof bars: see the chapter “General”.
Page 121 of 191
4
3
52
1
1 2 0
V
C H A N G I N G A W H E E L
Never get underneath the vehicle if it is supported only by the jack.
When changing a wheel, it is essential to park the vehicle safely on level and stable ground.
Access to the tools
To access the toolkit:Tilt the RH seat as if to enter the rear of the vehicle,.
Locate the kit under the seat and pull it towards the rear of the vehicle.
The jack is stowed in a protection box inside the spare wheel under-neath the boot.
Tools1. Wheelbrace.2. Movable towing eye.3. Central embellisher removing tool for accessing the wheel bolts (For vehicles with alumin-ium wheel rims).4. Tool for removing wheel bolt protectors (For vehicles with aluminium wheel rims).5. Extension.
The alloy wheel anti- theft sockets are to be found in the glovebox.
Light alloy wheels
If your vehicle has light alloy wheel rims but a steel spare wheel, if you fi t t h e l a t t e r i t i s n o r m a l t o n o t i c e that the wheel bolts do not appear to contact on the rim.
The spare wheel is secured by the conical tapering of the wheel bolt’s shaft (See illustration).
w h e n r e fi t t i n g t h e l i g h t a l l o y w h e e l , make sure that the tapering contact faces of the wheel bolts are clean and in good condition.