DESCRIPTION
2-1
2
EAU10410
Left view1. Fuse box (page 6-30)
2. Front fork rebound damping force adjusting bolt (page 3-21)
3. Front fork spring preload adjusting bolt (page 3-21)
4. Front brake fluid reservoir (page 6-22)
5. Idle adjusting screw (page 6-16)
6. Shock absorber assembly spring preload adjusting knob (page 3-23)
7. Shock absorber assembly compression damping force adjusting bolt
(for fast compression damping) (page 3-23)8. Shock absorber assembly compression damping force adjusting screw
(for slow compression damping) (page 3-23)
9. Battery (page 6-29)
10.Fuel injection system fuse (page 6-30)
11.Main fuse (page 6-30)
12.Owner’s tool kit (page 6-1)
13.Engine oil drain bolt (page 6-8)
14.Engine oil filter cartridge (page 6-8)U4B1E0E0.book Page 1 Wednesday, October 12, 2005 2:32 PM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
63. Start the engine, warm it up for
several minutes, and then turn it
off.
4. Place an oil pan under the engine
to collect the used oil.
5. Remove the engine oil filler cap
with the special wrench.
6. Remove the engine oil drain bolt to
drain the oil from the crankcase.
NOTE:
Skip steps 7–9 if the oil filter cartridge isnot being replaced.
7. Remove the oil filter cartridge with
an oil filter wrench.
NOTE:An oil filter wrench is available at aYamaha dealer.
8. Apply a thin coat of engine oil to
the O-ring of the new oil filter car-
tridge.NOTE:Make sure that the O-ring is properlyseated.
9. Install the new oil filter cartridge
with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.
1. Cowling
2. Projection
1. Engine oil drain bolt
1. Oil filter wrench
2. Engine oil filter cartridge
1. O-ring
U4B1E0E0.book Page 10 Wednesday, October 12, 2005 2:32 PM
PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
6 10. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
NOTE:Check the washer for damage and re-place it if necessary.11. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap
with the special wrench.
CAUTION:
ECA11620
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
Make sure that no foreign mate-rial enters the crankcase.12. Start the engine, and then let it idle
for several minutes while checking
for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
NOTE:After the engine is started, the engine
oil level warning light should go off if theoil level is sufficient.CAUTION:
ECA10400
If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha dealercheck the vehicle.
13. Turn the engine off, and then
check the oil level and correct it if
necessary.
14. Insert the projection into the slot,
and slide the cowling into its origi-
nal position.
1. Torque wrenchTightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter cartridge replace-
ment:
2.90 L (3.07 US qt) (2.55 Imp.qt)
With oil filter cartridge replacement:
3.10 L (3.28 US qt) (2.73 Imp.qt)
U4B1E0E0.book Page 11 Wednesday, October 12, 2005 2:32 PM